How to connect electric guitars and effects to home stereos? I don t have an amplifier.

Updated on number 2024-04-01
4 answers
  1. Anonymous users2024-02-07

    I didn't understand this problem on the first floor.,He doesn't have an amplifier.,So you can only say that the guitar and the speaker are connected from a physical point of view.,It's not going to make a sound at all.,The landlord is a strong man.,I thought I'm strong.,My connection method is,The guitar --- connection cable --- the conversion head of the college and the small --- the computer --- through the guitar

    rig3's soft effects are output to the --- amplifier--speakers (the odd sound amplifier and speaker I bought when I got married have been idle, and I want to sell it to the damn man who collects it for 5 yuan to collect me, and I bought it for thousands when I bought it) The landlord is stronger than me in the absence of an amplifier to make the guitar sound, it seems a little difficult, because the power output of the guitar can't directly drive the speaker at all, and I personally feel that it is best to connect like this.

    Guitar - *** or VCD microphone jack (don't say there is no *** at home) and then connect to the speaker from *** or VCD to make up the pair, at least it can sound, but don't expect the sound to be good, you can only do the volume is larger than not plugged in, because *** or VCD microphone jack amplifier effect is equivalent... Rotten.

    I can't follow the post.,So on the third floor.,I found an old innovation in the computer city 4620**30 yuan.。 Delay needs to be patched.,You can search for an asio4all patch to install it will make a big difference.,If you change an innovative sound card, it will improve a lot.,If it's not good, you can add me qq and I'll study it with you (but be sure to indicate the intention.,Strangers don't thank you)

  2. Anonymous users2024-02-06

    It's very easy to buy a regular guitar cable and a plug (most of them are plugs that work with your home speakers), and these are easy to buy. Then just replace one end of the cable with that plug

  3. Anonymous users2024-02-05

    2nd floor, how much is your sound card? I got down to guitar

    rig3 doesn't work.,The sound that popped up was delayed for 3 seconds before it ran out of the stereo.,Sad.。

    Landlord,Home stereo can't be directly connected to the guitar,To change the circuit inside,For example, bias resistance,Electric guitar can not use bias resistance,Electric box guitar should be bias resistor,(not too small,Otherwise, it will burn out the pickups) and then connect with the audio。

  4. Anonymous users2024-02-04

    Summary. Dear, I'm glad to answer for you! Connect the electric guitar to the sound system by following these steps::

    1.First, make sure you have an electric guitar and a sound system. 2.

    Prepare a 1 4" plug (also known as plug) to dual RCA plug audio cable. If you only have a single RCA plug audio cable, you can use a 1 4-inch plug to a single RCA plug converter. 3.

    Plug the 1 4-inch plug into the output jack of the electric guitar. Usually it is located underneath the electric guitar, near the volume and tone control knobs. 4.

    Connect the RCA plug on the other end to the audio input jack of the sound system. Usually, these jacks are located on the back or side of the speaker and are labeled "Input" or "Audio Input". 5.

    Dear, I'm glad to answer for you! Connect the electric guitar to the sound system by following these steps:1

    First, make sure you have an electric guitar and a sound system. 2.Prepare a 1 4" shipping plug (also known as plug) to dual RCA plug audio cable.

    If you only have a single RCA plug audio cable, you can use a 1 4-inch plug to a single RCA plug converter. 3.Plug the 1 4-inch plug into the output jack of the electric guitar.

    Usually it is located below the electric guitar, near the volume and tone control knobs. 4.Connect the RCA plug on the other end to the audio system's knob audio input jack.

    Usually, these jacks are located on the back or side of the speaker and are labeled "Input" or "Audio Input". 5.Turn on the sound system and set it to the correct audio input source.

Related questions
8 answers2024-04-01

Summary. Hello, I'm glad to ask you this question, the brand of the guitar is generally on the headstock, and you can also see the brand and model through the sound hole. >>>More

6 answers2024-04-01

Climbing the lattice is a long-term project, and many masters at home and abroad have climbed it for a lifetime. >>>More

17 answers2024-04-01

Any ** in Devil May Cry can be played gorgeously, depending on how you play. >>>More

16 answers2024-04-01

Hello, the earliest and most classic brand in the history of the development of electric guitars"Gibson"When he was invented, there was no vibrato system, it was a fixed bridge, the electric guitar at that time had not even invented the effect, naturally there was no need for such a fancy part of the vibrato system, but as the most classic piano in the world, his design was retained, and no tremolo system was added later, the vibrato system was originally manufactured when there was only a single shake, and then there was a double shake, but the double shake has high requirements for the bridge system, and the low-grade double shaker often runs for this reason. >>>More

16 answers2024-04-01

Of course not.

There are three main buttons on a typical electric guitar: volume, tone, and pickup selector. And the sound emitted by your electric guitar is also particular about the sound source, if the sound source is out of tune, the later effects can only "make the wrong mistake". >>>More