Telecom cat model TEWA 300AIG how to set wifi 5

It is recommended to connect another router If you only use a cat, the wireless signal sent can only be used by devices with dial-up function, and the connection success rate is not high!

China Telecom's broadband cat has the function of wifi, but it is locked and cannot be used, there is only a wireless signal, and there is actually no network, and you must buy a wireless router to use the wireless network. Click **** to get more services, customer service 324 will answer for you.

1. Many people will not be able to turn on the router or the setting of the wireless cat**! You can open the step to ignore directly!! Most of the reasons that can't be opened are due to IP settings!!

The default settings for telecom cats are all . Right-click on Online Neighbors - Properties if you can't open it. Then right-click on Local Connections - Properties!!

2. Then select the Internet Protocol!! Then click on the Properties button!!

3. Then enter the IP address: . The submask comes out automatically, and the default gateway is set to . Then the DNS can be set up after the router is filled in. Or ask how much telecom broadband is! Then you can open it after saving!!

4. Enter in the browser. Then the login window will appear, as shown below!! The login username and password of the telecom cat are printed on the back of the cat. You can check it out for yourself!!

5. Then click on the network inside the navigation! The first time you use it, you will need to set a login name and password. It is the account name and password provided by Telecom! Then start by enabling the wireless network. Just tick it off. Then click on the Advanced button!!

6. Click Advanced to set the wifi password and click Save!!

7. Then click on the navigation in the management - device management, and restart the router!!

1. Many people will not be able to turn on the router or the setting of the wireless cat**! You can open the step to ignore directly!! Most of the reasons that can't be opened are due to IP settings!!

The default settings for telecom cats are all . Right-click on Online Neighbors - Properties if you can't open it. Then right-click on Local Connections - Properties!!

2. Then select the Internet Protocol!! Then click on the Properties button!!

3. Then enter the IP address: . The submask comes out automatically, and the default gateway is set to . Then the DNS can be set up after the router is filled in. Or ask how much telecom broadband is! Then you can open it after saving!!

4. Enter in the browser. Then the login window will appear, as shown below!! The login username and password of the telecom cat are printed on the back of the cat. You can check it out for yourself!!

5. Then click on the network inside the navigation! The first time you use it, you will need to set a login name and password. It is the account name and password provided by Telecom! Then start by enabling the wireless network. Just tick it off. Then click on the Advanced button!!

6. Click Advanced to set the wifi password and click Save!!

7. Then click on the navigation in the management - device management, and restart the router!!

Tool: Telecom Cat.

Router computer.

2 network cables. The steps are as follows:

1. Plug the network cable into the LAN port of the telecom modem and the wireless router respectively;

2. Plug one end of the network cable into the LAN port of the router and the other end into the network port of the computer;

3. Enter the router background login address in the browser to enter the router background management login page;

4. Enter the login password;

5. Click "Route Settings";

6. Click "Internet Settings";

7. Select "Automatically obtain IP address" in the Internet mode;

8. Click and select "DHCP Server" on the left.

9. Select "Off" to turn off the DHCP service function of the router and the setup will be completed successfully.

Telecom modem wireless router that needs to dial up, so set up and install:

1. Plug in the wireless router, don't connect the cat first, and connect the computer to any LAN port of the wireless router;

2. Enter the gateway address of the router (on the label behind the router) in the address bar of the browser, and enter the login username and password to enter the settings page;

3. Set up according to PPPoE (ADSL virtual dialing) mode, enter the Internet account and password;

4. Set the SSID, encryption method and password;

5. Save and restart;

6. After setting, connect the network cable from the cat LAN port to the WAN port of the wireless router.

Tools and materials required: wireless router, telecom tewa-300EA optical modem.

