-
It may be that there is a bad contact on the line.
Please find a professional to overhaul as soon as possible.
Safe to use is the safest.
Wishing you health and happiness.
-
Your home is a square aluminum wire, and the line is long, the internal temperature of the soymilk machine is halfway through the work The relay of the control circuit to control the heating tube is the process of powering on for 1 second and powering off for one second, in order to maintain balanced heating and easy to stir the design, due to the current change in this process and the slight fluctuation of the voltage due to the loss of your line, causing the light to flicker But in the case that the socket line in your home can withstand 6 amp current, there is no problem without worrying.
-
As soon as the soymilk machine turns, the lights at home also flash, indicating the voltage of the soymilk machine. The voltage in the home is unbearable, and it may be that the circuit in your home has a short circuit, so you still have to ask an electrician to help you check and repair it.
-
The soymilk machine starts to rotate, and the starting current required is relatively large, which affects the lights at home, if you pay attention, the refrigerator. The light of the washing machine will also flash when it is started, especially the air conditioner, and the light will flash even more.
-
If the soymilk machine is rotating, the house is also flashing, it proves that the power in your house is relatively large.
-
This is the amount of current that needs to be increased when the soymilk machine starts.
-
Because the moment the soymilk machine rotates, it consumes a lot of power, the current is very large, and because the wire also has a certain resistance, the voltage of the wire is increased instantly, and the voltage of the lamp at home is instantly reduced, resulting in a flash.
-
The nutrition of soy milk is very rich, so adults and children like to drink, but the soy milk purchased outside may not be clean, and some things are added, if you give it to the child to eat, I am worried that there will be any bad effects, so many people like to buy a soybean milk machine and drink it themselves. No matter what kind of soymilk machine you use, there may be some faults during use, so what is the fault of the soymilk machine that keeps calling the lights after plugging in and pressing the start? file or.
The soymilk machine is plugged in and pressed, and the light keeps flashing, which may be that the water temperature is too high or a small amount is too little. There is also a need to see if the soymilk machine has a micro switch.
If there is a micro switch, it must be topped up, and it is also necessary to check whether there is any water. If the internal program does not work properly, it will also slow down the situation, you need to remove the parts that can be disassembled, and clean the dust inside, if it still doesn't work, you can only take it to the repair shop to repair.
In the process of using the soymilk machine, the indicator light has been flashing non-stop, causing the machine to not work normally, check the water level, not too high or too low, should meet the required standards. At the same time, you also need to see if the lid on the soymilk machine is well covered, and when some soymilk machines are used, the lid is not covered correctly and cannot work normally.
In short, there will be some differences in the functions of different types of soymilk machines, read the instructions carefully before operation, and operate them strictly in accordance with the instructions, so as not to cause early damage to the machine due to improper operation.
-
Hello dearThe light keeps flashing after the soymilk machine is started, which may be due to problems such as high water temperature, less water, less bean material, water ingress into the head, and damage to the motherboard. 2.
When the indicator light of the soymilk machine is fully lit and flashing, see if there is a micro switch, and if there is a micro switch, you should top the micro switch. You can also check whether the water is ingress or not, and if the water level is not reached, if it still doesn't work, change a membrane switch. 3.
It can be ruled out by following this procedure: check if the water level is too high or too low; Check whether the lid is well covered with socks and check the internal water temperature smoothly to see if water more than 70 degrees has been added to it; Check the circuit for defective component performance. 4.
Generally, the soybean milk machine can be made, and the five elders change the soybean milk, whole soybean milk, fruit and vegetable soybean milk, and corn juice. The machine has the functions of automatic cleaning, automatic heating and pulping.
-
There are several possibilities:
1. Drain too much water, or too little. Generally, the water level can be seen in transparent cups. Pay attention to the amount of water discharged.
2. The head of the machine is not stable, and the wall is not sealed, and the light will flicker after the power is turned on, and the alarm will be issued from time to time.
3. Water ingress into the machine head, resulting in damage to the circuit board, this situation is recommended to be directly taken to the after-sales repair, non-professionals should not disassemble without authorization.
When purchasing a soymilk machine, you can choose a soymilk machine with different capacity according to the number of people in the family, if it is one or two people, it is recommended to choose 800 1000ml; If it is three or four people, it is recommended to choose 1000 1300ml; If there are more than 4 people, it is recommended to choose a 1200 1500ml soymilk machine.
Selection tips: 1It has intelligent non-stick and easy-to-clean technology.
2.The performance of the motor and the design of the blade are reasonable.
3.Good mesh mesh holes are arranged in a herringbone shape, dense and even.
4.The lower half of the heating tube of the ideal soymilk machine is a small semicircle, which is easy to wash and unload the net cover.
5.The best time to delay the cooking time after the first boiling of soy milk is 4-5 minutes.
6. The combination of factors such as the ratio of bean amount to water, the water temperature of refining, the time of refining, and the time of boiling.
-
There is no water, or the location is not put right.
-
Short circuit, high power supply voltage, no water discharge.
-
Ah, what brand did you buy, maybe it was a short circuit, etc., you go and read the manual carefully.
-
Problems with the motherboard power supply.
Or it's a problem with a microcontroller, and you're checking to see if your power supply is working.
-
Hello, the soymilk machine has been plugged in and pressed the problem that all the lights are flashing after starting, which may be caused by the following reasons: 1The temperature inside the machine is too high, which causes the protection device to start quietly.
In this case, you can wait for the machine to cool down before restarting. 2.There was a malfunction inside the machine, which caused the protection device to activate.
