METTLER TOLEDO scales cannot be zeroed

After the items are placed on the ground scale, the zero key cannot be used, and the error displayed by the meter ** means that the zero range is out of the range and the zero has failed. The correct way is to press the tare key, and the meter will show a net weight of zero.

Precautions for using weighbridges.

1. The total weight of the weighed vehicle or cargo is not allowed to exceed the maximum weighing capacity of the scale of 100 tons under any circumstances. It is forbidden to overbalance a short-wheelbase vehicle, such as a forklift approaching the maximum weighing.

2. When the vehicle is weighed, the vehicle should go straight to the middle of the weighing platform at a speed of less than 5km h, and then brake lightly and measure after stationary. In case of data fluctuations due to wind, the data should be weighed only after the data is stable.

3. It is forbidden for the vehicle to make emergency brakes or park for a long time on the weighbridge platform.

4. It is strictly forbidden to do any work on the weighbridge platform.

5. Before the vehicle is weighed, the soil, ice and snow should be removed, and it should be confirmed that there are no personnel and other sundries on the weigh.

6. In use, the spilled items on the weighing platform should be removed in time, and the empty scale should be confirmed in time after cleaning (that is, the weighing display controller is reset to zero).

7. There shall be no foreign objects such as stones and coal blocks stuck in the gap around the weighing platform.

8. Regularly check whether the limit clearance is reasonable (the gap between the head of the transverse limit bolt and the side of the sensor is kept at about 3mm, and the gap between the head of the longitudinal limit bolt and the side of the embedded parts is kept at about 3mm), and the limiter and the scale body should not collide and contact (the gap is 2-3mm).

METTLER TOLEDO took the lead in using orthotropic theory to design the world's most advanced platform structure - U-shaped steel assembly welding structure, the key welds are fully automatic and continuous welding, and the new products of various specifications must pass the full load and high-frequency fatigue test of the whole scale in the development process. METTLER TOLEDO platform has high overall strength, rigidity, torsional and lateral force resistance, and corrosion resistance to ensure long-term stable and reliable use.

There are several possibilities that the weighbridge cannot be cleared:

1.The weighbridge is damaged, the internal sensor of the electronic scale is damaged, the sensor signal line is damaged, the body sensor is damaged, the sensor signal line is damaged, the installation position of the body sensor is incorrect or the sensor signal line is broken or the connector is in poor contact.

2.The internal junction box of the weighbridge is damaged, the sensor signal line is damaged, the body sensor is damaged, the sensor signal line is damaged, the installation position of the body sensor is incorrect or the sensor signal line is broken or the connector is in poor contact.

3.The internal junction box of the weighbridge is damaged, the sensor signal line is damaged, the body sensor is damaged, the sensor signal line is damaged, the installation position of the body sensor is incorrect or the sensor signal line is broken or the connector is in poor contact.

4.The internal junction box of the weighbridge is damaged, the sensor signal line is damaged, the body sensor is damaged, the sensor signal line is damaged, the installation position of the body sensor is incorrect or the sensor signal line is broken or the connector is in poor contact.

Hello, dear users, after placing the items on the ground, you can't use the clear button, and the error displayed by the meter ** means that it is out of the range of clearing, and the clearing fails. The correct way is to press the tare key, and the meter will show a net weight of zero.

If you still have questions, please feel free to ask the company.

Summary. The adjustment method of METTLER TOLEDO electronic bang is as follows:1

First of all, check whether the power supply of the electronic bang has been connected, and make sure that the power supply voltage meets the requirements. 2.Check the controller of the electronic bang to make sure that the controller is set up correctly and that the input and output signals of the controller are normal.

3.Adjust the vibration frequency of the electronic bang to ensure that the vibration frequency meets the requirements. 4.

Adjust the vibration amplitude of the electronic bang to ensure that the vibration amplitude meets the requirements. 5.Adjust the vibration time of the electronic bang to ensure that the vibration time meets the requirements.

6.Check the safety device of the electronic bang to ensure that the safety device is working properly. 7.

