What is the problem with the Samsung fully automatic washing machine display 1E?

If the washing machine has faults such as "1e", "3e", "6e", "7e", "8e", "9e1", "9e2", "13e", "he", "pe", "inverted fe", "oe", "fe", "he1 he3", "te1 te3", etc., it is recommended that you unplug the power plug of the washing machine, wait for 10 minutes to power on again, and then observe. If the error still occurs after powering on, you can apply for repair through Samsung's official website, and the engineer will come to your door to deal with it.

It should be a frequency conversion board (double board), usually the protection is in the water level sensor, safety switch and motor speed sensor, etc., that is, at the lower right of the frequency conversion board at the output of the cable, if not these are the frequency conversion board problems.

You can sense if the temperature near the motor is too high.

If the connection cable is not short, the water level sensor is faulty, and the connection is dirty, and the computer board will not be able to sense it.

Samsung automatic washing machine shows 1e fault**, it may be a bad water level sensor or poor contact with the computer board, please operate as follows:

1. First power off the machine for more than 10 minutes and restart the test machine;

Hello dear, 1. Check the motor [fault cause]: Sanyo washing machine ED1 is very likely to have an abnormal motor and cannot work, it may be that the motor is damaged, or it may be that the coil is burned, the reason for the motor to burn out is that the load is too much due to too much laundry, the water level is too high and the water level is too high to cause overflow, etc. [Handling Method]:

After disassembling the motor, check whether the motor is normal, if the coil is burned, or the motor is not working properly, the motor needs to be repaired or replaced. 2. Check the inverter board [fault cause]: If the inverter board fails, ED1 fault will be reported through it, the reason is that the burning of the motor will cause problems with the inverter board connected to it, so you also need to check the inverter board when checking the motor.

Solution]: Measure the yellow, white and blue lines connected between the frequency conversion board and the motor, and confirm whether it is burned or broken, and replace the variable frequency board and connecting wires if there is. 3. Check the communication line of the main control and frequency conversion Zheng Li chip [fault cause]:

There is a problem with the communication line between the main control chip and the inverter chip, which will cause the ED1 failure of the Sanyo washing machine. [Solution]: Open the main control board, check whether the inverter drive chip is abnormal, if necessary, use a screwdriver to clean the glue on the surface, and then determine the specific cause and repair.

First, the Samsung automatic washing machine shows 1e failure**, which may be due to poor water level sensor or poor contact with the computer board.

Second, the fault handling method:

1. First power off the machine for more than 10 minutes and restart the test machine;

Hello boss, the Samsung drum washing machine sometimes displays 3e when washing The reason is as follows: The Samsung drum washing machine fails 3e reason: The water level of the washing machine does not reach the 1st gear water level in 30 minutes during the water intake process, and the water level does not reach the set water level in 20 minutes.

Samsung drum washing machine fault 3e solution: 1. Check the water inlet valve and whether the water pipe is dirty and blocked. 2. Check if there is no water in the faucet.

3. Check whether the water pressure is too low. 4. Check whether the water level switch in the washing machine is installed in place. 5. Check whether the water level switch of the washing machine is damaged.

Summary. Dear dear, it's a pleasure to answer your <>

The reason why the Sanyo washing machine shows ED1: The reason why the Sanyo drum washing machine has ED1: The motor is abnormal, the motor of the washing machine cannot be started, and the motor is generally burned.

The reason why the washing machine motor is burned: the washing machine is used as the power to drive the washing wheel, drum or spinning bucket to run regularly by the AC single-phase motor. Generally, the main reasons for motor burnout are:

1.Excessive load: The power of the washing motor is determined according to the rated washing capacity of the washing machine and the efficiency of the motor, and there is room for it.

However, when the weight of the washed dry laundry exceeds the rated capacity, the load on the motor increases, the temperature rises, and finally the motor windings burn out. <>

<>2.Prolonged overflow (exceeding high water level) may also cause the motor to overload and burn the windings. Solution: Replace the MPU <>

<> Sanyo washing machine shows what is the reason for ED1.

Dear dear, it's a pleasure to answer your <>

The reason why the Sanyo washing machine shows ED1: The reason why the Sanyo drum washing machine has ED1: The motor is abnormal, the motor of the washing machine cannot be started, and the motor is generally burned.

The reason why the washing machine motor is burned: the washing machine is used as the power to drive the washing wheel, drum or spinning bucket to run regularly by the AC single-phase motor. Generally, the main reasons for motor burnout are:

1.Excessive load of negative trousers: The power of the washing motor is determined according to the rated washing capacity of the washing machine and the efficiency of the motor, and there is room for it.

