W10Why can t I connect to the network?

First of all, understand that we have our broadband and password, and set it up.

The details are as follows:

To connect to broadband, you must first understand that we have our broadband and password.

We right-click on the network icon in the lower right corner of our desktop and we select "Open Network and Sharing Center".

In the Network and Sharing Center, we directly select the <> "Set up a new connection or network".

We select "Connect to the Internet" directly

My computer is currently connected to Wi-Fi, so I select the "Set up a new connection" <>

We directly select "broadband" to connect.

Next, we enter the username and password provided to us by the operator. After entering, we directly click on "Connect".

With the above settings we can connect to our broadband. We can use Kuandi to surf the Internet.

This step-by-step setup feels similar to the setup of Win7. We just need to get used to win7In fact, we use win10 is quite handy.

Hope it helps.

Win10 suddenly can't get on the network, maybe the system network configuration is not a problem, you need to reset the network configuration.

Fix the network configuration and winsock protocol.

Enter a command. netsh winsock reset enter, as shown in the following image:

Reset the IP settings to automatically obtain the IP and DNS server address by default.

Enter the command netsh int ip reset c: enter, as shown in the figure below

Restart your computer and see if you can surf the Internet.

What should I do if the W10 system network connection can't be usedHello dear, <>

First, confirm whether your wired connection is networked, that is, directly use the network cable to connect the router or the cat to see if you can access the Internet; If you can access the Internet in this way, the reason for the network failure is ruled out, and then we will see if the wireless network is completely linked, because it takes a while to connect to the wireless, if you enter the router in **1:1....If this step can also be detected, then it is time to go back to the problem of finding the network, first restart the route leaker to avoid the network cannot be connected due to the soft problem of the router; Then if you still can't access the Internet, then check whether your wireless network has changed its name, generally the network with a Chinese name may have a poor network connection; Of course, if none of the above is the problem, then call the operation manager to confirm whether your network is in arrears, because most of the networks are now bound to mobile phones, and the network will stop by itself if you are in arrears; Hope it helps.

If my answer is helpful to you, please give a thumbs up (in the lower left corner), I look forward to your like, your efforts are very important to me, and your support is also the motivation for my progress. Finally, I wish you good health and a good mood!

When the win10 network connection is restricted or a yellow exclamation point appears, right-click the "Network Connections" icon in the taskbar and select "Network and Sharing Center" from its right-click menu.

After entering the "Network and Sharing Center" interface, click the "Change Adapter Settings" button in the upper left corner of the window, and the "Network Connection" window will open, right-click the "Network Restricted" connection, and select "Disable" from its right-click menu.

Once the corresponding network connection icon is disabled, right-click on the network connection again and select "Enable" from its right-click menu.

In this case, for "Local Connection", the IP address is automatically obtained from the gateway and the connection is made. For "Wireless Network", you need to click the "Network Connection" icon in the lower right corner of the taskbar, and click the "Connect" button from the open extension panel, and you will find that the network connection is normal.

Of course, there are many reasons for the "limited network connection" or "no access to the network" issue.

When such problems occur, we need to check whether the router can connect to the Internet normally, and make sure that the "network connection is normal" in the router web management interface. Otherwise, you need to check the settings on the router side.

In addition, we can also use the "360lsp repair tool" to fix network failures. Use this tool to fix the LSP protocol and solve the problem of not being able to access the Internet normally.

At the same time, with the help of the "360DNS optimization" tool, the optimal network DNS filtering function can be realized, so as to solve the problem of "network instability" or "unable to open web pages".

Of course, if you upgrade to win10 official version of the system before you can not access the Internet normally, "limited network connection" or "no permission to access the network", it is recommended to use "driver life 6" to update or fix the network card driver.

Right-click the "Windows" button in the lower left corner of the desktop, and select "Computer Management" from its right-click menu.

From the "Computer Management" window that opens, then "Services and Applications" - "Services", find "Wired AutoConfig" and "WLAN AutoConfig", make sure they are in normal operation, otherwise click the "Start This Service" button in the upper left corner to turn on this service.

Consider whether the NIC driver is faulty.