How to use a router to divide the network to another computer

If one is turned on, the other will be disconnected, which may be the problem below:

Judging by the fault phenomenon, it is suspected that the router is faulty. We recommend that you take the following steps to troubleshoot:

Restart the router and see if the fault is resolved.

Check that the connection between the computer and the router is a pass-through line. Although some routers support automatic rollover, however, using the wrong jumper often leads to inexplicable malfunctions.

Use the "**server + adsl modem" replacement method to repeat the power on and off operation of the two computers to detect the adsl modem.

Whether the connection is normal. If an exception occurs, it indicates that the ADSL modem is faulty.

Replace the router and test if the problem is resolved.

It is also possible that there are the following reasons:

When using a broadband router for Internet connectivity, you must revert the ADSL modem to its default setting, i.e., disable its routing capabilities. Then, in the broadband router, set the parameters such as the AD SL connection mode, user, and password.

OK. Typically, a d sl

The modem all have a button to restore factory defaults, and simply press the button to restore their factory default configuration.

Very simple. The network cables of the two computers should be connected to the LAN interface of the router, and the network cable of the ADSL connection route should be connected to the WAN port of the router. Set the account name and password in the re-entry route. The IP address can be obtained automatically, or manually if not.

First of all, check whether the line is connected properly.

Then check whether the land game is set up correctly, and you need to set the account name and password for land game autodialing.

The router of the brand you bought has instructions inside, and you can operate it for a long time according to the instructions!

Calling the other party is also set to automatically obtain the IP address

If that doesn't work, enter it manually!

See if you bought a router? I still bought it as a hub, and then read the instructions carefully when setting up the route, and it should work step by step!!

The network cable separated from the wireless router is connected to another wireless router: set up a level 2 router.

1. Setting method:

Before setting: Please disconnect the 2WAN port network cable of this router and plug it in after the setting is complete.

1. Set the IP segment of the second router

2. How to set up a second router to access the Internet:

1. Check the IP details of the computer connected to the first router.

2. Set up on the second router: select static IP in the setup wizard: enter the IP that the first router does not use, and the others: mask, gateway, and DNS settings are the same.

3. Restart the router after setting it up.

3. Unable to enter the router method:

Computer into the router:

1. Check your IP first, method: win+r--- enter: cmd--- enter in the black and white interface: ipconfig, and press enter.

4. The router login interface pops up, and enter the default login username of the router: admin and password: admin.

You can set the first router to be able to surf the Internet, and then enter the background of the second router to make relevant settings. Then use a network cable to plug in the LAN port of the first router and connect the WAN port of the second router to access the Internet. The specific connection method is as follows:

1. Take the first router as a wired router as an example, and connect the LAN port of the first router to the computer.

2. Enter the IP address of the router in the browser address bar and press enter to enter the password to log in.

3. After logging in to the router background, click Interface Settings, and then click WAN Settings. Choose how you want to access the internet and enter the relevant information. If you choose to dial up the Internet, enter the Internet access and password and click Save.

4. Click LAN port settings, select DHCP service, check the enable DHCP function, and click Save.

5. At this time, insert the network cable into the WAN port of the router.

6. Click on the system status of the router to see that the first router has been set up and can access the Internet.

7. Disconnect the first router from the computer, and use the network cable to plug into the LAN port of the second router to connect with the computer.

8. Enter its IP address in the browser address bar, and enter the password to log in.

9. After entering the router background, click on the routing settings.

10. Click Internet settings on the page that appears, and click Save after selecting to automatically obtain IP address.

11. Click Wireless Settings, check Turn on Wireless and Broadcast, enter the wireless name and password and click Save.

12. Click LAN port settings, enter a different IP address from the first router and click Save.

13. Click on the DHCP server, check the box and click Save after enabling the DHCP function.

14. Insert the network cable separated from the LAN port of the first router into the WAN port of the wireless router to complete the setting and surf the Internet.

