3dmax2013 is stuck when the interface is opened

This is mainly due to the fact that the graphics card driver is too old.

Solution: Follow the new graphics card driver. Then open Max and go to Custom - Preferences - Viewport and change the Software Display Driver to D3D or other mode

Introduction to 3D Studio Max: 3D Studio Max, often referred to simply as 3DS Max or MAX, is a 3D animation rendering and production software based on PC system developed by Discreet (later merged by Autodesk). Its predecessor was the 3D Studio series of software based on the DOS operating system.

Before the advent of Windows NT, industrial-grade CG production was monopolized by SGI graphics workstations. The advent of the 3D Studio Max + Windows NT combination has suddenly lowered the threshold for CG production, first starting to use it in the animation production of computer games, and then further participating in the production of special effects for film and television films, such as X-Men II, The Last Samurai, etc. After Discreet 3ds Max 7, the official name was changed to Autodesk 3ds Max and the latest version is 3ds Max 2016.

Hello. I've come across this question many times.

This problem is mainly caused by the old graphics card driver, and has nothing to do with the computer configuration. Even if you open Max with a single-core + integrated display computer, this will not happen.

orDrive life and other driver management software with the latest graphics card driver to the latest version

Generally speaking, it can be solved after the new graphics card driver.

Then open Max and go to Custom - Preferences - Viewport and change the Software Display Driver to D3D or other modes. (I'm using the nitrous mode recommended by the software here).

You try it first, I hope it works for you.

The computer configuration is low, look at your version of 3D memory, graphics card requirements.

As soon as 3DMAX is opened, it is stuck in the main interface is caused by the wrong setting, and the solution is:

1. First, right-click "3D Max" and select "Properties".

2. Then enter the target column, add "-h" after the address, and click "OK".

3. Finally, right-click the software and run it as an administrator. Noisy <>

4. The summary is as follows.

The computer boot has been stuck in the motherboard logo interface, indicating that the problem was found in the power-on self-test process, and it needs to be checked one by one, and the problem can be solved before it can enter the sail system normally.

If the motherboard logo is displayed at boot and you can't enter the system, you need to restart and press the tab key to skip the logo screen or press the del key continuously when booting up (F2 or other specified hotkeys for notebooks.

Go to the CMOS settings page, turn off Full Screen Logo Show in the Advanced BIOS Features tab, and see if the POST information can be displayed, and then determine the problem.

In general, it can be based on a black screen.

Press the F1 key to skip the non-fatal error and start the computer directly, or press the del key to enter the CMOS, then press F9 to load the predefined or select Load Optimized Defaults or Load Fail-Safe Defaults, and then press F10 to save and exit the reboot.

If the original CMOS parameters are not saved or the system time in the CMOS is restored to the factory time after the shutdown and power failure, it may be the motherboard battery.

After the battery needs to be replaced, the predefined parameters are loaded and saved according to step 2.

If the above operations do not work, it means that there is a problem with the hardware, usually the memory is not in contact due to oxidation, or the hard disk may be in poor contact due to wiring or the hard disk master boot record.

Damaged, you need to reinsert the memory or hard disk, or repair the hard disk master boot record, or reinstall the system.

Or replace the hard drive.

The specific steps are as follows:

1. First open 3DMax and enter the page.

2. Then click on the "Viewport" in the pop-up window to open the preferences.

3. Then click to open "Select Driver" in the pop-up window

4. Then click and select "directx" in the pop-up window, press enter to confirm.

5. Then open the graphics driver settings, select "opengl", and press enter to confirm.

3DMAX is stuck in the main interface as soon as it is opened, which is caused by the wrong setting, and the solution is:

1. First, right-click on "3D Max" and select "Properties".

2. Then enter the target column, add "-h" after the address, and click "OK".

3. Finally, right-click the software and run it as an administrator.

4. The summary is as follows.

Stuck? Is it real death or fake death, if it's fake death, the menu can still be used, right? If it works, try setting the display driver under Customization, Preferences, and Viewports.

The reasons for the lag of the 3DMax model are roughly as follows:

1. The computer configuration is too low, and its performance is difficult to run 3dmax, so it is recommended to upgrade the configuration of the computer;

2, the Chinese version of 3dmax has many bugs, it is recommended to use the English version to open;

3. If you have a problem with the graphics card driver, please update the latest graphics card driver;

4. Set up the problem. Please change it in the settings of 3dmax. Just set it in the "Customize" section at the top.

1.Wait a minute!

2.If that doesn't work for a long time, you should always clean up junk files on your machine.

3.Your machine's accessories can be boosted a bit.

Exit Max and delete the dlcomponents in the 3dmax installation directory

dlcomponentlist file.

and then restart max and you're good to go.

Restart it, if it doesn't work, vray Chinese-English switcher, switch the VR Chinese-English point to start and solve it.

Or you can uninstall and reinstall.

1.Select the 3D Max software shortcut icon on the computer, click Properties, open the property box, add -H to the opening label, and click OK.

2.Start --Programs -->autodesk --change graphics mode opens.

3.After opening, the 3D Max software will pop up Display Driver Selection on the initialization screen, select [Legacy OpenGL].

4.This will open the software.

5.The next time you open it again, you will be prompted with the Display Driver Selection dialog box, because you selected [Legacy OpenGL] last time, so you can just click OK.

Check to see if your graphics card meets the boot conditions.

When installing 3dmax2015, it is stuck for the following reasons:

Open the software, find the 3dmax2015 item, select it and click the Remove button below.

There will be a pop-up window, wait for the pop-up window to complete and the registry to be cleaned up.

Then install the software.

The computer configuration is too low, and the loading is too slow, because 3DMAX2015 has relatively high requirements for computer configuration, and the machine is difficult to bring up, so it is stuck.

After exiting, uninstall 3dmax, and the registration list should also be uninstalled (uninstall with 360), and then reinstall, if the same problem still occurs, then there is a problem with your 3dmax source file!

The phone is stuck and can't run may be caused by the phone memory is too small, the phone memory occupies too much, there is no space left, resulting in the running stuck, it is recommended to clean up the phone garbage, and then restart the phone.

Here's how:

1. Use the mobile phone's junk cleaner software to clean up the mobile phone garbage, and then restart the mobile phone to check the running speed of the mobile phone.

2. If the mobile phone is still running after cleaning the garbage of the mobile phone, it may be that the system of the mobile phone is faulty, and you need to go to the after-sales service office of the mobile phone for professional repair.

In the start program, there is a change graphics mode in the autodesk file to open, 3 options appear to select the third opngl mode, the computer defaults to the first one, if it doesn't work, change to the second one, the graphics card is different, and the mode selected is also different

To install to open startup max