How to solve the problem that the speaker is a little watery iPhone ?

You can spin it dry as much as possible first, and then dry it with a dry cloth. Finally, let it dry in a ventilated place.

How to deal with the water after the iPhone is ingressive.

1.Turn off the phone as soon as possible, cut off the power, and do not try to turn it on again to avoid causing a short circuit in the motherboard.

2.Remove the SIM card and use a tissue or cloth to remove water from the outside and crevices of the phone.

3.If there is light water ingress, you can wrap the phone with a paper towel, put it in a bag and put it in a small bag of desiccant.

4.The mobile phone cannot be turned on after entering the water, most of the chips such as the motherboard and CPU are short-circuited and burned, and it is recommended to send it to the after-sales service center for repair immediately.

Don't try the following wrong methods after your phone gets into water.

1.Don't shake your phone too hard. Because under the constant shaking, the liquid will swim inside the machine, and the moisture may enter deeper and burn the internal chip of the machine.

2.Don't use the hot air of a hair dryer to dry your phone for a long time. iPhones are now all metal bodies, and metal conducts heat easily, which will blow off the solder joints of the motherboard inside the machine, causing the motherboard to malfunction.

3.Do not attempt to charge a phone that has been flooded. An iPhone that gets into the water may have water stains inside, which can burn out the motherboard when it is powered on and cause a more serious failure.

4.Do not leave your phone in water for a long time. In the case that it cannot be used normally after two or three days after general treatment, it should be sent for repair immediately, and long-term placement will cause the motherboard to be corroded, or even unable to be repaired.

The water ingress of the iPhone speaker, the method of treatment and the detailed operation steps are as follows:

1. First of all, booting up may cause a short circuit in the mobile phone, and it should be turned off immediately, as shown in the figure below.

2. Secondly, take out the mobile phone ** card and memory card with a card pickup needle to avoid damage, as shown in the figure below.

3. Next, use a dry paper towel to absorb the moisture around the speaker, as shown in the figure below.

4. Then, shake the water vigorously until the water cannot be shaken out, as shown in the figure below.

5. Finally, use a hair dryer to blow the speaker, but keep a certain distance, as shown in the picture below, and wait for it to dry.

How to solve the problem of noise when the speaker of the apple mobile phone is flooded, after the mobile phone is flooded, there will be a little water backlog in the speaker, you can first put the speaker down, hold the phone and shake it a few times. Then wipe the speaker hole with a paper towel. Use a hair dryer to turn on the hot air and blow it on the speaker, don't blow it for too long, just about a minute.

If it is caused by water, it is recommended that users use a paper towel to wipe the speaker of the mobile phone, pay attention not to use force, and after making sure that there is no water, put the mobile phone in a cool and ventilated place to dry, and pay attention not to use the mobile phone during the period. If this situation occurs after it has been dealt with, it means that it is a hardware failure, and it is recommended that the user directly contact the after-sales service for relevant testing, or find a mobile phone repair shop to clean up the speaker or replace the speaker. Here's how to fix it:

1. After the mobile phone enters the water, there will be a little water in the speaker, you can first turn the speaker down, hold the mobile phone and shake it a few times. 2. Then wipe the speaker hole with a paper towel. 3. Use a hair dryer to turn on the hot air and blow it on the speaker, don't blow it for too long, just about a minute.

1. Fish it out of the water as quickly as possible.

2. Turn off your iPhone immediately. Once your iPhone falls into water or gets into it, disconnect it immediately. Because the damage to mobile phones is often not caused by water itself, but by short circuits of internal components triggered by water, or even further cause the components to burn out or the battery**.

3. Remove all parts of the iPhone that can be removed as much as possible, such as the back cover, SD card, SIM card, headphone jack plug, etc., so that the moisture in the iPhone can be fully dissipated as much as possible. The screen protector can not be removed unless you see visible blisters inside.

4. Dry your iPhone with a cloth, as dry as possible, you can wipe the screen, sides, and back with a cloth (t-shirt, socks, etc.) or absorbent materials. Pay special attention to the power buttons, volume buttons, mute switches, speakers, microphone, and audio output jacks, and try to wipe all visible moisture as much as possible.

5. If you can change it for the first time, try using a cotton swab to absorb excess water from the audio output jack and small slits.