HOME BROADBAND: AFTER USING THE D LINKDIR 655 WIRELESS ROUTER, THE NETWORK SPEED CHANGES FROM 4M TO

It is recommended that the landlord try to change the WAN port rate of the router to 10Mbps to try, click "Advanced" - Advanced Network Settings" in the management interface, and find that the "WAN port rate" is changed to "10Mbps".

1.First of all, I want to tell you: D-link7100 is not a wireless router, and the speed you test must be the result of the test after connecting the computer with a network cable; Secondly, the Link DIR-655 is a wireless router, and from yours, it can be inferred that it is the result of your test when using a wireless connection; Again, you need to know:

The wireless transmission rate is much slower than the wired connection rate. The results will naturally be slow.

2.As for the disconnection situation you mentioned, I can tell you: it is the hardware of this router (Link DIR-655) that is a problem.

3.If you don't feel that wireless brings you a lot of convenience, switch back to the original router.

The normal thing is that the wireless router definitely doesn't have a speed block of wires !It doesn't matter if the landlord is there!

The problem may be related to the router! Since you can access the Internet, the setup is definitely no problem!

Wireless routers, the speed will drop in case of a bad signal.

The route is limited in speed, find Telecom 10,000 to solve it.

The wireless mail device is not encrypted, and it will be connected by the outside wifi.

If you suspect that your Wi-Fi has been stolen and you don't use Wi-Fi, you need to find the Wi-Fi settings and turn off Wi-Fi in the settings options, so that no one else can steal your Wi-Fi.

In addition, you can allocate the appropriate amount of traffic to each machine within the traffic limit, so that one machine will not be disconnected because one of the machines is taking up a lot of traffic.

In addition, if you are a user who has a limited time to access the Internet every month, please pay attention to the choice of connection mode in the manual configuration interface, the connection mode is generally automatic connection by default, that is, as long as the router is turned on, the network will be automatically detected, and if the connection to the network is normal at this time, it will be automatically connected to the Internet, regardless of whether you turn on the computer to surf the Internet, so please also turn off the power without using the router, so as not to cause high network costs.

Good luck!

Method: [Home Network Environment Wiring]:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoE Dialing] (some are ADSL dialing), enter the username and password (provided by the network service provider) according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

Turn on the router's wireless function].

1. Select Wireless Settings --- Basic Settings.

2. Check [Turn on wireless function] and click Save.

Set wifi password].

1. Wireless Settings - Wireless Security Settings - Select [WPA-PSK WPA2-PSK].

Authentication Type: Automatic.

Encryption algorithm: AES.

The PSK password is the wireless password. Set the required password.

Manually changing the IP address of one of the computers will solve the problem.

Didn't you dial in with a router?

And is there a conflict of IPs?

The speed of Internet access is not unrelated to the hardware of the computer or mobile phone, but it has little to do with it.

The speed of Internet access is mainly related to the following factors:

One is the transmission medium; The second is the transmission rate. At present, the medium of the backbone network is optical fiber, which is the best medium at present, and most places have realized optical fiber to the home, so the medium of the backbone network is beyond question. The problem is that the quality of the indoor line is worth it**, although it has been fiber-to-the-home, but the network speed from the indoor to the terminal is 4m.

In addition, the transmission rate is related to the service provider, fortunately, China Unicom has entered the 4G era, and other service providers are also improving their network speed, which is also good news for users. But China's internet speed ranks 98th in the world, why? I think most of the reasons are:

First, the line is aging, the quality is not high, the layout is unreasonable, and the key is that the "last mile" problem has not been solved; The second is that the maintenance service can not keep up, many service providers only know the charge, but less service quality improvement; Third, from an objective point of view, China has a large number of users and relatively many problems of network congestion.

Judging from your situation, it should be a problem with the router, try it with good quality and function.

Good luck!

There may be a problem with the network cable, I don't understand hi me.

I thought that the wide loan was with wireless and wired, and if you don't understand, you can find me.

Broadband account encryption, right? Can I use the dial-up connection that comes with the system?

If possible, upgrade the router firmware and test it.

The first step is to connect the line according to the connection method between the router and the cat.

The second step is to enter the address you see on the router in your browser, which is usually.

Then enter,Enter the corresponding account and password,Generally, the newly bought admin is confirmed to enter the operation interface。

Since the address of the fiber modem and the wireless argument router are the same, it will cause conflicts, so you need to modify the location of the router, set the LAN port in the network parameters to modify the IP address as shown in the figure, click Save, and restart the router.

Step 3: Click on the setup wizard, click on the next step, enter the Internet mode setting, we can see that there are three options for Internet access, if your home is dial-up, then use PPPOE. Dynamic IP can be used directly by plugging the computer into the network, and there is a DHCP server on the upper layer. The static IP is generally a private line or something, or it may be a cell bandwidth, etc., and the upper layer does not have a DHCP server, or wants to fix the IP.

I chose PPPoE because I dialed. (It is recommended that you choose to let the router automatically choose the Internet access method).

If you choose PPPoe dial-up Internet access, you need to fill in the Internet account and password, which should be understood by everyone, and there will be an account number to open broadband, and it is OK to fill it in

Then the next step is to enter the wireless settings, we can see the channel, mode, security options, SSID, etc., generally SSID is a name, you can fill in as you like, and then the mode mostly uses 11BGNFor wireless security options, we need to choose WPA-PSK WPA2-PSK, which is so safe that it will not be hacked and rubbed by the network.

The next step is to set it up successfully.

Click Done, and the router will automatically restart, so be patient. The interface that appears after success.