What should I do if I get a new motherboard and no drive drive? 30

Hello. I'll give you a look :

The motherboard needs to be driven, which mainly depends on the chip on the motherboard, such as the sound card, the network card, the integrated graphics card, and the like. You can go to the motherboard manufacturer's official **go to**chip driver,You can also use software such as the driver wizard to automatically install the driver. You can also go directly to the official **Go to the official **Go to the manufacturer of the integrated graphics card of the sound card network card**, now most of the sound card network cards on the motherboard are produced by realtek, and the graphics card is nvideo and ati two manufacturers.

The system does not need to be reinstalled, as long as the chip driver is installed.

Personally, I don't like to reinstall the system, and it is very troublesome to install all kinds of software back. As long as you use it, you don't need to reinstall it.

It is strongly recommended that the seller give you the driver or tell you the model of the motherboard to facilitate you to go** If you try your luck with a saucer, if you are unlucky, there is no network card driver, then you will not be lucky, or contact the seller. Good luck to the landlord Don't do anything to drive the elf.,If there's no network card.,It's useless.,Can't access the Internet.。

After replacing the motherboard, install the system directly, after entering the system, the general network card driver thinks that there is no driver on the Internet, and the next driver wizard will automatically get it.

Install the version with ghost is generally a universal drive.

Look at the motherboard description and write the motherboard model, and you can use the hardware detection function of software such as Kingsoft Guardian to find out the motherboard model, and then go to the official **search for the motherboard name,**Hard disk drive document installation, the document name is usually ATA driver. The new system disk is generally integrated into the latest hardware drivers, such as 2013XP and 2013WIN7 systems. Some driver software can also upgrade the pre-judgment driver, but it may not be compatible.

Today's ghost system has integrated most of the commonly used drivers.

After completion, go to the device manager to take a look, if the driver is not installed, use the driver wizard to install it automatically.

Use the next driver wizard on the USB flash drive, and then install it on your computer, as long as the network card driver is installed, and then it will be updated.

Is it a new motherboard without a CD?,You've been fooled.,You can use it without a driver.。 For good performance, it is best to install the driver. Since you don't have a CD, go to your brand's official website to find it.

Haha The motherboard comes with its own driver, so don't worry about it

Be sure to use the motherboard drive disk to drive the motherboard, if you don't have an optical drive, you can ask a friend to help copy the disc drive to the U disk, and then install it on your computer.

The current ghost version of the system has integrated most of the hardware drivers, and there is generally no need to install the drivers after installing the system.

Open the U disk,Generally, click directly on the inside or you can pop up the installation interface,Generally, you can go to the Internet**A driver wizard,You can detect whether the driver is installed,And then install it directly from the Internet。

1.Turn on the computer, put the XP installation disc in the optical drive, then press and hold the del to enter the BIOS, and set the CD-ROM to the first boot! If prompted"boot from cd", press enter.

2.Enter the splash screen, select Install WinXP, press Enter to install! Pressing enter may appear"press any key to boot from cd"At this time, continue to press enter, otherwise the hard disk will start.

3.Select the 1st one, press enter, and start the installation, reading the driver to memory.

4.After loading the driver, you can see the partition of your hard disk, and it is recommended to install the C drive. It should be noted here that if you want to do a clean install, then you need to format it, so the key to formatting is to delete the C drive first.

Only the XP installed in this way is a brand new XP. So please move the cursor to the C drive and press"d", delete partition C.

5.You pressed"d"After (delete), XP will confirm that you will lose data because you are afraid that you will delete it by mistake and prompt deletion. Of course, I'm just going to format it and then install it, so please press it"Enter"Go on.

6.Keep pressing"l" 。

7.After deletion, the C drive becomes an unpartitioned partition! Press"Enter"Go on.

8.Here you will be asked to choose the disk format. Let me talk about the difference between NTFS and FTA.

First of all, NTFS has all the advantages of FAT, NTFS has less fragmentation than FAT, high security, can encrypt files, supports disk quota, supports partitions above 30G, supports compression, and compresses up to 50%. I like to use NTFS and declutter the disk very quickly. However, due to the high security of NTFS, the NTFS partition cannot be accessed under DOS, and it cannot be formatted for the boot floppy disk, only the XP disc can be formatted.

So, if you're not sure, it's better to use FAT. The following 4 choices, (fast) means quick format.

9.Press"Enter"Go on.

10.Formatting.

11.The installation begins. The disc installation is automatic, from start to finish, and it is estimated to take 20-30 minutes.

12.Familiar installation screens.

13.Installed, 1st reboot.

14.Installed.

If there is a system image file or system backup on the hard disk, then you can use the installed one-click ghost, run the manual operation, and find the source backup file and drop out of the name. GHO is restored to the system disk to install,Or the computer settings can be started from the U disk and the U disk boot tool is used to enter the PE and then the same is installed with the ghost tool!