The difference between Huawei 5030dn s and 5030 dn

Huawei AP5030 and AP5010].

1. The wireless rate is different, AP5030 is; AP5010 is 300Mbps;

3. Working frequency band: AP5030 is 3 3 dual band; The AP5010 is dual-band (, 5GHz);

4. Dimensions: AP5030 is 220 220 53mm; The AP5010 is 180 180 50mm.

This is an enterprise-class AP that cannot be used independently and must be used in conjunction with an AC to be used in wireless networking.

The following table describes the Huawei AP5030DN router settings:

1. First of all, one of the things you need to do after connecting the wireless router is to check whether it is powered on and whether the wireless router is running normally.

2. After checking that it is correct, open the browser and enter: press Enter to enter, at this time a dialog box pops up, you need to enter the account name and password, this does not have to worry, there will be in the back of the router, you can log in if you find it, in general: account name:

admin password: admin

3. After entering the password behind the router, you can log in to the settings page of the router.

4. Click on the setup wizard on the page, and a box will appear that will lead you to set up the router, and follow its requirements step by step.

5. Click Next to enter the account password settings, this account password is your current network access account password, if you don't know, you can ask your operator.

6. After setting up the account and password for Internet access, it is the function of wireless Internet access, set your wifi name and wifi password, it is recommended that the password is not too simple, it is easy to be cracked, and the encryption method can be recommended by the system, which is safe and secure.

7. Click Done, congratulations, at this point, your router setup has been successful.

1. The wireless speed alarm rate is different, AP5030 is; AP5010 is 300Mbps; Talk about blindness.

3. Working frequency band: AP5030 is 3 3 dual band; The AP5010 is dual-band (, 5GHz);

4. The shape is changed to size: AP5030 is 220 220 53mm; The AP5010 is 180 180 50mm.

Hello, what is the problem with Jibo Sun, Jianzi Chain advises you to go to Huawei's official website Technical Support Pollen Club Silver and Department The section of the corresponding model of your mobile phone, go here to ask questions, there are Huawei professional engineers who are much more professional.

There is also an uplink to connect the mouth of ONU! Unicom is equipped with the first 20 ports connected to AP! However, you have to reserve a few, generally up to 16 units! The 4 ports at the back are connected to ONU and reserved.

The AP4050DN-E uses a dual-band omnidirectional antenna.

AP4050DN-HD high-density smart antenna.

The difference is that the 4050 is a 30x zoom.

The 4050 is new, and the picture is much better than the 2900.

Hello, I am specialized in the production of mobile phone data cables, the question you asked, 99% can be universal, because now the state uniformly stipulates that the interface of the Android system is V8 common interface, only Android mobile phones can be universal, please rest assured to use!

AP4050DN-HD has a built-in dual-band directional antenna (lobe angle 30 degrees).

The AP4050DN-E has a built-in dual-band omnidirectional antenna.

Huawei's AP5010 SN-GN-DC router is a very good enterprise router. Network standardIEEE, IEEE, IEEE Maximum transmission rate 300Mbps Network interface 1 x 1000Mbps LAN port Frequency range single frequency (, the following is the parameter information: Network standard:

ieee ，ieee

The following describes how to set up the Huawei AP5030DN router:

1. Turn on the power supply of the router, and then plug the incoming cable of the broadband network into the WAN port of the router (usually the blue port), and then connect it with the computer network card.

The connected network cable is plugged into a LAN port at random.

2. Enter the IP address you see on the instructions at the bottom of the router in the browser, generally, and then enter the login interface, enter the account and password of the router, which is generally admin.

3. After confirmation, enter the setting interface and click the setup wizard. (Generally, it pops up automatically).

4. Click Next to enter the Internet access mode settings, you can see that there are three Internet access methods to choose from, if it is dial-up, then use PPOE. Dynamic IP can be used by the computer directly plugged into the network, and there is a DHCP server on the upper layer.

Target. Static IP

Generally, it is a private line or something, it may also be a cell bandwidth, etc., and there is no DHCP server in the upper layer, so PPOE is selected because of dial-up.

6. Then click Next to enter the wireless settings, you can see the channel, mode, security options, SSID, etc., wireless security options to choose WPA-PSK WPA2-PSK, so safe, so as not to let people crack and rub the network.

7. After the setting is completed, the router will automatically restart, and then the connection is ready to use.