What should I do if E2 appears as soon as the washing machine is turned on?

The general problem is that the water does not enter, or the lid is not properly covered, or the outlet is blocked; Check whether it is caused by the failure of the faucet, drain pipe or the door of the washing machine itself and not closing tightly; There is a high probability of clogged drainage, and if you confirm that there is no problem with the water inlet and the cover, it is a drain problem.

Automatic washing machine bai display E2: refers to the drainage timeout (draining water for more than 6 minutes, the alarm can be lifted by opening and closing the door cover once).

Troubleshooting DAO Method:

1. Check to make sure that the drain pipe has been lowered.

2. Check whether the drain pipe is deformed or twisted.

3. Check whether the drain pipe is unblocked and whether there are any foreign objects blocking the drain pipe.

4. The above three points are all common reasons for the washing machine not draining or draining slowly, if it is caused by these faults the washing machine not draining, then it can be easily eliminated.

5. After eliminating the drainage fault caused by the above drainage pipe, if the washing machine still does not drain, adjust the washing machine program to single dehydration, and then start the washing machine.

6. If there is a suction sound, it means that the circuit and drainage solenoid are normally engaged.

7. Next, you should check whether the drain valve of the washing machine is blocked, determine whether the tension spring of the drain valve falls off or whether it is rusted and broken, if these situations occur, it is recommended to clean and replace the damaged parts.

8. If the washing machine has no suction sound, it may be that the circuit is faulty, at this time, the rear cover should be opened to check whether the drain solenoid plug-in wire falls off, if it does not fall off, use a multimeter to measure the resistance at both ends of the drain solenoid, if the resistance value is infinity or less than 30 ohms, it means that the drain solenoid has been broken and short-circuited, and it is recommended to replace it.

9. If it still does not work properly after replacement, it may be due to the burning of the drainage electromagnet that causes the failure of the program controller (generally the thyristor that controls the drainage), and it is recommended to overhaul the controller.

There are two possible faults in the washing machine with E2:

1. Because the upper cover is not covered, you can open it to check whether there is a big beard and clothes clamped, or other foreign objects that affect the normal closure of the cover.

2. Because of the overtime of drainage, you can check whether the drainage pipe is deformed or twisted; Check that the drain pipe is unblocked and that there are no foreign objects blocking the drain pipe.

The troubleshooting method of washing machine can not be dehydrated is as follows:

1. The washing material is in a state of rolling imbalance during washing. Elimination method: You can put a small amount of clothes before washing clothes, and don't stuff too much at once, so as not to cause imbalance during washing. And the effect of dehydration is not good.

2. The safety switch on the top cover of the washing machine is damaged. Try not to open the top cover during the dehydration process to avoid damage to the top linkage switch.

3. The drainage system of the washing machine is blocked. Removal method: remove the drain filter for cleaning, flush the drain with water and remove the debris in the drain valve.

4. The water level switch cannot be reset. Solution: Contact the after-sales point.

Hello, glad to answer for you. Dear, the automatic washing machine shows E2 refers to the drainage timeout, then the alarm can be lifted by opening and closing the door cover once. When using, it is necessary to check that the drain pipe has been put down, that the drain pipe is not deformed or twisted, and that the drain pipe is unblocked and that there are no foreign objects blocking the drain pipe.

One is that the lid of the washing machine is not properly covered, in this case, it may be considered that there is a foreign object, which affects the normal closure of the lid.

In the second case, it may be that the drainage is overtimed, check whether the drain pipe is deformed or blocked, if there is a deformation or blockage problem, then we need to dredge the drain quickly.

Reason for showing E2: The lid on the washing machine is not closed when it is running. Workaround:

Open the lid when the washing machine is running, and the machine will report E2 to prompt the user to close the lid; If the E2 alarm still appears after closing the lid and restarting, check that there is a small magnet on the right side of the transparent cover to control the reed switch in the tray base to see if the small magnet has fallen off or the reed switch is broken; You can also consult professional after-sales personnel.

Expand: Common sense of washing machine maintenance.

1 The washing machine should be carefully read before use. When in use, the potato scrap filer should be placed on a flat and solid ground, and the distance from the wall and other items must be kept at least 5 cm.

2. Washing should be classified and washed in batches according to the material, color, and degree of dirt.

3. Before washing, remove the debris in the pocket to prevent hard objects such as nails, coins, and hairpins from entering the laundry bucket; If there is sediment, the number of clothes and messy objects should be removed from the sediment and then put into the laundry bucket; Wool should be washed in a yarn bag.

Summary. The washing machine just turned on the power and the alarm appeared, and the display screen appeared E2, what happened?

Washing machine E2 failure** refers to the draining timeout, and the washing machine will sound an alarm after draining for more than 6 minutes. Check whether the lid of the washing machine is not closed or closed tightly, and try to close it again to remove the alarm; Check the drain for foreign objects and try to clean the drain before draining. If the above reasons are ruled out, it may be that the washing machine sensor or drain valve is faulty, and you need to apply for after-sales repair.

Here's the details: The washing machine shows an E2 fault**: This refers to the drain timeout, and the washing machine will be alerted if it drains for more than 6 minutes.

It may be that the lid of the washing machine is not closed, try to re-close and lift; If it still can't be removed, check to see if the foam is clogging the drain due to too much laundry detergent, or if other clothing is causing the drain to clog.

If the drain valve may fail, adjust the washing machine program to single dehydration, and then start the washing machine, at this time, pay attention to whether the drain solenoid has a [pop] suction sound; If there is a suction sound, it means that the circuit and the drainage solenoid are properly engaged, and if the washing machine has no suction sound, it may be that the circuit is faulty;

If above. The washing machine just turned on the power and the alarm appeared, and the display screen appeared E2, what happened?

The washing machine just turned on the power and the alarm appeared, and the display screen appeared E2, what happened? Washing machine E2 failure** refers to the draining timeout, and the washing machine will sound an alarm if the water drains for more than 6 minutes. Check whether the lid of the washing machine is not closed or closed tightly, and try to close it again to remove the alarm; Check the drain for foreign objects and try to clean the macro limb drain before draining.

If the above reasons are ruled out, it may be that the washing machine sensor or drain valve is faulty, and you need to apply for after-sales repair. Here's the details: The washing machine shows the E2 fault code:

Refers to the draining timeout, and the washing machine will be dehydrated for more than 6 minutes, and an alarm will appear. It may be that the lid of the washing machine is not closed, try to re-close and lift; If it still can't be removed, check to see if the foam is clogging the drain due to too much laundry detergent, or if other clothing is causing the drain to clog. If the drain valve may fail, adjust the washing machine program to single dehydration, and then start the washing machine, at this time, pay attention to whether the drain solenoid has a [pop] suction sound; If there is a suction sound, it means that the circuit and the drainage solenoid are properly engaged, and if the washing machine has no suction sound, it may be that the circuit is faulty; If above.

Cover the lid well.

This is supposed to show up incorrectly** may be caused by not closing the lid properly, you check it out.