The router can be separated from another router, which is often used to expand the coverage of wireless wifi and realize the wireless wifi coverage of the whole house, so that the transmission signal attenuation problem can be avoided due to the long network cable, and the network can be extended.

How to set up the main router:

1. Plug the network cable (bus) into the WAN port of the wireless router, plug one end of the network cable into any LAN port of the wireless router and connect the computer network card at the other end, and turn on the power supply of the router.

3. Then enter admin, the default account name and password are the same (there is also a prompt for the original data on the back of the router) to confirm.

4. After entering the wireless router setting interface, select the Internet access method according to the setup wizard (different broadband options are also different), and enter the Internet access and password.

5. Save and continue to set the wireless key.

6. After saving, you can surf the Internet normally.

7. If it is abnormal, you may wish to click the reset button of the wireless router and set up the router again.

Hello landlord:

1.The router has a small button, press it until the router light goes out, and then release it to restore the factory value.

3.The IP address is conflicting, and since you have one or more routers in front of you, adding another router IP should be changed to a higher IP address.

Lenovo wireless router is broken, right? You don't need to connect the WAN port, and the LAN port light that connects the computer to the Lenovo wireless router with a network cable should be on. At this time, you can configure Lenovo wireless router to set the network segment to the network segment of different unit routers, such as:

The first router split out the network cable plugged into the wireless router WAN is right.

Directly plug the network cable out of the unit into the LAN port of your router, and your other computers are connected to the other 3 LAN ports (4 LAN ports in general), if it is a wireless direct search signal, it is OK

If the latter case is not available, it is generally that the address pool of your route is not in the same IP segment as the address pool of the unit route, so it is good to set it.

Wouldn't you just think of a wireless router as a switch?

Today's routers have AP mode, and they search according to the routing brand.

I've done this before.

Let's explain it step by step first, and if you have any questions, you can follow up.

Because of the IP address conflict, you need to change the LAN port address of the second router to the address of a different network segment. If the first router has not been specifically configured, its LAN port address (i.e., the login page address of the router) is generally the same as that, then you can change the LAN port IP address of the second router to another CIDR block address.

Don't connect the two routers at first (completely disconnect the two devices).

Then use a wireless or wired connection (you're a desktop, connect directly to the router with a network cable) and land on the management page of the second router (initially, but also with ).

In the basic settings, change the LAN port IP address to log in to this address to manage this router B).

Then save, restart the router to apply the settings.

Now you can connect the two routers for debugging.

To clarify, if your first router has been set to enable automatic dial-up to connect to the Internet, then the second router will generally be automatically detected without other settings. To ensure normal networking, set the WAN port connection type to Dynamic IP.

If not, you can log in to the second router, select your connection mode in Network Parameters > WAN Port Settings (dial-up Internet access is PPPoE), fill in the user account and password, and set up automatic dial-up connection.

Of course, you can also log in to the first router to set up an autodial-up connection.

To explain again, the above two routers are connected to the WAN port of the B router in the form of connecting the LAN port of the A router with a network cable.

In this way, the computer connected to the second router can enter the management page ( and ) of the two routers at will and at the same time to set up and manage the operation.

The above method can also be applied to the connection mode of broadband modem, fiber modem, and then router below.

The two routers are connected in this way, the gateway and the DHCP server are separate, they are in different network segments to avoid IP address conflicts, but the devices connected downstream of them cannot access each other. For example, if you turn on a homegroup on a computer that is not on the same network segment, you can't share content or devices.

It's easy. There are 2 types of connections!

1 is to use the router as a switch.

On the second router, fill in the IP address of the same network segment, DHCP is turned off, and all three network cables are connected to the LAN interface.

2 Directly restart the router into a network segment.

For example: the IP address of the first router is , then select the static IP address in the WAN settings on the second router (generally we fill in the account password), and fill in the IP address of the network segment of the first router (for example, then, the LAN address on the second router is arbitrarily set a network segment (, other settings are similar to the first one.

The network cable connected from the first floor must be connected to the WAN interface, and the other cables must be connected to the LAN interface.