The problem of assembling a computer for the first time, what will happen to a novice who assembles

It just so happened that my Internet café cleaned up the server yesterday and there was a similar problem.,It took more than an hour to find the reason.,Hehe.。

1.You have to figure out whether it is booted into the system or restarted after entering,The reasons for the two are absolutely different,If you get to the step of the XP screen,It's definitely a software failure,Not to mention reinstalling。

Like you said, it seems that it restarted without a POST, and that's the hardware reason.

2.There are several possibilities, one is that there is a problem with the power supply, such as the power is small and the power cannot be brought to the full power required by the hardware;

3.There is also a possibility that if there is a short circuit in any hardware, or if the wrong wire is connected, the fan will automatically turn as soon as the power is turned on without pressing the power button, and the power will be cut off immediately, and it will be automatically powered on in less than two seconds. And so on and so forth.

In this case, you can remove the memory, graphics card, hard disk, network card, optical drive one by one, and then plug them one by one and try to eliminate them after powering on.

4.I had a fan wiring miswired yesterday, hehe.

5.As you said, it is impossible to generate a large amount of heat, and it is impossible to turn on the machine to this extent.

May you find the reason.

Is it that the 6 wires of the chassis are not knotted, this is a bit complicated, each motherboard is not exactly the same, you take a closer look at the motherboard manual.

Unplug all these 6 cables first and try to turn it on?

1. It may be that the power supply is insufficient. We are not a discrete graphics card.

2. It is possible that the sponsorship is broken.

Especially our new computer. If there is a problem, we will solve it as soon as possible, and do not delay.

Do you have a diagnostic card?

I guess it's a short circuit, so I pulled all the jumpers and tried it.

If the cause of the short circuit is ruled out by the minimum system method, then it is hardware incompatibility.

Hopefully, it's not a problem with the reboot button interface on your case, you try to unplug the reboot button cable on the chassis first.

Your case power supply voltage is not enough It is recommended that you change the case power supply.

Did you forget to add silicone grease to the CPU heat sink! The phenomenon is too similar to CPU overtemperature protection.

Unplug the switch cable from the motherboard, use a screwdriver to short-circuit the switch, and see if it still restarts? It could be that the chassis switch is broken.

The voltage of the power supply does not meet the rated voltage of the machine!!

Probably a problem with the power supply.

You should see if the hardware is compatible.

Unplug the cord from the restart button and try it

It's very easy to install the computer system, just read it!

Turn on the computer, insert the USB drive with the program into the computer, and follow the prompts to load the program.

It is recommended to buy a disc and install it yourself. **There are a lot of them, and there are also some sold on the U disk, and the seller will help you get it, and buying it back is basically the next step. **It's only a few dozen yuan. Hope to adopt.

Light up first, connect the display screen to turn on after all are installed, if there is no abnormal sound and abnormal display, it will be lit successfully. At this time, put the system disk in, select the optical drive to start in the BIOS settings in the monitor, and start the USB disk if it is a USB flash drive. Then restart your computer.

The computer will automatically restart and install automatically, so you don't have to worry about it. After installation, restart,Press F12 on the keyboard to enter the BIOS settings,If you don't know how to set it, don't set it,There will be no problem,People will set it to be able to raise the computer performance to the best。 Finally, select the system tool on the system disk - partition, and divide it into regions, and you're done.

You buy the system disk on **, the girls are making a lot of trouble, we don't have to worry about the system installation.

Get a USB flash drive to start, and then go to the USB flash drive to make the system, simple.

Install the system wherever it is assembled.

The socket of computer accessories has an anti-reverse plug design, for example, if the memory module is plugged in backwards, it cannot be plugged in. Accessories can not be plugged in, to see the installation instructions, accessories are manual. Only a few signal cables on the front panel are not anti-reverse, you can go to the Internet to find relevant information.

If you are a novice computer, you should not assemble the computer by yourself, and accessories such as the power supply and motherboard may burn out.

The real novice will plug the AMD CPU into the motherboard of the Intel series or the Intel CPU into the motherboard of the AMD series, and the two cannot be installed at all, and the power supply is too small to install the graphics card CPU**, and the memory module cannot be pressed tightly.

You don't need to worry about this, the jacks of the line are divided into positive and negative, if you plug it in backwards, you can't plug it in, don't plug it hard at this time! It should be noted that the jumper of the motherboard to connect the power supply and restart button is marked on the motherboard.

The cable of the computer generally has a foolproof design Don't force the cable that can't be plugged in, take a closer look at whether it's plugged in backwards Novices are easy to install bad is the CPU socket of the motherboard, especially Intel's memory is bought wrong or plugged in the wrong way, then it can't be plugged in at all If the CPU is installed without silicone grease and directly put the radiator, the CPU will overheat Install the graphics card, these PCI-E accessories may be installed incorrectly, which may damage the card slot of the graphics card or the motherboard card slot If the fan is installed casually, it may lead to confusion in the air duct, and the computer will overheat.

The most erroneous place to install yourself is the CPU. Others, fortunately, if plugged incorrectly, it won't burn, at most, it won't turn on or run.

Generally, there are no consequences, and then re-comb the installation process to see if there is a wrong step.

There are error-proof settings, and you can't plug in if you don't plug it incorrectly.

The one that can't be assembled can not be turned on in minutes!

The first thing to know is what this computer is for? What is the budget? Depending on the use and budget, you will know what kind of accessories can meet the above requirements.

In addition, the motherboard determines the processor interface, memory interface, and SSD interface, and it cannot be installed if it does not match. Processors, memory, graphics cards, and SSDs have the biggest impact on your computer's performance, while the motherboard and power supply have a big impact on your computer's stability.

If you don't overclock and don't connect the wrong wire, you won't burn the accessories.

The big problem is burning out a certain part.

Minor issues have a non-compatibility with a part.

It doesn't burn out, but novices are generally prone to problems.

1. The CPU is installed incorrectly, this is very fatal, it is installed in reverse, and it will be scrapped as soon as it is pressed.

2. Motherboard power jumper, mainly a variety of indicators and boot jumpers, etc., this should be noted, be sure to come to the manual, according to the positive and negative poles of the manual to connect (the jumper is mainly 4 groups of 2 pieces), otherwise it will not be turned on.

Nothing else.,As long as you connect all the power supplies.,Basically, it won't be overloaded.,Only the power supply is insufficient and can't turn on the machine.,In addition,Xiaobai is not recommended to install it by itself.,Or spend 1-200 to ask someone to assemble the system by the way.。

To build a computer for beginners, the first thing to see is whether your basic knowledge is enough

1. Do you understand the matching of the motherboard slot and the processor, do you understand the difference between the DDR3 and DDR4 memory supported by the motherboard, and the hard disk model supported by the motherboard, here is mainly the hardware problem supported by various slots on the motherboard.

2. The problem of power supply, the power cannot reach the total power consumption of the host, which will also cause the computer to run unstable.

3. The size of the chassis can't fit your motherboard or discrete graphics card.

4. The second is the problem of matching the same level of each hardware, the processor is selected very well, but the memory is selected with a relatively low frequency, just like this unreasonable collocation causes the overall performance to not be fully utilized.

As for what you said, burn out the motherboard, as long as you are not buying junk unbranded hardware, generally not.