I have a network cable at home that was pulled over, and now I want to take more than one handheld

Ha, take a good look at the manuals of the router, which is written in great detail.

There should be 3 network cables, one is pulled by you, connected to the route, one is connected from the route to the desktop, one is connected from the route to the portable, if you don't know how to set the IP, then you can automatically get the address, if you can set the IP, they need to be in the same network segment, and the network segment can ask the family who pulled the network cable.

Routing doesn't require much setup, and if one can work, the other will definitely work too.

This is very detailed, you just need to follow it.

Yes, just set up the route!

Follow the wireless routing setup wizard to set the account password

First of all, your router and the access network cable are not in the same IP segment, the network cable from the neighbor's house is connected to the WAN port of the router, set static IP access on your router, input, and then the gateway, DNS, fill in according to the actual situation. It's best to give wireless encryption.

The network cable you pulled from others, you can say that it is the network cable, it means that it has been converted from optical fiber to twisted pair signal, so what equipment is it separated from others??? This is very important, and the settings and wiring of the corresponding equipment are different.

1. Router reset.

2. Enter the router setting interface, in the WAN port setting column, enter the account number and password of the optical fiber given to you by the person who came to pull the cable. Set up router auto-dialing.

3. The incoming line is connected to the WAN port of the router, and the two portable phones are connected to the LAN port of the router respectively.

4. The two portable devices are set to automatically obtain IP and DNS.

1. Router reset.

2. The incoming line is connected to one of the LAN ports of the router, and the two portable phones are connected to the other two LAN ports of the router respectively.

4. The two portable devices are set to automatically obtain IP and DNS.

If the IP address is not right, change the local IP to the IP on the back of the route.

Judging from your description, it should be that the operator who provides the network binds this line to your computer, and it is estimated that it is bound according to the MAC address of your computer, so it will cause other computers to be unable to use this line to access the Internet, and the router cannot directly connect to the Internet.

1. Enter the command line mode on your computer, run a command ipconfig all, find the MAC address of your wired network card from the displayed message, and copy this address down.

2. Connect your computer to the router, log in to the router settings page, and change the MAC address of the router to the MAC address of your own computer. (Most routers support changing their own MAC address, please check the router's manual for specific operations, and change your computer's MAC address if necessary to avoid conflicts caused by duplication of the two MACs).

3. Connect the network cable with the router after modifying the MAC address, and other computers and mobile phones are connected to this router.

The general principle is to modify the MAC address of the router to make it the same as the MAC address of your original computer, so as to bypass the MAC address binding problem. Of course, there may be some details, such as whether the DHCP (IP Address Assignment) service is provided by the router or directly by the network operator, which needs to be tested to determine.

If you don't find an official network cable by yourself, it's in an ordinary operator, such as the kind of 50 yuan a month, then he has set his own router to prohibit secondary routing to sign in, so it can only be used by a single account and a single computer!

Wired connection: Prepare a 20-meter, pressed crystal head network cable.

Prepare a short network cable about 2 meters to connect the cat and the router.

Setup of normal adsl cats and routes:

1 The home network cable or the network cable out of the cat must be connected to the WAN port of the wireless router 2 You must use a wired computer, the LAN port of the wireless router, turn on the power, and log in to the management page of the bottom label IP address such as 192... type, enter your username and password, enter the page, and start the setup.

3. Select PPPoE or ADSL dial-up mode for the WAN port, enter the username or password provided by China Telecom, China Unicom, or broadband carrier, and select Auto Connection.

4 DHCP function is on.

5 Wireless Setup.

Radio Broadcasting: Checked.

Enable SSID: Select this option.

SSID number: English or pinyin (kanji is not acceptable).

Channel: Automatic.

Mode: 11BGN Mixed Band Bandwidth: 20MHz

6 Wireless security settings.

Select: WPA-PSK WPA2-PSK

PSK Password: Make it up yourself.

6 The computer must be set to automatically obtain the IP address and DNS server7 After restarting the route, find the signal and enter the above password to log in to the wireless WiFi

The easiest way is to change the router directly to a wireless router, and then equip your computer with a wireless receiving module, the cost is about 200, so that you don't need to pull the wire, because at home to pull the wire, the bare wire is more ugly, and it is generally buried in the wall when decorating.

If you can pull the network cable, it is recommended that you still pull the network cable, it is not possible to use wireless, unless you often do not close the door, as long as you close the door, the wireless will be very weak.

The cat is connected to the router (limited or wireless) router LAN port 1 is connected to the computer LAN port 2 is connected to another computer It is best to connect to the limited If it is unlimited, the signal is not very good Unstable, and if there is wireless, there must be a wireless receiver It is not very expensive More than a dozen dollars Choose by yourself Each has its own advantages and disadvantages.

Connect the right router to two network cables, and then connect it to two computers.

In getting two wires, put the original line plug route, and set it up to connect the two wires to the computer. It's the best wireless router. No need to pull the network cable.

I feel that it is more convenient to use wireless, and pulling such a long network cable at home destroys the beauty.

There are usually two ways for secondary routers:

1. AP mode:

You only need to change the LAN port address of the wireless router to an infrequently used one (for example, change it to avoid conflicts, disable DHCP, enable wireless-related functions, and then insert the line from the main router into the LAN port).

The computer connected to it is wireless or wired, and it is connected to the Internet in the same way as if it were directly connected to the main router.

2. Routing mode:

Change the LAN port address of the wireless router to another network segment (for example, if DHCP and wireless related functions are enabled, the WAN port uses a dynamic IP address or a static IP specified by the main router.) Insert the line from the primary route into the WAN port.

The computer connected to it uses a dynamic IP address or a static IP address in the network segment to access the Internet.

The first router connected to the cat is set to PPPOE mode, and the second router is set to dynamic mode, and the IP address of the second router should also be changed.