How to install wireless router to the telecom modem

1. Connect through the network cable or wireless connection, enter the address in the address bar below, and the general initial address is;

2. Enter the username and password in the pop-up dialog box; The initial password and user name are generally admin, and the specific can be viewed on the router, usually on the back of the router;

3. Enter the router selection and setting wizard, click Next, and select PPPoE (ADSL virtual dialing) as the Internet mode;

4. Enter the broadband password below, if it is a monthly subscription, you can enter it, if it is not a monthly subscription, you should consider it, after entering the password, the computer will be automatically dialed up after the Internet is turned on. This means that you don't have to manually connect to broadband every time. If you don't want to automatically dial up the Internet, you can leave it out here;

5. The first two of the following are set to the signal name of the wireless router, which can not be changed; The second is the wireless router key, it is recommended to change it;

6. The first two of the following are set to the signal name of the wireless router, which does not matter and can not be changed; The second is the wireless router key, it is recommended to change it;

Dear users, hello:

Home Wireless Router Operation:

1. Connect the computer to the wireless router, turn on the computer, and enter the general router address in the browser, you can check the back of the router, whether it is this address, or if not, change the address on the back of the router.

2. Enter the router settings, select the setup wizard, select the opppe dialing type, follow the next step of the wizard, enter the dialing and password, and select auto-dialing. The setup is complete. It's best to change the router IP to when setting up the router to avoid conflict with the IP of the wireless modem.

3. The cat or fiber to the home interface is connected to the router, and the router is connected to the computer. The computer can directly access the Internet, and the mobile phone and tablet can be wirelessly connected to the router to access the Internet.

4. If it cannot be used after setting, it is recommended to dial 10000 to see if the router is prohibited from being used, or to check whether the router is damaged.

Anhui Telecom will serve you wholeheartedly, I hope mine can get yours.

If you have any questions, you can go to Anhui Telecom online business hall to consult the staff, Anhui Telecom has recently had a mobile phone to grab New Year's goods, you can check it when you have time, I wish you a happy life!

The cat is outgoing and then connected to the WAN port.

The computer is connected to the LAN port.

The incoming route setup wizard next step can be done.

Okay, reboot down.

Basically, that's fine.

Then don't wait 15 minutes.

The network cable out of the cat is directly connected to the WAN port of the wireless router, and the wireless router is set up, right?

Connect the line first, power on each device after connecting, and then turn on the computer, open the IE browser, enter the router settings, dial up the wideband and answer the network, and then save and restart the router.

1. Connect the line between the network cable, the router and the computer, and start the computer and the router equipment;

2. Look at the nameplate or instruction manual at the bottom of the router to find the router IP, default account and password;

3. Open the browser, enter the IP address and press enter, such as;

4. Enter the router login interface, enter the default login account and password queried, if the input prompt is incorrect, it means that it has been modified, and can only be reset after resetting the router by pressing and holding the reset button on the router;

5. Enter the router settings interface, find the setup wizard on the left menu bar, select Next according to the prompts, and select PPPoE dial-up Internet access;

6. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

7. Set the wifi password, try to make the alphanumeric combination more complicated and not easy to be rubbed off the network (this step is for the router with wifi function, and without wifi function, go directly to the next step);

8. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

Telecom wireless modem continue to install wireless routers, steps:

1. Connect a line from the LAN of Route 1 to the WAN of Route 2, and then connect Route 2 to the power supply.

Press and hold the energized route 2 with a small thin wire until the factory setting position is restored. (About 3-5 seconds, after flashing, you can use the computer to search for the wifi emitted by router 2 and connect it (generally passwordless).

3. Open IE browser, enter in the address bar, and press Enter. At this time, the system will prompt you to enter the username and password, and you can enter admin as the username and password, and you can enter the routing management interface.

4. Change the LAN address of route 2 from the original, and then restart route 2 After restarting, if the computer automatically obtains the IP, you don't need to change it, if it is manual, change the address of your local connection, change from the original to the gateway from the original to the LAN address of route 2 that you just redefined, you must change it, otherwise you won't be able to enter route 2.

5. Browser input, after entering, the system will automatically prompt the configuration setting wizard.

6. Find DHCP of route 2 and enable it instead (it is generally enabled by default).

7. On other computers, configure the computer IP according to the LAN parameters of route 2, and then you can access the Internet, such as the subnet gateway.

8. After connecting to the Internet with router 2, the shared printer configured on router 1 (you can also print the things in the router 2 computer directly.)

The routing function of the telecom modem is turned off, connected to your wireless router, and the DHCP address is drawn a few more.

I've renovated my home, see if I can help you, I bought another cat, first my cat, and then wireless routing and then wireless cat.

Direct modem and wireless router connection will do just that.