Windows 2003 Server cracks login passwords

Remove the hard drive and attach it to another computer to read it.

turned. XP,I've tried.,Just replace the sam file.,It works! I think it will work in 2003!

The dos command is as follows:

copy c:\windowsepair\sam c:\windows\system32\config\

When asked if you want to replace, enter y

I don't know if you use the administrator user? If not, when you boot up, you will be prompted to enter the password, you press CTRL+ALT+del to bring up a login box to enter the user and password, at this time you enter administrator, the password is empty. You can log in, and delete the original user's password to log in.

Addendum: I took more than an hour to install Windows 2003 and test it with my method, which did not cause a system crash.

If there is a SAM file under C: WindowsEpair, you can directly replace the SAM in C: Windows System32 Config to restore the administrator's user password to be empty.

Please forgive me if it was my method that caused your system to crash!

Go to the BIOS settings, there is the posscard setting inside, which is the password setting. If you can't get in, take off the battery of the BIOS, put it back on in a minute or two, and the original password will disappear.

Try not to move sam because the last time I moved sam on xp, the system crashed directly.

The 1st floor is so dedicated... However, I still recommend that you take off the hard drive and make a backup first.

It is recommended to start with PE to enter the modification.

Windows Server 2003 many friends in the process of use, need to change the login password of the user account, but do not know how to change it for a while, the following 3 ways to change the login password of the Windows Server 2003 user account.

Method steps.

1. This is the simplest, generally the most commonly used, directly press CTRL+ALT+del at the same time to return to the standby interface to have the option to change the password. Click "Change Password", then enter the old password, then enter the new password, and you're OK. It is important to note that if the initial password is empty, you may not be able to change the password.

The reason is because some students install some ghost versions of the system, and in this version, this method is not applicable to the initial password is empty. But that's okay, there are 2 more ways to do it below, keep reading.

2. Right-click on "My Computer", select "Manage", if you don't have it on your desktop, then look for it from the "Start" menu.

Then in the pop-up dialog box, select "Users" under "Local Users and Groups", left-click "Users", right-click on the administrator that pops up on the right, select "Set Password", read its prompt message, click "Continue", then enter your new password, and click OK.

It is worth noting that under some ghost versions, the option of "Local Users and Groups" cannot be found, so you cannot change the password. The reason is because some students have installed some ghost versions of the system, and in this version, this method is not applicable. But that's okay, there's a third way, keep reading.

Click the "Start" menu, select "Run", enter "cmd", OK, in the pop-up DOS command dialog box, enter net user administrator, and then come back, you will see the prompt.

Description: Here net user is a command to add or change a user account or display user account information.

administrator is your login username (if you have changed it, write your current username, you can refer to method 2 above to find your current username).

This is the password you want to change into, you can see that the password I entered for the first time is too simple, the system defaults to uppercase + lowercase + number, but different versions of the system, there may be slight differences, you can try.

If you want to modify it to empty, the command should be net user administrator""(Two half-width quotation marks next to each other,That is, the quotation marks in the state of the English input method)

If it happens that your initial system password is empty, the first method cannot be used, and you are using a pure version of the Chinese Simplified Chinese Enterprise Edition system, there is no "local users and groups" in the second method, then this third method can help you solve the problem.