Does tile adhesive have a water resistant function, and does tile adhesive need to be moistened in a

As we all know, cement mortar is generally used for tiling, but in recent years, there have been more tile adhesives on the market, and I don't know which one is better to use!

Let's look at the cement mortar first, that is, it is mainly cement, add yellow sand and some waterproof additives, and then stir with water, which is basically zero pollution, high adhesion, and preferential treatment.

But the bad thing is that cement mortar is affected by many external factors and is easy to fall off. In addition, the hardness of tiles on the market is getting higher and higher, and the focus is on poor water absorption, so the tiles often fall off.

From the appearance, tile adhesive and cement are almost the same, mainly mixed with water, and then directly used to paste tiles. However, tile adhesive has an advantage that cement does not have, that is, it is less affected by external factors, and it is resistant to low temperature and water. The bad point may be that it is expensive, and there are many bad tile adhesives on the market, and there may even be the problem of excessive formaldehyde.

Compared with cement and tile adhesive, the adhesive performance of ceramic tile adhesive will be better, the point is that you don't need to run the tile in advance, you can paste it directly. There is no need to paint a thick layer on the wall, and it is basically very firm when pasted on.

Of course, good things are generally expensive, so there is no need to use tile adhesive in all places, you can use it in the kitchen and bathroom, because these places are often wet, and it is easy to fall off with general cement.

Do the math how much it will cost you to renovate your home

We all know that tiling is a technical job, so we must choose the right method, at present, many people prefer to use tile adhesive to paste, this kind of paste will be firmer, but must be used correctly. Use an electric mixer for the best blending effect; The proportion of gouache can be appropriately adjusted due to different substrates, weather, construction conditions, etc.; During construction in rainy days, it is necessary to take sheltering and protective measures, and ensure that the construction area is not wet by rain within 24 hours after tiling; The glue should be used within 2-3 hours according to the weather conditions; Do not mix the dried glue with water before use; The tile adhesive should be evenly and fully applied, and the thickness of the adhesive layer should be about half the height of the toothed scraper pitch used. After the brick laying is completed, the next step of the caulking process can be carried out only after the mortar has completely dried (about 24 hours).

When using tile adhesive, we must pay attention to some details, and there is no way to get wet by rain after pasting, which must be noted, or its viscosity will not be so good.

Enter the area and get the decoration for free**].

When it comes to laying wall tiles, many people use concrete. Naturally paving wall tiles can also be applied tile adhesive, the key dust hall is very environmentally friendly, and more solid, it is easy to do the work of clearing and cleaning later. Naturally, in the case of applying tile adhesive, there will also be some doubts, and we are more concerned about whether the tile adhesive has a waterproof effect.

So, can tile adhesive be waterproof? How to construct tile adhesive? We've got you covered.

Can tile adhesive be waterproof.

1. Tile adhesive has the actual effect of waterproofing, and the tile adhesive is simple, green and environmentally friendly, and the product does not add harmful substances, and does not cause waste and smoke during construction. First, it does not pollute the environment, and second, it does not endanger the physical and mental health of the construction staff. The construction process is more simplified, and it can be applied by putting water and stirring it on the spot, and it can be tiled without soaking the bricks and wet walls;

2. In the traditional processing technology of environmental protection and energy saving, most of them are made of concrete bricks, which not only lacks strong adhesion, but also consumes a lot of concrete. However, tile adhesive is very economical in raw materials, and the thin surface layer can also cause sufficient adhesion, which can greatly reduce the demand for raw materials. From the traditional paving, the amount of concrete required per square meter is reduced from 11 18kg per square meter to tile adhesive 4....

How to construct tile adhesive?

1: First of all, the reverse side of the floor tile through the number plate will be cleaned and tidy, and the adhesive base surface will be checked. The base surface should be firm, leveled, tidy, zero pollution, loose matter, wall hollowing, etc., with protective agents, film release agents, and smoother concrete surfaces need to be polished and polished after construction.

2: First pour the required water into the "Vertical Mixer" tile adhesive and mix: 20kg tile adhesive + (4-5) kg water.

3: Gradually pour the tile glue granules into the "Stand Mixer". Tile adhesive mixing and formulation:

20kg tile adhesive + (4-5) kg water (tips: please do not add all goods in tile adhesive, such as: concrete, etc., if you need to improve the adhesion, only use a special tile adhesive adjuvant).

4: After pouring water and tile adhesive, then mix with an "electric mixer" until the paste is homometric, particle-free, colloidal precipitation is viscous, and then slightly mixed after a few mm, you can gradually paste the bricks below.

5: During construction, please apply the technical professional "tooth scraper" to scrape the acrylic paint evenly on the surface layer of the work, and scrape about 1 square meter of the construction surface each time. (Tips: Toothed scrapers are commonly used in two specifications and models: 6cm and 10cm).

6: Use the "toothed scraper" to evenly scrape the acrylic paint on the base surface and the reverse side of the floor tiles to carry out the actual operation of tiling.

7: When pasting the wall tiles, knead the floor tiles on the base surface, or use a rubber hammer to adjust the flatness of the wall tiles.

8: In order to ensure the flatness of the floor tiles, it is proposed to use a spirit level and a cross for tiling.

9: After the above process is completed, the cleaning is carried out, and the construction of stable wall tiles is carried out, and the joints are repaired after 24 hours.

1) The stirred tile adhesive should be used up within 2 hours, stirred every half an hour, so that it maintains good operability, and the cured tile adhesive is forbidden to be used.

2) 4-6 hours after construction. Subsequent surface construction (caulking) can be carried out, but vibrating machinery cannot be used to work on the construction surface.

3) This product contains cement and is weakly alkaline, if it accidentally splashes into the eyes, it should be washed with clean water or go to the hospital for diagnosis and treatment in time.

4) It is strictly forbidden to add water, cement, sand, any powder, etc. during the construction process.