If I change the administrator password, the original login password is admin, why is the system disp

You can't save a 6-digit password?

I'm also the same problem.,Modify the interface only with the original password、New password and confirm the new password,And the length is 6-15 digits,And the initial account password of the router is admin,Only 5 digits,How to solve it???

Press the reset key. From the new setting.

The default is admin, if you have changed the password, you can press the reset button on the router or if it is a hole, use a filament to top it, the router will be reset after a few seconds, all data is cleared, and the username and password are restored by default.

How to change the wireless password:

Make sure that the computer is connected to the wireless line, open the browser in the computer, and enter the IP address of the router in the browser address bar "Enter."

Enter the username and password (usually admin) in the pop-up router login box to enter the router.

Click "Wireless Settings" in the left column of the router settings screen.

Tap on "Wireless Security Settings" in the menu that opens.

In the wireless security settings window on the right, click 1 "WPA-PSK WPA2-PSK", and then click 2 "PSK password", you can enter or modify the wireless PSK password in the input box, and click "Save" at the bottom after you are done, so that the wireless network password is set or modified.

How to check the wireless password:

Knowing the password by looking at the wireless network properties, we open the Network and Sharing Center in the lower right corner of the computer.

Right-click on the connected wireless network and select Properties.

Click on "Show Characters" to see what the password is.

The wifi password is used when mobile phones, computers and other devices connect to routers. And the management password is what you need to enter the next time you log in to the router management interface after you set it. The default username of dlink is admin, the password is empty, and tplink is empty by default, and you need to fill in the password to ensure that others cannot tune your router.

These two passwords want you to go and separate.

The administrator password is 123456, and it becomes a reply.

That's what you set up yourself.

Maybe you changed the password and forgot it before, if you can set up the router, reset the router, press and hold the reset button for 15 seconds until all the lights are on, power off, and then power after half a minute.

admin is just the default. Some are administer by default, and some are cuadmin by default. In addition to defaulting, this thing can also be modified.

If you forget the username, you can press the reset button on the router or use the filament to top it if it is a hole, and the router will reset in a few seconds, all data will be cleared, and the username and password will be restored by default. At this time, you can enter it according to the username and password attached to the back.

It depends on which company's router it is.

That's whatever you set yourself, admin is the default.

It's the password you set earlier. Think for yourself, it should be your previous wifi password.

This password is set by you

The username and password are admin.

It may be that the user name is written incorrectly, the user name is generally: admin or administrator, or the password is mistyped or the password is empty, there is no need to enter, if this is not accessible, it can only be forced to unlock through the PE toolbox with a USB flash drive.

If the operation is correct, the administrator password is: admin, if the operation is not correct, of course, it is impossible to restore the factory settings. So the password can't be displayed correctly.

With a toothpick, poke into the recovery button, the indicator lights are all off, and then light up again, and the factory setting is successful. Then fill in admin and you're good to go.

Restoring factory settings is not to say that you can press it once, it will be fine, you need to press and hold for about 10s,

This router does not have an initial password. When you boot it up for the first time, you need to enter the 6-15 digit management password, which is the password for logging in to the router in the future. The password should preferably be a complex secret such as letters and numbers.

Hello, if you restore the router, the initial password of the router is generally on the reverse side of the router, you can take the router to see.

Look at the password behind you.

2.Press and hold RESET for ten seconds.

Hello, your situation is caused by the account policy --- password policy in the enabled local security policy, to solve the following method.

Enter the local security policy and enter "Enter" in "Run".

You have entered the local security policy, find the account policy --- password policy, click on the password policy, and 6 settings appear on the right.

Passwords must meet the complexity requirements --disabled, password length minimum --0, password minimum usage period --0, mandatory password history --0, restorable password storage --- disabled.

It's good to set it up.

This administrator password is self-set, and there is no original password, and even if there is, it may be 123456 or something.

admin is the login name and login password of the router, which is different from the administrator password.

The administrator password is mainly used to prevent others from logging in to their own router and adding a security number password, because the login name and password of the router are usually admin and not the password!

You should have already set an administrator password before.

The administrator password is set by yourself when you first enter the wireless router, and it is generally 6-15 digits.

If you forget your administrator password, if you can surf the Internet normally and you don't have to go to the wireless router settings page, then leave it alone.

If you urgently need to enter the wireless router settings page, then factory reset the wireless router, and then set the administrator password when entering the settings page. In that case, you'll have to reset your wireless router.

How to be a wireless router, do a factory reset, and reset the login password. This password has been changed.

6 to 15 is a cryptographic mechanism...

There is a default password written on the back of the router, not necessarily admin

You should be the router background.,The password doesn't have to be admin.。 Hope you can adopt thanks.

This is not admin, you press the factory settings key, and then see what the password under the router is.

That's the original password for your wifi, and you have to enter the password you just set up anyway.