How to fill the automatic washing machine, how to put water in the automatic washing machine

The steps are as follows:

1.Plug the power supply of the automatic washing machine into the 220V household power supply, and then click the power button of the washing machine, and listen to the sound to prove that the laundry has been powered on.

2.Click on the program, according to the program button to select the cleaning method up and down, to choose fast washing as an example, the operation effect is as follows.

3.After choosing the program, adjust the water level with your own clothes and the amount of things you need to wash, select the water level, and choose up and down according to the water level button.

4.Choose the appropriate composition, soaking-washing-rinsing-dehydration and other functions, choose well, such as in the laundry process does not need to dehydrate, etc., the LED lights up to perform the function behind the lamp, and the operation is as follows.

5.Turn on the faucet, click the start pause button, so that the automatic washing machine starts to release water and start washing clothes, and the buzzer will sound when the washing is completed.

The back of the washing machine has a water pipe. Connected to the faucet, you need to open the faucet to fill the water, and then click the start button of the machine. It is a program-controlled press of the start button, and some models will directly enter the water.

There are also some models that the wave wheel rotates left and right a few times before entering the waterIf you add water manually, it will also rotate if you add enough water. It doesn't affect the machine, but it's inconvenient.

Don't let the water flow to the computer board, that's fine. About 15 minutes. Add 1 or 2 more waters.

It is water for rinsing.

Correctly connect the water inlet pipe of the washing machine, turn on the faucet after the machine is turned on, and the washing machine will automatically feed the water by itself at the time of the water inflow, without manual assistance.

Either the computer board is broken, or the inlet valve is broken, or the line between the computer board and the inlet valve is off. Generally, the inlet valve is more broken. If you don't repair it, you can only add water manually, but the rinsing function is gone.

Automatic washing machine manual water discharge operation method:

1. The washing machine should be powered on first, you can press the power button of the washing machine to try it, "drip" sounds, and it is on, it means that it is powered on.

2. Press the "Power" button to keep the washing machine in a state of preparation, and there should be no water on the surface of the washing machine.

3. Find the "program" column, because different washing machines, the program is in different positions, but the handwriting reminder is the same.

4. In the program column, find "dehydration", and then press the program button, when which one is on, the washing machine will start that work, when the "dehydration" is on, it's OK, don't press the program button.

5. Press the start button to pause, the washing machine is not rotating at this time, so press it to start. Let's press it, and that's when the washing machine starts draining.

6. When the water in the washing machine is drained, the washing machine will pause for about five seconds, at this time press the start pause button, at this time the washing machine will stop working, and the drainage will be completed. Finally, press the "Power" key to turn off the power.

Take Haier washing machine as an example, there is a water pipe behind the machine cover of the automatic washing machine, which needs to be connected to the faucet, when using the washing machine, you only need to set the program, press the start button, and keep the faucet open throughout the whole process, the machine will automatically control the water inlet valve, and it will automatically replenish water when it needs to enter the water, without manual operation.

Proper use of a fully automatic washing machine:

1. First of all, prepare the clothes to be washed, wash the dark and light-colored clothes separately to avoid dyeing;

2. Put the clothes in the washing machine and add an appropriate amount of laundry detergent;

3. Cover the cover plate of the washing machine, connect the water pipe to the faucet, and turn on the faucet;

4. Turn on the power, press the start button, set the water level, washing method, etc. on the washing machine panel, press the start pause button, and then you don't need to care, the automatic washing machine will automatically enter the water, wash, drain, dehydrate, etc. according to the set program, and there will be a prompt sound after the end;

5. Finally, open the lid, take out the clothes to dry, and turn off the faucet and power.

This answer applies to most washing machine models such as Midea, Gree, and Haier.

Taking Haier washing machine as an example, the water filling steps of the fully automatic washing machine are as follows:

1. Plug in the power first, and then click the power button on the washing machine;

2. Click on the program and select the cleaning method up and down according to the program button;

3. Select the water level, turn on the faucet, and click the start pause button, so that the automatic washing machine will automatically fill the water.

How to install the water inlet pipe in a fully automatic washing machine:

1. Press down the slider on the inlet pipe fitting of the automatic washing machine and one end with the inlet pipe joint to separate the water inlet pipe joint from the water inlet pipe.

2. Separate the connecting seat from the water inlet pipe first, hold the connecting seat on one side, and hold the buckle on the other side to pull it down.

3. After connecting the steps of the automatic washing machine, then tighten the plastic interface nut until there is no leakage.

4. Connect the other end of the water inlet pipe with the water inlet of the automatic washing machine, tighten the plastic nut, and open the faucet directly after the installation is completed. At the same time, pay attention to rotate the lower connector until the upper and lower connectors are tightened, press the buckle of the water inlet pipe down, insert the water inlet pipe into the lower connector up, and then loosen the buckle to check whether there is water leakage, if there is water leakage, it needs to be reinstalled to complete the operation.

This answer applies to most washing machine models such as Midea, Gree, and Haier.

Summary. Hello. The automatic washing machine is used to manually add water, that is, it does not automatically fill water through the water inlet solenoid valve.

When using a fully automatic washing machine with water manually, set the position of the water level switch (high, medium, low) and the laundry program only.

Put the clothes and washing liquid into the laundry bucket, use the faucet or bucket to add water to the laundry bucket, when the water level is reached, the water level switch will send an electric signal, and the automatic laundry will start.

When the washing time is up, the washing machine will stop automatically.

In this way, it is possible to wash multiple times with the washing water added at one time. Hope mine can be helpful to you.

How to make a fully automatic washing machine only fill with water and not wash.

Hello. The automatic washing machine is used to manually add water, that is, it does not automatically fill water through the water inlet solenoid valve. When using a fully automatic washing machine with water manually, set the position of the water level switch (high, medium, low) and the laundry program only.

Put the clothes and washing liquid into the laundry bucket, use the faucet or bucket to add water to the laundry bucket, when the water level is reached, the water level switch will send an electric signal, and the automatic laundry will start. When the washing time is up, the washing machine will stop automatically. In this way, it is possible to wash multiple times with the washing water added at one time.

Hope mine can be helpful to you.

I want to clean the washing machine, but the fully automatic washing machine can't just put water.

Yes, dear, a fully automatic washing machine can't just put water, you can only add water manually.