What do you do to make a small production more personal? What s the little production?

Small production simple and beautiful production method:

Simple marshmallow catapult handmade.

All you need to make a marshmallow launcher is: 4 large marshmallows, 7 bamboo skewers, a thin rubber band, a plastic spoon and duct tape.

1.The production was so simple that my 4-year-old was able to build it himself.

2.Directions: Use 3 marshmallows and 3 bamboo skewers to form a triangle.

Use 3 more bamboo skewers and 1 marshmallow to form a pyramid. Tie the plastic spoon securely to the end of another bamboo skewer. Tie a thin rubber band to the top marshmallow.

Thread the spoon through the rubber band and insert one of the base marshmallows.

3.Kids can play with its marshmallow launcher as soon as they're built, but they do so gently so they don't tear the marshmallows. It can be difficult for a child to keep it soft, so I recommend that after making the catapults, let them sit for the rest of the night to make the marshmallows hard and stronger, allowing for a stronger launch.

4.Note: You can also keep marshmallows in a bag for a day to make them a little harder before using them to make a marshmallow catapult.

DIY Glitter Glitter Nail Polish Key Hand Makeover Tutorial.

Materials: adhesive tape, nail polish, pins, toothpicks;

Production Steps:1Clean the keys first. Rubbing alcohol is very useful for this. Let them dry.

2.Now, bend your pin to create a "V" shape and stick it to the edge of the surface. This will be the hook that hooks your key to dry.

3.Use tape to separate the part to be painted from the handle.

4.Next, apply nail polish to both sides of the key. You may need to add more than one layer of polish.

5.Now, place the key on the hook and let it dry.

6.When the keys are half-dry, apply a second coat of nail polish. Put it back in and let it dry completely.

You can make a turtle that can sweep the floor, there is a shoe brush, grind off the handle of the shoe brush, press the motor on the car on it, and then glue the cake pan on it, make a little decoration, start the motor, and the little turtle will go!

Prepare the materials and tools for making the sand table: chassis, tracks, paints, grass powder, turf, silicone guns, waste newspapers, white glue, plaster, etc.

If required, you can design the shape and height of the track yourself and put it together with hot silicone. (Note: It must be glued firmly, not loose or tilted).

Glue masking paper on the track to prevent debris from entering during the production process and should not be removed. Use waste newspaper to create a pre-designed shape, which can be fixed with masking paper, then covered with a plaster bandage and sprayed with water.

Once the basic shape is fixed, plaster is poured to make the shape stronger and easier to color. (Note: Be careful to avoid the track when pouring plaster).

Glue the building to the mold that has already been made.

Coloring, coloring is to pay attention to painting dark colors first, then intermediate colors, and finally highlights, weathering effects, and then planting vegetation.

After planting vegetation and sprinkling grass powder, the simple sand table is basically completed, and finally don't forget to hit the track with sand skin, and it is done.

Make a Kong Ming lantern!

It can fly on its own!

Sourcing and making.

Take a large, very thin plastic tote bag and cut it flat at the handle.

Take a thin copper wire about 60cm long (you can use one of the copper wires in multiple strands of soft copper wire), and tie the two ends on both sides of the pocket mouth.

Choose a place where there is no wind (or indoors), pinch the bottom two corners of the bag with one person and two hands, so that the opening is facing down, and the thin copper wire wrapped with cotton will naturally sag. Then pour an appropriate amount of alcohol on the cotton, ignite the alcohol, and after dozens of seconds, the Kong Ming lantern will rise in the air.

Note that the alcohol cotton should not be too heavy, and the total mass (the total mass of convenience bags, fine copper wires, and alcohol cotton) can generally be made easier to take off below 5g.

The length of the fine copper wire should be appropriate, so that the alcohol will not melt the plastic bag after burning, and pay attention to prevent fire.

If you want to pull it down, you can tie another thin copper wire in the middle of the thin copper wire to make it droop beforehand.

A match and a large needle are put together, wrapped tightly in the aluminum foil of the cigarette pack, and the aluminum foil at the end of the match head is bent over and tightened. Then attach a directional tail near the tail and pull the needle out, and it becomes a very simple recoil rocket.

During the experiment, a small rocket was placed on a wire stand, a match was lit, and the part of the aluminum foil tube wrapped in the match head was heated. When the temperature rises to the ignition point of the match head, the matchbox in the foil is ignited, causing the surrounding air to expand dramatically, and the gas is ejected from the tail mouth at high speed. As a result of the recoil, the bazooka flew forward from the rack.

If you wrap two head-to-head matches in aluminum foil, leave them unclosed at both ends. Place it on top and heat it from the middle. When the match in the barrel is lit, the gas is ejected from both ends, and the foil cylinder remains on the rack, thus indicating the conservation of momentum in the system.

Use plastic bottles to make indigo.

Materials required: plastic bottles, scissors.

Specific steps: 1. Use scissors to cut the plastic bottle, and pay attention when cutting. Try to start with a third of the way through. The tapered side is not to be left, leaving the bottom part.

2. Then start sorting out these thin strips. Pay attention to cut vertically, cut into thin strips of equal width, and stop when you cut to the position of the pattern.

3. When these thin strips are pressed outward, pressed into the shape of petals and begin to weave flowers, press down the thin strips, and buckle the bottle body downwards to cut out the ears.

4. Arrange the cut thin strips neatly and fold them inward (you can weave some shapes according to your preferences) 5. After weaving, a flower basket is ready (you can paint the color on the bottle body, or graffiti).