-
Anonymous users2024-02-071: The electromagnetic interference problem can now be ruled out according to your explanation! The anti-interference ability of the signal line is not very prominent. You can ignore it for now.
2: It has nothing to do with the motherboard and the power supply. According to your description, it has nothing to do with the monitor.
3: Changing the driver version is not a very prominent factor, so it will not be considered for the time being.
4: You are still in a relatively slight state of disadvantage, which will gradually deteriorate. I point out responsibly:
A: The capacitance or MOS tube on the graphics card is defective. b：
GPU virtual soldering or defective. C: Video memory memory particle BGA virtual soldering (if it is A, it can be repaired.)
If it's B, it's not cost-effective. ）
- Follow me: Let's consider C: -- Memory memory particles BGA virtual soldering --- remove the heatsink on the graphics card, remove dirt, and apply a paper-thin layer of silicone grease.
Then, you look at the block memory particles on the graphics card, how many memory particles are there? First, stack 12 layers of 80 grams of paper, cut them to the size of two-fifths of the memory particles, and install the radiator to hold the particles. The aim is to compress and improve virtual welding.
Very effective. Tell which one it is? Generally, start with the one close to the slot.
It's the method of elimination, anyway. Eighty percent of it was the one closest to the slot. Be sure to pay attention to the size of the force, don't crush it!
I hear good news from you!
-
Anonymous users2024-02-06It's not a power issue, take a look at your refresh rate.
Desktop right-click Properties to set the monitor screen refresh rate.
Above 60 hertz, if you wear glasses, it will be higher about 80.
-
Anonymous users2024-02-05It is a very common phenomenon for the display to appear water ripples, and it is sometimes called "jitter" by people, and many people will feel that this phenomenon will affect their own experience. So, what is the cause of water ripples in the display?
1.Signal Transmission Problems: In the era of computers, most monitors used wires to transmit signals from the computer to the display. If the connection is poor or damaged, the instability of the signal transmission will cause water ripples on the display.
2.Monitor's refresh rate: A monitor's refresh rate refers to the number of refreshes per second, usually measured in Hz. If the refresh rate of the display is too low, it may cause water ripples in the display.
3.Display driver issues: For example, if the driver is infected by a virus or the driver is outdated, it can cause water ripples on the display.
4.Display coil problem: The coil in the display is a device used to transmit and receive signals, and if the coil is damaged or deteriorated, it is easy to cause water ripples in the display.
5.Power supply problems: During the use of the monitor, if there is a problem with the power supply, it will cause the display to ripple water.
The above are the causes of water ripples on the display. If you encounter this situation, you can first troubleshoot the above problems and find a suitable solution. At the same time, using a high-quality monitor can also avoid this problem.
Use a soft cloth dipped in a little water but do not have water droplets, you can gently wipe the LCD, or wipe it with lens paper and detergent, and never wipe it with a corrosive cleaning solution. The flickering of the LCD screen is related to the voltage or the surrounding electrical appliances, and there are two possibilities: one is poor contact, and the other may be a problem with the high-voltage board. >>>More
Screen shocks or pinching: If your phone has ever been impacted or pinched, it can cause damage to the circuit board inside the screen, resulting in color spots. 2. >>>More
The new Bora this car is 7500 kilometers to do the first warranty, the start of the instrument on the maintenance of the sign, this is to prompt you car has reached the number of kilometers to do maintenance, so you should take the time to go to the 4S shop to your car maintenance, the first warranty is very simple, the main thing is to change the oil, oil filter and air filter, the time required is relatively short, at most half an hour can be done, and the first warranty of the new car is generally free. If you don't go to maintenance, of course, the car itself is focused on maintenance, regular maintenance can greatly reduce the failure rate of the car, on the contrary, if you do not maintain or maintain irregularity, this will lead to a great increase in the failure rate of the vehicle, so timely maintenance on your own car can be said to play a good role in protection, so that the vehicle remains in a very good state, when you go to the 4S shop or service station after maintenance, the maintenance staff will use the computer to clear the maintenance signs displayed on the car instrument. The next maintenance time is 15,000 km, which means that the maintenance sign on the instrument will be lit up when it is almost 15,000 km. >>>More
If the pressure is too heavy due to the use time for too long, and something magnetic is nearby, turn off the monitor and then turn it on to see if it can be normal.
1. When the computer is first turned on, the screen of the monitor shakes very much, and sometimes even the icons and text cannot be seen clearly, but it will return to normal after a minute or two. >>>More