However, when the weight of the washed dry laundry exceeds the rated capacity, the load on the motor increases, the temperature rises, and finally the motor windings burn out. <>

<>2.Prolonged overflow (exceeding the high water level) may also cause the electric mold to overload the local machine and burn the windings. Solution: Replace the MPU <>

<> dear, expand the information here<>

<> Sanyo washing machine disassembly and cleaning method: Step 1: First of all, turn off the power switch, open the cover of the washing machine, see two rivets on the left and right sides to fix the lid of the washing machine and unscrew it, after removing the screws, the two plastic rivets are removed with a screwdriver, and the raised blades in the washing machine barrel can be taken out.

Step 2: After opening the upper cover, you can also open the upper cover of the round washing machine to clearly see the 4 solid hole pure screws, unscrew it, you can lift the upper cover, you can easily remove the inner cylinder cover, the upper cover can not be completely removed because there is a lack of water, orange pipe and wire are connected in this place, at this time, it should be noted that the upper cover can not be completely removed, can only be slightly turned back and placed against the wall, and then lift the upper cover of the washing machine. <>

<>Step 3: Remove the screws of the washing machine and take out the stainless steel inner cylinder of the washing machine. Step 4:

Then clean the inner wall of the washing machine thoroughly, generally this inner wall will be very dirty, and it is necessary to clean it well Step 5: Take the stainless steel barrel of the washing machine aside to clean it. Step 6:

Then put the cleaned stainless steel barrel back in place and put the screws on well. Step 7: The next step is to install the lid of the washing machine, which is the same as the removal step, and put the screws on.

Summary. Sanyo washing machines displaying ED1 usually indicates that the electronic door lock is faulty. This can be caused by a broken door lock, faulty wiring, or faulty circuit board.

We recommend that you perform the following steps:1Check that the door is closed and closed completely.

If the door is not fully closed, the door should be closed completely. 2.Check that the door lock has not been damaged or deformed in any way.

If yes, the door lock should be replaced. 3.Check if the wiring associated with the door lock is damaged or detached.

If so, the line should be repaired. 4.If none of the above steps resolve the issue, you may need to replace the electronic control board.

Please note that due to the high voltage electrical part, it is recommended that you do not carry out repairs and replace parts yourself if you do not have the relevant repair skills and expertise. It is recommended that you contact Sanyo after-sales service center or professional and technical personnel for inspection and repair.

Sanyo washing machines displaying ED1 usually indicates that the electronic door lock is faulty. This can be caused by a broken lock, faulty wiring, or a defective circuit board. We recommend that you follow the steps below:

1.Check that the door is closed and closed completely. If the door is not fully closed, the door should be closed completely.

2.Check that the door lock has not been damaged or deformed in any way. If yes, the door lock should be replaced.

3.Check if the wiring associated with the door lock is damaged or detached. If so, the line should be repaired.

4.If none of the above steps resolve the issue, you may need to replace the electronic control board. Please note that due to the incarnation to high-voltage electrical part, it is recommended not to carry out repairs and replace parts yourself if you do not have the relevant repair skills and expertise.

It is recommended that you contact Sanyo after-sales service center or professional and technical personnel for inspection and repair.

If it doesn't work for a long time, it may be a problem with the water. Is it?

Not using it for a long time is unlikely to cause the ED1 error** to appear. If you suspect that the water source is the cause, it is recommended to check that the faucet is open, that the water pressure is normal, and that the washing machine's water inlet valve is clogged. Hall of Relatives

The Sanyo washing machine shows an error caused by the failure of the Level Sensor**. The level sensor is a device inside the laundry machine, which can detect the water level and prevent water from overflowing; Its job is to measure the amount of water in the sink and solve the problem based on the measurement results, so when we use water in the washing machine, the level sensor is responsible for feeding back the situation to the washing machine circuit board, so that the circuit board can adjust the control of the water according to the change in water level. Because the level sensor of the washing machine may malfunction, the most common reason is the failure of the internal circuit inside the level sensor, the filter screen of the level sensor is blocked, resulting in too many invalid bytes read by the level sensor, or the temperature is too high.

When the washing machine has an ED1 error, the first thing to do is to check whether the lamp is reliable, and when replacing the temperature sensor, make sure that the liquid level sensor is in a cool environment, if the lamp is not reliable, you can try to replace the lamp with a new one, in order to ensure that the liquid level sensor is working properly. If a faulty circuit inside the level sensor is found, the circuit should be tested with the relevant tools, the cause of the fault should be determined, and the necessary measures should be taken to repair it. Finally, check the filter screen, because the filter inside the level sensor may be clogged with dirt, which will cause the measurement results of the level sensor to change, so that the washing machine has an ED1 error, if it is found to be clogged with dirt, you need to clean the filter screen in time and replace it with a new filter screen to ensure that the leakage of the level sensor works properly.