The car wiper won t move, what s going on?

When the car wiper fails and cannot be moved, you can check the following possible causes of failure:

1. Open the guide cover to observe whether the transmission connecting rod is dislocated (this reason is the most common).

2. Check whether the fuse is in good condition.

3. Disassemble the motor cord plug to turn on the power supply, and measure whether there is voltage with a multimeter.

4. If the fuse is intact and the motor has no voltage, check whether the circuit and direction light combination switch are in good condition.

5. Generally, the motor will burn out.

6. If you turn on the power supply and measure the normal voltage at the wiper motor, you can consider that the motor is broken.

What happens when the wipers suddenly don't move.

1.First refer to the manual of the car with the bai to figure out what du is used

What model of wiper zhi. dao

2.Because some of the arms are fixed with screws.

version to the rocker arm, while.

Some of the rights are locked with a convex buckle.

3.Pull the wiper up and touch it with your finger to check for damage to the cleaned rubber wiper and the elasticity of the rubber blades. If the blades are aged, hardened, or cracked, then the wiper is broken.

4.Especially in the intermittent working state, it is also necessary to pay attention to whether the wiper maintains a certain speed when it is in motion.

5.Check the wiper status and whether the wiper rod has uneven swing or leakage. If the following three situations occur, this wiper is not qualified:

First, the swing is not smooth, and the wiper is not beating normally; Second, the contact surface of the rubber and the glass surface cannot be completely fitted, resulting in wiping residue; Third, after wiping, the glass surface presents a water film state, and fine stripes, fog and linear residues are produced on the glass.

6.During the test, attention should be paid to whether there is abnormal noise in the motor, especially when the wiper motor "hums" and does not rotate. This indicates that the mechanical transmission part of the wiper is rusted or stuck, and the wiper switch should be turned off immediately to prevent the motor from being burned.

7.Some people believe that the longer the wiper blade, the larger the brush area, and the better the visibility. Wiper blades aren't always better. Although lengthening the length of the wiper blades can increase the visible range, it will also increase the burden on the wiper motor and wiper rod.

What happens when the wipers suddenly don't move.

Hello, check your wiper protection first for the first copy

Whether the risk is good, and then see if the DU motor is burned out, or whether the linkage rod has slipped, or whether the combination switch has contact. , It's an honor to solve your car problem, I wish you a pleasant experience! [Car questions, ask the car master.]

4S shop professional technician, 10 minutes to solve. 】

It depends on what your car is! It may be that the connector of the motor is not connected properly! It could also be that the insurance of the motor is broken! You turn the rain officer to the maximum gear, and gently help it with your hand to see if it can be turned? If you can turn it, it will be the induction of the rain officer, and the rust will die, and you can clean it up.

It could be that the wiper drive motor fuse burned out!

Depending on the wiper usage, there is no fixed time. The daily inspection of the wiper is very simple, spray out some cleaning liquid, start the wiper, pay attention to whether its movement is smooth, the wiper listens to whether there is a loud sound, if so, it means that the wiper is too pressed against the glass, and appropriate adjustment must be made.

If it is a cold area such as the Northeast, check whether it is frozen, otherwise it may be that the wiper motor is damaged, if it is frozen, the wiper can not be forcibly started, otherwise it will burn out the wiper motor, and it should be thawed in a warm way before it can be used.

Second, check that the joystick is properly attached to the wiper rocker. Because some arms are screwed to the wide core of the rocker arm, while others are locked with a convex buckle.

There are several reasons why the wipers of a car do not move:

1. It may be that the connector of the motor is not connected properly, and the lower line needs to be reconnected before it can be used.

2. Turn the wiper to the largest gear and gently dial it with your hand to see if it can rotate, if it can rotate, it can be rusted on the induction of the wiper, and you can clean it directly.

3. Check whether the safety of the wiper is intact and whether the fuse is burned out, and then check whether the electric rubber machine is burned out, whether the connecting rod is slipped, or whether the combination switch is in poor contact.

Photo by Tang Yanyan of Pacific Automobile Network).

What's going on with the car wiper not moving The car wiper is broken. If it is in a cold region such as the Tohoku, check if there is any freezing first. Otherwise, the wiper motor may be damaged.

If it freezes, you can't force the wiper to start, otherwise it will burn out the wiper motor. It should be thawed with warm water before use. Second, check that the joystick is connected to the wiper rocker arm in the correct way.

Because some arms are fixed to the rocker arm with screws, and some are locked with a convex buckle. There are several reasons why car wipers don't work:1

It is possible that the connector of the motor is not well connected and needs to be reconnected to the line before it can be used. 2.Turn the wipers to the highest setting and gently stir with your hands to see if they turn.

If it can be rotated, it means that the sensor of the wiper is rusty and can be cleaned directly. 3.Check whether the fuse of the wiper is intact, whether the fuse is blown out, and then check whether the motor is blown out, whether the connecting rod is slipped, or whether the combination switch is in poor contact, etc.

Generally, family car wipers are equipped with standard, fast and slow three gears, which can be adjusted, generally on the right side of the steering wheel. There may be some differences between models.

The manual wiper adjustment method is as follows:

Light rainfall: Don't rush to use wipers when it starts to rain lightly. Spray glass water to moisten the glass before opening it for the first time to avoid dry scraping of the glass window due to lack of moisture.

Heavy rainfall: If the rain is heavy, adjust the working frequency of the wiper in time to ensure a clear vision. If the rain is too heavy and the rain is too urgent, and you still can't see clearly when you drive to the highest gear, it is recommended to find a safe place to stop temporarily and wait for the rain to lighten, and remember to turn on the fog lights and double flashes when parking on the side of the road to avoid accidents.

Use rear window wipers: If your car has a rear wiper, don't forget to turn it on when it rains.

Generally, SUVs, hatchbacks, MPVs and other models are mostly equipped with rear wipers, this is because the rear windshield of the sedan has air flow through, while the hatchback or SUV does not, which leads to the fact that once there is rain, the sedan can use the air flow to blow down the water droplets, but the hatchback cannot, the water can not be blown off in time, it will be easy to stick to the dust, affect the sight of the rearview mirror, and lead to unsafe driving.

Hope, thank you.

The possible reasons why the car wiper does not move are: the wiper slippery fuse is blown and the wiper motor is burned out, and the messenger leather wiper switch is damaged. You can go to the nearby repair shop to check the cause and troubleshoot.

The following is a specific introduction: 1. Introduction to the exclusion method of the automobile wiper immobility: the automobile wiper may not move because the fuse (to prevent circuit overload) is blown and the wiper cannot work normally, then the fuse box should be opened to check whether the corresponding fuse is blown or not.

2. Precautions for replacing the fuse: Before replacing the fuse, be sure to close all the electric doors of the car. It is also necessary to consider that the probability of motor burnout is very low, but it may also be a problem with quality control.