Check the control system of the electronic bang to make sure that the control system is working properly. 8.Check the vibration pattern of the electronic bang to ensure that the vibration pattern meets the requirements.

9.Check the vibration accuracy of the electronic bang to ensure that the vibration accuracy meets the requirements. 10.

Check the vibration stability of the electronic bang to ensure that the vibration stability meets the requirements. The above is the adjustment method of METTLER TOLEDO electronic bang, I hope it can help you.

The adjustment method of METTLER TOLEDO electronic bang is as follows:1First of all, check whether the power supply of the electronic bang has been connected with the wide circle, and make sure that the power supply voltage meets the requirements.

2.Check the controller of the electronic bang to make sure that the controller is set up correctly and that the input and output signals of the controller are normal. 3.

Adjust the vibration frequency of the electronic bang to ensure that the vibration frequency meets the requirements. 4.Adjust the vibration amplitude of the electronic bang to ensure that the vibration amplitude meets the requirements.

5.Adjust the vibration time of the electronic bang to ensure that the vibration time meets the requirements. 6.

Check the safety device of Qiaoyou Electronic Bang to ensure that the safety device is working properly. 7.Check the control system of the electronic bang to make sure that the control system is working properly.

8.Check the vibration pattern of the electronic bang to ensure that the vibration pattern meets the requirements. 9.

Check the vibration accuracy of the electronic bang to ensure that the vibration accuracy meets the requirements. 10.Check the vibration stability of the electronic bang to ensure that the vibration stability meets the requirements.

The above is the adjustment method of METTLER TOLEDO electronic bang, I hope it can help you.

I'm still a little confused, can you be more detailed?

1.Cause: METTLER TOLEDO e-Bang regulation problems can be caused by a faulty circuit board of the e-Bang or an unstable supply voltage of the E-Bang.

2.Solution: (1) Check the circuit board of the electronic bang, if there are damaged parts, you can try to replace the new parts; (2) Check the power supply voltage of the electronic bang, if the voltage is found to be unstable, you can try to replace the new power supply; (3) If the above two methods fail to solve the problem, you can try to send the electronic bang to a professional repair shop for repair.

3.Personal tips: (1) When using electronic banging, you should pay attention to check whether the electroosmosis car voltage of the power supply is stable, so as to avoid the problem of adjusting the envy; (2) If it is found that there is a problem with the adjustment of the electronic bang, it should be inspected and repaired in time to avoid greater losses.

Hello, dear, glad to answer for you: METTLER TOLEDO scale adjustment steps are as follows:1

Clean the weighing area and make sure there are no foreign objects. 2.Place the tray on the scale and make sure the tray is placed smoothly.

3.Turn on the scale and wait for the system to start. 4.

According to the scale's instructions, select the weight you want to calibrate or use the calibration assignment value. 5.Select the correction method:

Generally, electronic scales provide two ways - manual and automatic, and it is usually recommended to use automatic calibration. 6.Calibration is performed according to the instructions on the weighing pan, which usually requires placing a correction weight or dispensing a value on the weighing pan.

7.Perform a calibration and wait for the system to stabilize. 8.

Once the calibration is complete, you can perform a test to confirm the accuracy of the scale's shack limbs. Pro, the adjustment steps of the electronic scale may vary depending on the model spike and silver and the manufacturer, so it is recommended that you carefully refer to the instruction manual of the electronic scale for calibration.

Hello, the adjustment method of METTLER TOLEDO electronic scale is as follows:1Place the scale on a smooth, level surface.

2.Press the "ON off" button to turn on the scale and wait a few seconds until "Qingfeng" appears on the display. 3.

Place the items on the scale on the weighing pan and make sure that the weight of the items does not exceed the maximum weight of the scale. 4.The scale is not reading accurately, you can press the "tare" button to reset the scale reading to zero.

5.You need to adjust the accuracy of the scale, you can press the "mode" button to select the desired accuracy mode. 6.

If you need to change the unit of the scale, you can press the "unit" button and select the unit you want. 7.Once the adjustment is complete, you can press the "ON off" button to turn off the scale.