How to network 10 of these computers

You need to add an exchanger with the least number of ports!

phone1->modem1->route1->> computer.

phone2->modem2->route2->> switch->> computer.

The WAN port of the second router is connected to the ordinary port of the first router!

That is, whether there is a network cable interface on the wall, a socket, a little larger than the ** line, if there is, it is easy to do to buy a 24-port switch How many computers go to the computer city to buy as many network cables as one connection

If there is no wiring in the wall, it will be more ugly, and when you go directly to the computer city to buy a network cable, buy a longer one, and every computer can be connected to the switch

The two routers cannot reach the same level of LAN.

You can only buy one switch. One way and again. The two can't get it together.

Hello everyone, I'm Daming, 60 computers The equipment required for the computer room is also the network cable, switch, router, this scale is even a small local area network, and then I will explain in detail how to network and <>

How to connect to a LAN with 60 computers

First of all, the first step should be to connect the "router" and the "optical modem" in series, the network cable required for series connection is not too long, one end is connected to the WAN port of the "optical modem", and the other end <>is connected to the LAN port of the "router".

Then log in to the background operation interface of the "router", find the "WAN port" option of the "Internet mode", the Internet mode is divided into three types, namely, "PPPoE broadband" to destroy "dynamic IP" and "static IP", usually the school of this scale of broadband is used "static IP", directly write the IP address into the WAN port of the router, <>

After setting up the router, when connecting the "router" and the "switch in series", you also use a network cable, one end is connected to the LAN port of the "router", and the other end is connected to any interface of the "switch" to complete the series

Note: If the interface of a switch is not enough, you can also connect a switch in series, and the two switches in series only need to be connected to any port with network cables, <>

Finally, after all the devices are set up and connected in series, you can connect 60 computers directly to the interface of the "switch" with network cables

Summary

This Q&A explains how to make a small-scale LAN with 60 computers, focusing on how to connect in series, which interface you must remember to connect to, and how to set up the router

The above is the content shared today, I hope it will be helpful to everyone, if you like it, don't forget to like and follow! Daming will continue to create works on "computer maintenance and application", if you have different views on such issues, you can discuss them together in the comment area, okay, let's see you next time!

Use tp-link, that's what I use, and add an 8-port hub.

One uses a router, spend about 100 yuan to buy a broadband router, such a thing is generally one wan and four lan, that is, you can directly connect 4 machines, if the machine has more than 4, you can also buy another switch, which is also very cheap. Connect your ** cable to the cat, connect the other end of the cat network cable to the WAN port of the router, and then make a few network cables to connect the network card of the machine to the LAN port of the router. Then, look at the manual of the router, mainly to know what the default connection address of the router is, generally.

http: You can open the control interface of the router, select the Internet mode, such as ADSL, that is, select PPPoE, and enter your ADSL account and password. ok！

Note that you should not install PPPoe dialing software in your machine, dialing is done automatically by the router, and do not establish other connections, only keep the local connection of the network card. Other machines have similar setups, such as:

IP address mask gateway DNS.

As long as the IP addresses are not duplicated.

If the connection address of the router is something else, such as:

Then the IP address of the machine is set to the gateway is, and the others are the same as before.

The second uses dual network cards, because there is always a machine to boot up, it is rarely used, and it is not in detail. Let's take the system as an XP (Internet server) as an example.

Aren't you multi-computer? One of them serves as an Internet server and installs two network cards. **The cable is connected to the cat, and the cat's network cable is connected to one of the network cards (the parameters do not need to be set, the default). The other NIC is connected to your switch (and the hub is the same) with the parameters set.

For example: IP

maskgateway is empty.

DNS empty.

Other computers are also connected to the switch (hub), and the network card parameters are set.

For example: IP

maskgateway

DNS Then, establish an Internet connection on the XP to ensure that you can access the Internet, open the attributes of the online neighbor, and share the Internet connection.

Note that sometimes firewalls block sharing.

Of course, third-party shareware is also available, but it is not recommended to use it because there are few machines.

It is recommended to use TP-LINK410 router + TP-LINK8 port 10 100M adaptive switch, the former ** is about 200, the latter ** is also about 200, plus the network cable of ten machines, the average is calculated according to 50 meters, is 500 meters, 1 meter is about 900 yuan in total.

Switches and routers with D-Link!

Connect all the cables to the switch, and then connect the Internet cables to the server!

How to set up an Internet café network and a local area network? 1

Routing, network cables. Network card. Set up a computer as the main unit. Others are from. Just connect it and set the IP address in turn.