What to do if the length of the wire cut out by the computerized wire stripping machine is different

1. Press or move the cursor to select a program after powering on.

01 89 is the regular program, 90 99 is the super ** program).

5. Press the line to be stripped into the middle of the wire wheel, adjust the wire wheel to make the gap open to the most suitable position (note: it is better to hear the or slight internal screw impact sound when working), and then take out the line and adjust the gap adjustment wheel of the incoming line wheel, so that the gap between the incoming wheel and the gap between the outlet wheel is comparable.

6. Thread the thread into the wire inlet and the wire wheel, pass through the conduit and then pass through the knife edge, then move the cursor to the wire diameter on the second page of the program, press the stop button, the two knives will tangent to each other, and then take out the line to check the incision, if the wire skin is not cut through, reduce the wire diameter value, if the copper wire is cut, then increase the wire diameter value. Or adjust the value of the wire diameter according to the situation when stripping the wire, reduce the wire diameter value when the wire head or wire end cannot be peeled, and increase the wire diameter value when the copper wire is completely cut off or cut a few.

7. Usually the retract value of the wire below the square is between 01 and 05, the thinner the wire skin, the smaller the retract, and the general wire can be set to default (the default retract is 08).

8. Press the run button to start the test stripping, (the first one should pass through the knife edge before starting to strip the line, and at the same time check the position of the catheter mouth should be in the middle of the upper and lower blades to avoid the unsmooth incoming line, when the value of the stripping tail is greater than 10, the catheter needs to be moved back slightly to make the end of the line achieve the best effect).

9. The quantity can be set according to the actual quantity required, the output is preset to 0000, and the machine stops working when the output = quantitative.

10. Press the run button to start production.

Maintenance Precautions:

1.Please add an appropriate amount of oil to the oil filling hole of the turret regularly to maintain lubrication to reduce noise and prolong the service life of the machine, preferably once a week

2.When replacing the blade, you need to turn off the power and remove the tool holder, after replacing, align the slotted slot of the knife holder rotation shaft and install it in situ, and then rotate the rotation shaft after the tool holder by hand to rotate smoothly and then tighten the screws on the tool holder (Note: to avoid the installation position deviation system prompts the tool holder can not reset the error message), if the system prompts the tool holder can not reset the error message, please adjust the knife edge position, please refer to the knife edge position adjustment method on page 10 11 of the manual for specific adjustments.

Regularly clean the dirt on the incoming and outgoing wheels to ensure the quality of the stripping effect, if there is a phenomenon of different stripping lengths, there may be dirt on the wheels and slip, at this time it needs to be cleaned.

Top Grab a Like See all 3.

Then you can find the cause of the problem.

Summary. Dear

1. It may be that the gap between the incoming transmission wheel is too large, and sometimes the wire head can not be peeled, and the line that cannot be stripped at the end of the wire is greater than the set line length, and the "incoming line clearance adjustment wheel" is adjusted to increase the pressure.

2. Adjust the pressure of incoming transmission.

3. If there is stolen goods in the wire pipe, it is also possible to cause this situation, and it needs to be properly cleaned.

You can check it by referring to the above questions.

What should I do if the length of the wire cut out by the computerized wire stripping machine is different?

Pro-1, it may be that the gap of the incoming transmission wheel is too large, and sometimes the wire head can not be peeled, and the line that the wire head cannot be stripped is greater than the set line length, and the "incoming line clearance adjustment wheel" is adjusted to increase the pressure. 2. Adjust the pressure of incoming transmission. 3. If there is stolen goods in the line pipe, it is also possible to cause this situation, and it is necessary to carry out appropriate cleaning and cleaning.

You can refer to the above questions to check.

Dear is very happy to serve you, if you are satisfied with this service, I hope to click to end the service, give a thumbs up. Have a great day!

Adjust jumper springs, general computer sewing.

The machine automatically trims the thread in 2 cases, 1After sewing, the sewing machine automatically trims the thread 2After sewing, the operator presses the thread trimming button to cut the thread. Generally, the manufacturer will help you set it up.

You can check the position of the loose wire ejector pin on the loose wire ejector rod. The sewing machine is sewing at the highest speed, the end face of the loose thread ejector rod pin falls on the plane of the loose thread ejector rod, and the thread clamp works. In the low-speed sewing state, the end face of the loose thread ejector rod pin still falls on the plane of the loose thread ejector rod, but it is close to the inclined plane of the loose thread ejector rod.

In the state of trimming and parking, the end face of the loose wire ejector pin falls on the plane of the loose wire ejector rod, and the wire clamp floats and does not work.

It may be that the noodle thread is tight, and you can loosen the control noodle threader to see.

Adjust the jumper spring to check the position of the loose wire ejector rod pin on the top of the loose wire. At the highest speed of sewing, the end face of the loose thread ejector rod falls on the plane of the loose thread ejector rod, and the thread clamp is working. In the low-speed sewing state, the loose thread rod still falls on the plane of the loose thread ejector rod, but it is close to the inclined plane of the loose thread ejector rod.

Just press the end of the thread every time you start it.

Pull the thread before cutting it each time.

It should be adjustable and narrow.。。。

Adjust the noodle thread a little looser, that is, adjust the screw of the cable.

It's adjustable, I've seen it.

First of all, see if the line is in the wire clip

Continue to hurry up, hurry up, hurry up, see you, send fast, send fast, pay the room fee, economic Daji punch in, oh, I'm afraid of leeks, eggs, what time will I call you fat cow rice, you.

Hello. Dahao computer embroidery machine, old thread trimming.

You've tuned up your computer.

Then tune the mechanical one. First of all, loosen the thread a little so that the thread is longer and the needle will not be dragged out of the pinhole.

Computer embroidery plate making, training computer embroidery plate making, computer embroidery machine maintenance, I am very professional. Any questions you have are always available.

Thank you. <>

The lower the number of the XD-200 computerized wire cutting and stripping machine, the deeper the blade will be cut, and vice versa.

XD-515 Computerized Wire Stripping Machine It is the smaller the number is shallow and the deeper the number is cut, and you can understand it after a few attempts.

Retracting the knife is the size of the knife opening, and you will understand it if you observe it.

The latest electronic products tend to be light, thin, short, and small, so the wires are also more and more thin, ** and high-precision, and this machine can just give full play to its greatest strengths.

In the past, it was regarded as difficult to process within 50mm, but now there is no difficulty, even when the total length is only 1mm, both ends can also be peeled at the same time, and at the same time, they can be set up separately to send the line, feed, retract, peel and peel speed, for the isolation line can also be forced to peel to 99mm, eliminating the problem that the isolation line can not be fully peeled and hurt the heart line.