How to master the car navigation installation method

If you do more homework and accumulate more, you will have more experience. Each car is different, how to pry can go online to check other people's installation tutorials. For the docking of the line, there is an instructional sign behind the general navigation.

The rear camera is generally integrated with the license plate light, and then find the reversing light after replacing this light. In short, we should practice more and learn more about online tutorials.

Hello, install navigation, you will not be able to go to 4S or professional modification factory to install, you need to change the line.

Find a master and learn from him for half a day.

As we all know, navigation plays an important role in long-distance driving. Many people will go to the 4S store when installing the navigation, and some people choose to install it themselves, so I will share the installation process with you. Car Navigation Installation Step 1:

There are two plugs in the back, disconnect the clamp and separate the wiring harness from the CD** machine. Car navigation installation step 2: install the GPS antenna Before installing the navigation machine, we first need to install the GPS antenna for navigation, place the antenna inside the platform from the co-pilot position of the car, and then place the GPS antenna vertically and stand on the far right side of the platform.

Stand up, because in this case the signal is the best. Car navigation installation step 3: navigation docking use it to navigate, install the original plug-in method, and navigation docking.

After docking, the long wire should be fixed with tape, which can prevent the wiring harness from colliding with the car when driving. Then, in the original way, tighten the screws and tighten the interior panels. This concludes the introduction.

How to install a car navigation system.

Remove the trim panel, unscrew the screws, and take out the CD player. Attach the GPS antenna for navigation, place the antenna inside the watch table from the passenger seat of the car, and place the GPS antenna vertically to occupy the far right side of the watch table. Remove the CD player, take it for navigation, install the original plug-in cable and navigation docking, and then screw the screws in the original way, and buckle the interior panel.

1. Remove the CD player on your car, if you won't disassemble it, look at the disassembly process of your own brand CD player at night, there are generally a few interior panels with screws, and you can see the screws when the interior panel is warped.

2. Use T20 to take down the four screws on the CD player, beware of the screws falling into the car during this process, the four screws ensure that there are at least three, and the screws play a fixed role.

3. After the screws are removed, gently take out the CD player, there are two plugs in the back, break the clip, and separate the wiring harness from the CD player.

4. Before installing the navigation machine, I should first install the GPS antenna for navigation, put the antenna inside the table from the co-pilot position of the car, and then put the GPS antenna vertically and stand on the far right side of the table. It is placed in a standing position because the signal is best in this case.

5. Take the original plug-in method to install the navigation and dock with the navigation, after the docking, the long wire should be fixed with tape, which can prevent the wiring harness from colliding with the car when driving.

6. Then according to the original way, screw it up again, and the interior plate can be buckled.

Car navigation installation is simple, you can power it through a cigarette lighter and then install the navigation module.

If you encounter similar problems in the future, you can follow the following ideas to solve them:

1. Finding problems: often living in the world, always in these kinds of contradictions, when some contradictions are projected into consciousness, the individual only finds that he is a problem, and asks to find a way to solve it. This is the stage where the problem is discovered.

From the perspective of the stage of problem solving, this is the first stage and the premise of solving the problem.

2. Analyze the problem: In order to solve the problems found, it is necessary to clarify the nature of the problems, that is, to figure out what contradictions there are, which contradictions, and what is the relationship between them, so as to clarify what results the problems to be solved, the conditions that must be met, the relationships between them and what conditions have been met, so as to find out the important contradictions and key contradictions.

3. Put forward hypotheses: on the basis of analyzing the problem, put forward hypotheses to solve the problem, that is, the solution that can be adopted, including what principles and specific ways and methods to take, but all of these are often not simple and ready-made, and there are various possibilities. However, putting forward hypotheses is the key stage of problem solving, and correct assumptions lead to the smooth solution of the problem, while incorrect and inappropriate assumptions lead to detours or lead the solution of the problem astray.

4. Verify the hypothesis: The hypothesis only proposes n possible solutions, and there is no guarantee that the problem will be solved, so the last step in problem solving is to test the hypothesis. In either case, if the test does not produce the expected result, a new hypothesis must be proposed and tested again until the correct result is obtained, and the problem is not solved.

There are many types of car navigation devices, among which the portable navigation device is more convenient to use, directly adsorbed on the windshield with a suction cup, and the navigation map is built-in, which does not need to be installed, and can be used when you get it. There is also a kind of on-board navigation, that is, by modifying the circuit and appearance of the car, a *** with navigation function is embedded in the car, which cannot be installed by itself and needs to find a machine manufacturer or car maintenance and decoration point.

You can go to a repair shop to install the car navigation, and don't install it yourself, so as not to damage the system and not use it.

Generally, there are several interior panels with screws, and the screws can be seen when the interior panel is tilted downward. Here we take the Tiguan as an example. 2.

Four screws or three screws are fine. Screws only play a fixed role. 3.

4.Before installing the navigator, install the GPS antenna for navigation, place the antenna inside the platform from the passenger position of the car, and then stand the GPS antenna upright and stand on the far right side of the platform. Stand up, because the signal is best in this case.

5.Use it to navigate, install the original plug-in method, and connect with the navigation. After docking, the long wire should be fixed with tape, which can prevent the wiring harness from hitting the car and making a sound when driving.

6.Then, according to the original method, tighten the screws and tighten the interior panels.

With the rapid development of life, cars have entered everyone's life, and we can't stop navigation when we travel. Therefore, it is very necessary to install navigation on the car. At the moment we don't need to go to the renovation shop to install the navigation.

At present, most of the navigation is basically plug-ins, which is not as troublesome as before. So how do you install a car navigation system?

How to install car navigation & mdash & mdash introduction.

If the CD** player in our car cannot be disassembled, take a look at the disassembly process of our own brand CD** player at night. Most of them basically have several inner panels with screws, and the screws can be seen when the inner panel is tilted downward. Here we take the Tiguan as an example.

Remove the four screws on the CD** machine with T20. During this process, be careful that the screws fall into the car. I think it's okay if they do fall. Four screws or three screws will do. The screws only play a fixed role.

Can tablets be used for car navigation: How to upgrade navigation?

1.The SD card must be backed up before upgrading.

In this case, you can still find the original one if the upgrade fails.

2.It depends on whether your navigation is portable or if you have a navigation installed in your car when you buy it.

If it's the former, it's very easy to deal with. If you can consult the places where you can buy navigation, most of the big brands basically upgrade for free forever.

If it's the latter, most of them are basically difficult to upgrade by themselves, so you can only buy a car or the map data of the car and then upgrade.

3.Knowing the model and brand you are navigating is basically useful for upgrading.

If you don't know, you can look it up on the Internet, or consult the person who sold your car.

If you know the model, you can check the latest electronic map online.

Then overwrite the entire map SD card folder under the root directory. If it's good for navigation, it works.

If not, there will be a lot of problems.

5.Know your computer literacy.

Do you know what the nouns are like path, root, batch file, executable, etc.?