How to set up wireless functions for telecom broadband modems?

There are two ways to use wireless networks for telecom wireless cats:

1. Crack the wireless cat and realize the wireless routing function.

The wireless cat is customized by telecommunications, and the wireless routing function is limited, and the wireless routing function can only be realized after cracking, so that mobile phones, laptops, and pads can access the Internet wirelessly. At the same time, the desktop computer has wired Internet access (no dial-up, direct Internet access).

There are many cracking tutorials on the Internet, and the cracking of wireless cats is different for each model. You search for the model of your wireless modem, find the tutorial, and check the settings.

Second, it can also be connected to a wireless router to achieve wifi Internet access.

You can also buy a wireless router and follow the following method to set up wireless Internet access:

1. Plug in the wireless router, don't connect the cat first, and connect the computer to any LAN port of the wireless router;

2. Enter the gateway address of the router (on the label behind the router) in the address bar of the browser, and enter the login username and password to enter the settings page;

3. Set up according to PPPoE (ADSL virtual dialing), enter the Internet access and password;

4. Set the SSID, encryption method and password;

5. Save and restart;

6. After setting, connect the network cable from the cat LAN port to the WAN port of the wireless router.

First of all, it depends on whether your telecom cat supports wireless, if not, you can install a wireless router downstream of the cat (about 100, cheaper on the network).

The cat doesn't have that function, and the wireless function has to buy a wireless router again.

1. If it is an optical fiber that needs to be dialed up, set it up like this.

1. Plug in the wireless router, do not connect the cat or the network cable into the home first, and connect the computer to any LAN port of the wireless router;

2. Enter the gateway address of the router (on the label behind the router) in the address bar of the browser, and enter the login username and password to enter the settings page;

3. Set up according to PPPoE (ADSL virtual dialing) mode, enter the Internet account and password;

4. Set the SSID, encryption method and password;

5. Save and restart;

6. After setting, connect the network cable from the cat LAN port or the home network cable to the WAN port of the wireless router.

Second, if it is an optical fiber that does not require dial-up, it can be connected to the computer to access the Internet, so it is set up.

1. When the wireless router is plugged in, do not connect it to the home network cable first, and connect the computer to any LAN port of the wireless router;

2. Enter the gateway address of the router (on the label behind the router) in the address bar of the browser, and enter the login username and password to enter the settings page;

3. Set it in a dynamic way;

4. Set the SSID, encryption method and password;

5. Save and restart;

6. After setting up, connect the home network cable to the WAN port of the wireless router.

Dear users, hello;

1. At present, Anhui Telecom's broadband cat change routing mode has been liberalized. For details, please consult the local 10000 or broadband installation master. See also the web-related cracking manual.

2. If you cannot access the Internet after cracking, you can modify the relevant Internet access methods (PPPOE, DHCP, IP) to achieve normal use.

Hello, you can set it up as shown below:

The most important thing is to see how you can surf the Internet without connecting to the router, remember it.

Connection: (refer to the router manual).

The final network cable of the network ** provider is plugged into the WAN end of the wireless router (no network cable is plugged in when set), and the network cable of all computers is plugged into the LAN end of the router.

Settings: (refer to the router manual).

1.Remember the settings of the business to you, and if you can't remember it, you can ask them; Use these parameters to set the WAN side of the router.

2.Configure the LAN side of the router: Enable DHCP service.

3.Set the WLAN side of the router: Set the password, which is generally safer to use WPA now. Remember the name of the outgoing signal from the wireless router, and the password for backup.

4.Check whether the gateway address of the final network cable plugged into the computer is the same as your wireless router address, if it is the same, please change your router address, for example, you can change yours.

5.Set all Internet devices to get addresses automatically.

That's basically it, remember: the WAN setting method is determined by the network cable plugged into the WAN side, and the WLAN setting password is up to you.

Thank you for your question.

1. Connect the router to the computer directly with the network cable, before entering the IE, press the router restart reset button, restore to the factory properties, log in to the wireless router, enter the network settings, and modify the LAN address;

2. Connect the set router to the network, optical modem, select the router, turn on the computer, log in to the router, enter the installation wizard interface, set the WAN port to dynamic IP, and follow the prompts to the end.

Only cats can not set up wireless networks, cats are also known as modems, he can make ** line Internet, after connecting the cat you also need to connect 1 wireless router to set up wireless network.

A different wireless router will do.

Hello, you can install a wireless router to use the wireless network, the router installation and setting method is as follows:

2. Then open the browser and enter the management address and login password of the router.

3. After logging in to the background, click the setup wizard, and then fill in the corresponding parameters according to the wizard instructions.

6. After the wireless setup is completed, click Save, and then restart the router to use it normally.

Didn't it prompt you, dial-up failed, the server did not respond, you look at the terms of your contract, is it too many computers at the same time. Problem 1WAN port is not properly connected to your ADSL modem, check whether the network cable of the ADLS device is connected to your WAN port, and if it is a monthly broadband, you don't need to connect on demand, just connect it all the time Question 2, ADSL cat has no signal, if the signal light is not constant, you need to call telecom maintenance** to solve the problem. Question 3 It is rare for your router's MAC address to be the same as the MAC address of other users, and this situation will also occur, you can change the MAC address of your router to try.

Installation Setup Method:

1. Connect the network cable from any LAN port of the cat to the WAN port of the wireless router, and connect the network cable to the computer on the LAN from the wireless router, and automatically obtain the IP address and DNS settings of the local connection;

2. After powering on the wireless router, connect the computer to the wireless router and change the LAN address IP to; Avoid conflicts between the IP address of the cat and the IP address of the wireless router.

3. Open the browser, enter enter, enter the management username and password (the login address, management username and password are indicated on the back of the wireless router), confirm, and log in to the wireless router settings interface;

4. Setup wizard, next, select PPPoe dial-up mode, next, enter the Internet account and password, next, set the wireless network name in the SSID box, enter at least 8-digit wireless network password in the psk box, next step;

5. Save, restart the wireless router from the system tool to complete the installation of the wireless router.

Dear users, hello; We'll be happy to answer your questions. Based on the information you provide. It is recommended that you set up your wireless router according to the method I provided below, I hope it can help you.

1.First, factory reset your wireless router, there is a button or hole in the wireless router that is specially used for factory reset. You can press for more than five seconds and release to restore factory settings.

2.The LAN port of the router is connected to the computer, remember, do not connect the cat. Connect only the LAN port of the router to the computer.

First set the IP address of the computer and the IP address of your router in the same frequency band, for example, the IP of the router is set to the IP of any of the default gateways set to the IP of the router Enter the correct IP address of the router in the browser, enter the settings interface, remember, don't move anything, follow the setup wizard to set up, just set up PPPOE and enter the correct account number, password and then set the wireless password.

3.Once you're set up, restart your wireless router.

4.Connect the port of the cat to the WAN port of the wireless router, and connect the LAN port of the wireless router to the computer. Restart all devices.

5.Set your computer's IP address and DNS address to be obtained automatically.

6.Normal use.

At present, Anhui Telecom Network Department carries out relevant mobile phone preferential activities. If you need to buy a phone, please log in to the Anhui Telecom network hall** to buy the latest mobile phone. If you need to check the bill and pay the phone bill, please log in to the online business hall of Anhui Telecom, and get 2 yuan for 100 yuan.