What happens when I turn on the air conditioner at home, and when I turn on the air conditioner in m

If the air conditioner of the two of you is turned on at the same time, the main switch knife is likely to jump because the empty switch of the main switch is small, or check the total zero line of the two of you, whether there is any loosening phenomenon?

This situation is likely to be caused by the low allowable load of the main power switch of the residential building where the two residential buildings are located, and the property management department should be advised to replace the power main gate of the whole building.

If the neighbor's house turns on the air conditioner, and my house turns on the air conditioner, both of them trip, which means that the voltage is unstable, and the instantaneous current is too large.

If your neighbor's house turns on the air conditioner, and your house turns on the air conditioner, and both of them jump the gates, then there may be a problem with your main circuit.

That's why the load on the two of you is a bit heavy, so the main gate is disconnected! You need to change the line or switch it!

Hello, the biggest possibility is that your building is designed with wires squared too small to meet the voltage requirements. It is advisable to have a professional replace it.

Your neighbor's house turns on the air conditioner, and your house turns on the air conditioner, and both air conditioners trip, because the two of you are walking on a wire, and the wire's line is in line with the overload, so it trips.

If the two of you turn on the air conditioner, we will all jump, not because your air switch is unqualified, but because the air switch or fuse capacity under the main gate is too small.

The neighbor's house turns on the air conditioner, and we jump when I turn on the air conditioner in my house, what's going on? This is because the number of empty amperes used by the two of you is too small, and the starting current of the two at the same time is large, so the switch jumps.

Both of them are tripping because your power load is too large, which leads to the appearance of this kind of jump explosion is also generally overload protection.

This is due to the fact that the load on the air conditioner switch is too great. That's why you can jump when you smash it, and you can change the air switch to a more powerful one.

Then it may be that the circuit here is unstable, so when the two air conditioners are used at the same time, the circuit load is large, so it will automatically trip.

The neighbor's house turns on the air conditioner, and your house also turns on the air conditioner, and the moon of the two families jumps? What's going on? Maybe it's because both of you turn on the air conditioner, and then you use too much power for electricity, so the gate knife jumps on its own.

This situation should be that a switch is shared, and the power is high, causing the main switch to trip.

It's because the air switch between the two of you has a small limited current.

It is recommended that you switch to an air switch of about 30A (for an air conditioner).

Hello, it is recommended to check whether the distribution box is connected incorrectly, if it is two air conditioners overloaded, the jump must be the main switch.

The neighbor's house turns on the air conditioner, and as soon as you turn on the air conditioner, both gates jump, maybe the power is too large or check the electric switch.

Prove that maybe the two of you are connected together, and the fuse may be broken.

Hello, the neighbor and your home turn on the air conditioner at the same time, and the brake of the two families can be replaced with a large number of protectors at the same time.

The neighbor's house turns on the air conditioner, and as soon as my house turns on the air conditioner, both of them will trip? It is recommended to ask the State Grid to send engineers to provide door-to-door service, is it a problem with the lines of the two companies?

The trip must have nothing to do with the neighbor's house.

Hello, that should be an overload caused by too thin wires.

First, the cause of the failure.

1. Overload. If the power consumption is too large or there is a short circuit, the protection device of the electric switch trips.

2. There is leakage of electrical appliances or lines, or people touch the potato imitation wax electricity, the current is directly into the ground without the zero line, and the electric switch perceives the leakage and the protection device trips.

Second, the solution.

1. Check the grounding wire and the neutral wire, and connect the ground wire with the neutral wire; Replace the capacitors of the compressor; Use a coarse-pointed, dedicated air-conditioning cable; Replace the leakage switch.

2. Adjust the knob on the temperature controller to the required position and adjust it according to the temperature required by the air-conditioned room.

3. Let professional maintenance personnel deal with it.

The reason why two air conditioners trip may be due to the leakage and short circuit of one of the air conditioners or the air conditioner line, or the circuit load cannot support the operation of the two air conditioners.

Tripping refers to the breaking of the electric switch. There are generally two reasons for tripping:

1. Overload. If the power consumption is too large or there is a short circuit, the protection device of the electric switch trips.

2. There is leakage of electrical appliances or lines, or people touch electricity, and the current directly enters the ground without the zero line, and the electric switch senses the leakage and the protection device trips.

When two air conditioners are turned on at the same time at home, the nucleus tripping may be due to one of the following reasons:

1.Circuit overload: Two air conditioners running at the same time will consume a large amount of electrical energy, and if the circuit load is close to or exceeds the rated load capacity of the circuit, it will cause tripping.

This may be because your circuit can't carry the power demands of two air conditioners at the same time. It is advisable to check the electrical capacity of your home to ensure that it can meet the power needs of running two air conditioners at the same time.

2.Short circuit: If there is a short circuit in the circuit you dig in the hall, turning on two air conditioners at the same time may cause a short circuit in the circuit, which in turn will cause a trip.

A short circuit can be caused by a damaged wire, faulty electrical equipment, or poor wiring. It is advisable to see a professional electrician for inspection and restoration.

3.Aging or faulty circuits: If your home's circuitry is aging, poorly contacted, or otherwise faulty, turning on two air conditioners at the same time may trigger circuit issues that can cause tripping. In this case, it is recommended to find a professional electrician for maintenance and repair.

