How to install the router, how to install the router I want the whole process, thank you

Router configuration steps (factory reset of router is recommended):

The WAN port of the router is connected to the network cable of the broadband modem.

The LAN port of the router is connected to computers, TVs, and set-top boxes.

Assuming that the cat does not have a router, the router should be set to "PPPOE dialing", use the account number and password given when handling broadband, and pay attention to distinguishing between "uppercase and lowercase letters".

The local connection of the computer is set to "Automatically obtain IP address, automatically obtain DNS server address".

The computer can no longer dial up, and if there is a broadband connection, be sure to disable it.

Plug in the power supply, plug the network cable provided by the broadband to the LAN port, and insert another network cable to the computer.

There is an IP address on the back of the router, and there is a setup wizard after entering the IE address.

Reset the router: Find a small hole or button labeled REST (or guest) on the router, poke it with a toothpick for more than 5 seconds, and go back to factory settings.

How to connect and set up the router: Connect the computer to the LAN interface of the router with a network cable, and set the router as follows:

1. Log in to your router (enter or log in in IE, enter the username and password, and the router label is there.) Usually admin).

2. Go to the "WAN" setting

A If your broadband is to have an account password, set up PPPoE, fill in the account password, select Automatic connection as the connection mode, and confirm that if your carrier will be bound to your computer, choose to copy the MAC address of the terminal.

b If you don't need the account password, if you are given a fixed IP, please select a fixed IP address and fill in the correct address of the fixed IP address, mask, gateway, and DNS.

c If you don't need the account password and it is a dynamic IP address, please select a dynamic IP address and fill in the DNS address.

3. Go to the wireless settings, select WEP or WP2-PSK, set the wireless password, and remember this password.

4. Go to the "DHCP" settings and activate the DHCP server.

5. Set "LAN IP" to, remember to use this IP to log in to the router in the future, and save it after setting.

6. Connect the broadband network cable to the "WAN" port of the router, and connect the computer to one of the "LAN" ports of the router.

7. The computer is set to automatically obtain IP address and DNS address.

Computers, mobile phones, and wireless devices should be able to access the Internet.

If there is no wireless function, ignore the wireless part.

The most accurate whole process must refer to the router's manual, combined with your network and your needs to set him up.

The general setup steps are:

Connection: (refer to the router manual).

The final network cable of the network ** provider is plugged into the WAN end of the wireless router (no network cable is plugged in when set), and the network cable of all computers is plugged into the LAN end of the router.

Settings: (refer to the router manual).

1.Remember the settings of the business to you, and if you can't remember it, you can ask them; Use these parameters to set the WAN side of the router.

2.Configure the LAN side of the router: Enable DHCP service.

3.Set the WLAN side of the router: Set the password, which is generally safer to use WPA now. Remember the name of the outgoing signal from the wireless router, and the password for backup.

4.Check whether the gateway address of the final network cable of the network ** provider is the same as your wireless router address, if it is the same, please change your router address, for example, you can change yours.

5.Set all Internet devices to get addresses automatically.

That's basically it, remember: the WAN setting method is determined by the network cable plugged into the WAN side, and the WLAN setting password is up to you.

Thank you for your question.

Correct connection - enter the router address in IE (on the router nameplate or manual) - enter the router username and password (on the router nameplate or manual) - follow the steps of the setup wizard to choose your Internet access method - enter the username and password address given to you by the network ** provider, etc. Follow the steps in the setup wizard and click Next until you're done.

Hello, please install 360 computer expert, enter in the question input field: how to install the router.

Hello! The steps to install and set up the router separately are as follows:

1. First of all, after connecting the wireless router, you need to check whether it is powered on and whether the wireless router is running normally.

2. After checking that it is correct, check the instructions on the bottom of the router, open the browser and enter the router IP, and then press Enter to enter, at this time a dialog box pops up, you need to enter the account name and password, there will be at the back of the router, in general: account name: admin password:

admin。

3. After entering the password behind the router, you can log in to the settings page of the router.

4. Click on the setup wizard on the page and follow its requirements step by step.

5. Click Next to enter the account password setting, this account password is the account password of the current network network, if you don't know, you can consult the network operator.

6. After setting the account and password for surfing the Internet, the function of wireless Internet access is set, set the wifi name and wifi password, it is recommended that the password is not too simple, it is easy to be cracked, and the encryption method can be recommended by the system.

7. Click Done, restart the router, and the settings have been successful.