The method is as follows: 1. Hardware connection:

2. Open the browser, enter the IP address of the router), enter the router account and password (see the label or manual on the router box);

3. Click Next;

4. Select PPPOE (ADSL Virtual Dialing) in the Internet mode, and click Next;

5. Enter the broadband account provided by the broadband operator in the Internet account and the broadband password in the Internet password;

6. Set the wireless network name in the SSID, select the WPA-PSK WPA2-PSK encryption method, and set the wireless password of no less than 8 digits in the PSK password;

7. Click Restart, and the router is set successfully.

1. Connection: The LAN port of the router is connected to the computer with a network cable, and the computer IP is configured to automatically obtain and log in to the router (enter in the address bar: press enter, and enter the username "admin" and password "admin" on the login page);

2. First of all, in the WAN port: choose the Internet mode, if it is home broadband, select the second PPPoE (ADSL virtual dialing), and then fill in your broadband account password point to save, 3. Set the wireless login password (security option wpa-psk wpa2-psk, enter the key);

4. Modify the management address of the router (that is, modify the LAN port address): Because the Tianyi TEWA-300EA optical modem has already been occupied, you need to modify the LAN port address of the router, such as your router address is set to, so that the addresses between the two network devices will not conflict. Note that in the future, you will have to log in with a modified address to log in to the router;

5. Save the parameters and connect the network cable from the Tianyi TEWA-300EA optical modem to the WAN port of your router, and the router is set up at this point.

1. First come.

The computer is connected to the network port source of the optical modem, and the computer does not set dial-up to see if it can directly access the Internet. If it can, it is the optical modem that integrates the routing function and can automatically dial up the connection.

2. In this case, connect the network cable of the modem network port to the LAN port of the router, and connect the computer and other wired equipment to other free LAN ports. (The computer network card uses the default automatic setting).

3. If the computer is directly connected to the modem and needs to dial up to access the Internet, it means that the modem cannot be automatically dialed up (or not set) to connect.

4. Then the network cable of the optical modem network port should be connected to the WAN port of the router, and the computer should be connected to the LAN port, according to the manual, enter the router settings page, and fill in the account and password of your home broadband Internet access correctly. and set up other functions such as wireless. Save, restart.

That's it.

The reason why the router is set to the dynamic state and the DUIP cannot go to the network.

Yes, the IP address automatically obtained by the router is in the same segment as the LAN address of the router DAO, that is, the IP address is the same as the previous three segments. Definitely can't go online.

The best solution: Connect the network cable separated by the modem to the LAN port of the router and turn off the DHCP function of the router. Change the last digit of the LAN address of the router to a number after 2.

Disconnect the optical modem dial-up because the router has its own dial-up function, and set the PPPoE dial-up mode in the router.

Tool: Telecom Cat.

Router. Computer.

2 network cables. The steps are as follows:

1. Plug the network cable into the LAN port of the telecom modem and the wireless router respectively;

2. Plug one end of the network cable into the LAN port of the router and the other end into the network port of the computer;

3. Enter the router background login address in the browser to enter the router background management login page;

4. Enter the login password;

5. Click "Route Settings";

6. Click "Internet Settings";

7. Select "Automatically obtain IP address" in the Internet mode;

8. Click and select "DHCP Server" on the left.

9. Select "Off" to turn off the DHCP service function of the router and the setup will be completed successfully.

1.The computer browser opens the "This is the login interface for the wireless cat settings,:telecomadmin password:ne7ja%5m (this messy password is the telecom administrator,You can copy and paste the past,Pay attention to the number of digits)

2.After entering the wireless modem settings interface, select "Network - Broadband Settings". Take note of the VPI and VCI values in the middle of this interface. Impact-resistant.

3.After the connection name is a drop-down menu, select them one by one, and click "Delete" at the bottom of the screen to delete the drop-down menu.

4.Select "New WAN Connection" after the connection name, then fill in your own broadband (** with area code) and password at the bottom of the interface, and other settings do not need to be changed (VPI and VCI should be the same as in the second step), and finally click "Create" at the bottom.

If you don't have ITV left, please skip this step. Continue to "New WAN Connection", select "LAN 2" (i.e., ITV port) as the binding option, select "Bridge" as the mode, click on the drop-down menu to select the previous step, and finally click "Create" below.

6.On the wireless modem settings page, select Network - DHCP Configuration, and enable the DHCP service checkmark (default).

7.Wireless cat settings interface, select "Network - WLAN configuration", change the name and password of WiFi (no problem if you don't change it, but the default is not easy to remember.)

8.On the Wireless modem settings page, select "Management - Device Management" and "Restart". (There is a "factory reset" below, for help).

9.Delete the "Dial-up Connection" on the computer and fill in the IP &DNS to access the Internet.

10.After connecting to wifi on your mobile phone, you can access the Internet without PPPOE.

The optical modem must be cracked by the super password before it can use the wireless network.