How to use the Tenda W541U as a wireless router

Depends on the brand of wireless router you bought. The advanced routing is connected to the host with the network cable café route (remember that the host cannot help but connect the wrong interface when it is connected to the route, and should be connected to the interface represented by the number of the route), and then enter the routing setting after it is connected. When entering the route, different routes are different from the default gateway (d-link, the default is to enter **, and then he will call you to enter and password (d link::

admin,Password:admin or "blank" (blank is no password),After entering, it seems that the first item is a quick setting (look at the first item) Select popp3 and then go down should be able to set it up and then click on the wireless management to open the wireless network function,Add a password Finally, connect the Moden to the Internet (it seems to be called) port of the route, it should be able to pull。 If you don't understand, read the manual carefully, and if you don't understand, I'll pull the wireless network card, install the driver, and you don't need to set it up.

It can be set to AP mode to transmit WiFi signals for wireless devices.

The network card can only be used as an AP, set up a soft AP, and send a wireless signal!

The cat is connected to the ** wire wireless router and cap connection.

No matter what model or brand of "wireless router" the right side of the router has the management address, username and password of the router background.

Don't change anything after entering the background (if you have changed, please look for it in the manual, restore the router factory settings, and restore the factory plant).

In the background, select the Setup Wizard Next If it's broadband, select ADSL Virtual.

In this way, if you open the wireless device of this book and search for the wireless network, it should be able to pull well.

I didn't make it clear, whether the wireless connection can not go to the Internet, or the wireless can not be connected at all, the wired can afford, the wireless connection does not mean that there is a problem with the settings of the routing wireless, see if the DHCP service of the route is turned on, as well as the range of the IP address pool, and whether there is a MAC binding, etc.

1. The broadband network cable or the network cable out of the cat is connected to the WAN port of the router, and the LAN port is connected to the computer.

2. Enter in the address bar to enter the wireless router settings interface. (If you can't get in, please look at the nameplate at the bottom of the router or the router instruction manual, the default settings of different models of routers are different.) ）

3. An account and password to log in to the router appear in the settings interface, enter the default account and password admin, or refer to the manual;

4. After successful login, select the interface of the setup wizard, which will automatically pop up by default;

5. After selecting the setup wizard, a window will pop up to explain that you can set the basic parameters of the router through the wizard, and click Next directly;

6. Set up step by step according to the setup wizard, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

7. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

8. Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

9. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

Oops, DHCP is a problem with router settings. Look for it Tengda is domestic, Chinese interface, just a few more clicks.

Just turn on your router's DHCP server.

1. Line connection:

a.Connect the network cable from the cat to the router (WAN port), and then connect the network cable connected to the computer to the router (any port numbered 1, 2, 3, 4).

b.Connect the broadband cable to the router (WAN port), and then connect the network cable connected to the computer to the router (any port numbered 1 2 3 4).

2. Log in to the router interface.

In the browser, type: Enter, enter in the pop-up page: admin and click "OK".

3. Set up the router to surf the Internet.

Click Quick Settings - select the corresponding Internet access method to set up.

The corresponding connection mode for ADSL dial-up is: PPPoE

To cats. The network cable out of the cat is connected to the WAN port of Tengda route, and then from one of routes 1-4 to the computer.

Here's how to set up your router:

1. Line connection:

a.Connect the network cable from the cat to the router (WAN port), and then connect the network cable connected to the computer to the router (any port numbered 1, 2, 3, 4).

b.Connect the broadband cable to the router (WAN port), and then connect the network cable connected to the computer to the router (any port numbered 1, 2, 3, 4).

2. Log in to the router interface.

In the browser, type: Enter, enter in the pop-up page: admin and click "OK".

3. Set up the router to surf the Internet.

Before setting up the Internet, choose the correct way to access the Internet: it is generally divided into 3 types, as shown in the following blind slag:

ADSL dial-up: Usually Internet access (do not connect the router when the group god code) needs to click on the broadband connection, dial-up is successful before you can access the Internet, you should choose the Internet mode, Internet access and Internet password correctly enter the broadband and password, you can.

Automatically obtain an IP address: If you usually surf the Internet (when you are not connected to the router), you only need to set the local connection of the computer to automatically obtain the IP address to access the Internet, you should choose this Internet access method.

Static IP: If you need to fill in a fixed IP address in the local connection to access the Internet (when you are not connected to the router), you should choose the Internet access method, log in to the interface of the router, click "Advanced Settings" - "WAN Port Settings" to select the static IP mode "Static IP Mode", and enter your fixed IP address, subnet mask, gateway, DNS domain name server and other parameters correctly.

4. After setting, click "Advanced Settings" - "System Status" to check whether the connection status of the WAN port shows that it is connected, and whether the corresponding connection mode is displayed correctly.

The corresponding connection mode for ADSL dial-up is: PPPoE

The connection mode corresponding to the static IP address is the static IP address

**The following is how to set it up

The steps of the Tengda W548D wireless Zen Router setup method are as follows:

1. First connect the power supply, then plug in the network cable, plug the incoming cable into the WAN port, and then plug in a LAN port with the network cable connected to the computer.

3. After connecting, you will see that you will enter the corresponding login user name: admin and password: admin.

4. Enter the operation interface and click the Setup Wizard.

5. Enter the interface of the setup wizard and select the Internet access mode setting.

6. Click Next to enter the Internet access mode settings, and you can see that there are three ways to access the Internet. If it's dialing, then use PPPoE. Dynamic IP can be used by plugging the computer directly into the network, and there is a DHCP server on the upper layer.

The static IP is generally a private line or something, or it may be a cell bandwidth, etc., and the upper layer does not have a DHCP server, or wants to fix the IP.

7. If you choose PPPoE dial-up Internet access, you need to fill in the Internet account and password.

8. Then click the next step to enter the wireless settings, you can see the channel, mode, security selection friend, SSID, etc., generally SSID is a name, you can fill in at will, and then the mode mostly uses 11BGNFor wireless security options, choose WPA-PSK WPA2-PSK, which is so safe, so as not to make people crack and rub the network with a light cover. Click Next to set it up successfully.

9. Click Done, the router will automatically restart, and the router setup will be completed.

Here's a tutorial for the W541R router, see for yourself.