In this case, you can check the machine for loose or damaged parts, or clean the inside of the machine before restarting. 3.The machine's power supply line failed, causing the protection device to activate.
At this time, you can check whether the power line is normal, or replace the power line, and then restart it. In short, when the soymilk machine fails, you can first check whether there are loose or damaged parts inside the machine, or clean the inside of the machine, and then restart it. If the problem persists, it is recommended that you contact the after-sales service center for repair.
-
Dear users, the soymilk machine has been plugged in and pressed the start, and the lights are all flashing, which may be the following faults: 1Power failure:
There is a problem with the socket or power cord of the soymilk maker, which causes the power supply to be unstable and the soymilk maker cannot work properly. 2.Motor Failure:
The motor of the soymilk machine is damaged or there is a problem with the motor drive circuit, which causes the soybean milk machine to not work normally. 3.Water level sensor malfunction:
The water level sensor of the soymilk machine is damaged or there is a problem with the sensor line, resulting in the soymilk machine being unable to detect the water level and thus not working properly. 4.Control Board Failure:
The control panel of the soymilk machine is faulty, resulting in the soymilk machine not working properly. If the above faults occur in your bean weighing machine, it is recommended that you contact the after-sales service center or professional maintenance personnel for maintenance and maintenance. At the same time, it is recommended that when you use the soymilk machine, follow the operation steps on the manual to avoid failure caused by improper operation.
-
Hello, glad to answer for you. <>
The soymilk machine keeps calling after plugging in and pressing the start, and the indicator lights are all flashing, which may be that the soymilk machine has failed. The common causes of failure are as follows: 1. The control panel at the bottom of the soybean milk machine is faulty
There was a problem with the electronic components on the control board of the Zheng nationality department at the bottom of the soymilk machine, which made it impossible to control the normal balance shed. 2. The power supply voltage is too low: check whether the power supply connected to the soymilk machine is stable, if the power supply voltage is too low, the soymilk machine may not start normally.
3. The water level sensor is damaged: the water level sensor can identify the water level when it is soaked in water, and if it is damaged, it may misjudge that the water level is insufficient, resulting in failure to work normally.
-
Summary. It should be a short circuit in the power strip inside the soymilk machine. The control panel is malfunctioning and cannot be operated.
Suggestion: Please ask professional electrical maintenance personnel to disassemble and detect the specific damage part. repair office as well and resolved.
1. If the alarm occurs within 10 minutes after power-on, you need to check whether the water level in the cup is between the highest and lowest water levels; The temperature of adding water should not exceed 70 degrees. 2. If the alarm is called after ten minutes, it is related to the placement of ingredients, you can consult the use of ingredients, if the ingredients are not easy to foam, it will cause this phenomenon. The amount of water discharged does not meet the regulations.
There is a water level in the Midea soymilk machine, and the amount of water in the Midea soymilk machine must be in the water line when it is working, and it is not too high or too low. You can check the amount of water in it to see if there is a problem that the water is too high or too low.
1. Whether the temperature of the water added is too high, if it is higher than 70 degrees, there will be such a situation, it is recommended that the user change the water. 2. The amount of water added is too small to take the liquid, please add it to the ambush room between the two water lines. 3. If the bean feed is added too little, the user needs to operate according to the food consumption chain spectrum and put more bean feed.
It should be a short circuit in the power strip inside the soymilk machine. The control panel is malfunctioning and cannot be operated. Recommendations:
Please ask professional electrical maintenance personnel to disassemble and inspect to find the specific damaged parts. repair office as well and resolved. 1. If the alarm occurs within 10 minutes after the power is on, it is necessary to check whether the water level in the lower cup is between the highest and most observant low water marks; The temperature of adding water should not exceed 70 degrees.
2. If the alarm is called after ten minutes, it is related to the placement of ingredients, you can consult the use of ingredients, if the ingredients are not easy to foam, it will cause this phenomenon. The amount of water discharged does not meet the regulations. There is a water level in the Midea soymilk machine, and the amount of water that is not transported in the Midea soymilk machine must be in the water line when it is working, and it is not too high or too low.
You can check the amount of water in it to see if there is a problem that the water is too high or too low.
-
Hello, dear dear, the soymilk machine has been called after the start, and the lights are all flashing, what is the fault, the soymilk machine has been plugged in and pressed, and the lights have been flashing after the start, which may be that the water temperature is too high or a small amount is too little. If there is a micro switch, it must be topped, and it is also necessary to check whether there is any water. If the internal program does not work properly, this situation will also occur, you need to remove the parts that can be disassembled, and clean the dust inside, if it still does not work, you can only take Cong to the repair shop for repair.
Hope mine can help you; Once again, I wish you good health and a good mood!
Please follow the following procedure to complete the transfer procedure: >>>More
It's best to kill monsters that are 5 to 15 levels higher than you, depending on your equipment. Turn around and add 1000 more attribute points. 80 more skill points
Because this song is generally learned when I was in school, when I was relatively young, there was no pressure on life and happiness, and now for me, every time I hear this song, I can feel the joy of when I was a child, and now my life is more stressful, so every time I hear this song, I will have a faint sadness. This song is also performed for adults at the annual June 1st party. Children's Day is the busiest day for children, and it is also the most tiring day.
The preliminary judgment is that the bald head is broken.
There are three definitions of planets: 1. The mass is large enough to become a sphere. 2. Planets must revolve around one of their parent stars. >>>More