4.Fuse or circuit breaker issues: A fuse or circuit breaker in a home circuit may not be able to withstand the load of two air conditioners running at the same time, causing tripping. Check that the fuse or circuit breaker is rated and working properly, and if there is a problem, it needs to be replaced or repaired.

There are several reasons why two air conditioners trip when you turn on two air conditioners at home:

1.Insufficient circuit capacity:If the wires and switches in your home can only withstand the electrical load of one air conditioner, then turning on two air conditioners will exceed the tolerance range, resulting in short circuits and trips.

2.The power of the air companion is too large:If the power of the two air conditioners is greater than the capacity of the circuit, then it will also cause tripping.

At this time, it is necessary to check whether the power of the empty Li ridge adjustment is appropriate, and if the circuit capacity is exceeded, it is necessary to replace the more suitable power supply line and switch.

3.Air conditioning failure:If there is no problem with both air conditioners, but it is still causing tripping, then there may be a fault with the air conditioner itself, such as a problem with a short circuit or overheating of the motor.

At this time, it is necessary to ask professional technicians for overhaul and maintenance.

In order to avoid the tripping of two air conditioners at home,Needs attentionHere are a few points:

1.Check whether the load capacity of the home circuit is sufficient, and if it is insufficient, the circuit capacity needs to be upgraded in time.

2.When installing an air conditioner, it is necessary to reasonably consider the power and circuit capacity of the air conditioner to avoid overload.

3.Regularly maintain and clean the air conditioner, repair faults and replace old equipment in a timely manner.

4.When using multiple household appliances, it is necessary to reasonably distribute the electrical load to avoid tripping caused by using too many high-power electrical appliances at the same time.

If the home trips when two air conditioners are turned on at the same time, it could be due to one of several reasons:

1.Overload:

Two air conditioners running at the same time consume a large amount of electricity. If your circuit is undersized and guessed to carry such a large load, it can cause the circuit to be overloaded, triggering fuse or circuit breaker trip protection.

Solution: Make sure your circuit capacity can support running two air conditioners at the same time. If you need to increase the circuit capacity, consult a professional electrician for installation and adjustment.

2.Short Circuit:

When the air conditioner is running, if a short circuit occurs in the circuit, it can also cause the circuit breaker to trip.

Solution: Potato shed oak: Check the air conditioner power cord and plug for signs of damage or short circuit. If any problems are found, they should be replaced or repaired immediately.

There are two possibilities for a joke:

1. The air conditioner has a short circuit problem, which leads to direct tripping when powered on.

2. The current of the dust bridge has exceeded the carrying range of the line, and the miniature circuit breaker starts the protection program by itself.

1. What happens when the air conditioner trips as soon as it is turned on.

1. It may be caused by the instability of the voltage at home or the short circuit of the line, and the air conditioning compressor cannot start normally.

2. It may also be caused by an abnormality in the leakage protector at home.

3. The four-way valve of the air conditioner has a blow-by, which makes the high and low voltage of the air conditioner have problems, and when the current rises sharply, the air conditioner will trip as soon as it is turned on.

4. It is also possible that too much dust has accumulated on the condenser fins inside the air conditioner, which makes the air conditioner trip due to high heat load.

Second, how to solve the problem of tripping as soon as the air conditioner is turned on.

1. You can use the wiring board to reinstall a socket for the air conditioner first, and then try to start it. If there is still tripping, it means that the air conditioner is faulty. You can also unplug the power plug of the air conditioner first, and then send the gate up, if you can send it up, it means that the air conditioner has a fault, then you need to check in detail whether the air conditioning line has a short circuit, if it can't be sent, it means that the home line is abnormal.

2. If the insulation skin of the air conditioning line is damaged, then the insulation performance of the wire will deteriorate, and when the air conditioner is turned on, there will inevitably be a tripping phenomenon, which is an automatic power-off protection measure automatically initiated by the leakage protector at home in order to protect the electrical appliances, in order to prevent the air conditioner from burning out due to excessive current. At this time, it is necessary to use a multimeter to detect the socket, and if the wire is broken and short-circuited, it is necessary to ask an electrician to help detect and replace it.

3. If the socket of the air conditioner does not have a grounding wire or the wiring position is loose, it will also cause the air conditioner to trip as soon as it is turned on. If there is no abnormality in the socket, you need to check the compressor of the air conditioner in detail to see if there is any poor contact, and if so, you need to ask a professional to help repair it.

It means that one of the air conditioners or the air conditioning line is leaking, short circuit, or circuit load, which cannot support the operation of the two air conditioners. Solution: Check the wiring and whether the liquid rot line protection is turned on inside the air conditioner, find out the problem, and then repair it.

Solution: 1. You can take a look at the power of the two air conditioners, and then look at the voltage, if it is overloaded, the power consumption is too large, then the switch will turn on the protection device, that is, it will automatically trip, if it is really the cause of this failure, then the two air conditioners can not be used together under this Li answer power supply, you can change to a smaller power air conditioner, so that the load is within its range.

2. When there is a line problem inside the air conditioner, the protection mechanism will also be triggered, which will lead to tripping, at this time the fault detection, we can turn on an air conditioner, an air conditioner, and then see which air conditioner will cause tripping when it starts, then the fault is in the air conditioner, the air conditioner which buried the line to overhaul and verify, targeted maintenance can be eliminated, if the two air conditioners will trip no matter which one is opened, then it may also be a load problem, It is also possible that the lines of the two air conditioners are faulty, because the implicated lines can directly ask a professional air conditioner master to come to the door for maintenance.