What should I do if the black floor tiles become flowery?

First of all, we have to see what seeps in, if it is rust, then it is necessary to wash it with 100:1 dilute hydrochloric acid or oxalic acid, if it is oil or dust and other stains, you can use dish soap, all-purpose water, etc. to clean, if you want to remove the scratch, the difficulty is very high, it is recommended not to do any grinding attempt, because it is definitely worth the loss, after the scratch is cleaned, polish and polish with special polishing wax for stone, and try to reduce this trace.

If your bricks have been used for more than three months, don't try to knock them out and replace them again, because after a long time, the variety you buy may not be in stock, and each batch of bricks has a certain color difference, even if it is changed, it is not colored. Hello, many people are not very clear about how to maintain the tile, resulting in the tile aging quickly, let me explain it to you.

1. Add a small amount of ammonia with soap to effectively polish the tiles.

2. Use a rag with a little linseed oil or hydrochloric acid to wipe off the muddy water on the tile.

3. After mixing the same amount of linseed oil and turpentine, it can not only wipe the stains on the tile, but also keep the tile with good gloss.

4. When there are slight scratches on the surface of the polished brick, you can use toothpaste to apply it around the scratches, wipe it repeatedly with a dry cloth, and then evenly apply the wax oil with a cloth and wipe it with a clean cloth to eliminate the scratches and achieve the effect of being as bright as new. Note: The ratio of wax oil preparation is:

Kerosene: Wax = 9:

The general cleaning method is as follows**:

Type of contamination. Cleanser.

Oil, grease, beer, wine.

Alkaline detergent.

Ink stains, coffee, juices.

Sodium hypochlorite diluted.

Rust stains, lime scales.

Hydrochloric acid or phosphoric acid solution.

Marker. Organic solvent.

Paint. Turpentine or ketone.

Soy sauce, vinegar. Acid or alkali release.

Daily cleaning. Dish soap, soapy water.

Summary. How to deal with the floor tiles.

1. If there are traces like scratches on the floor tiles, you can wipe the scratches clean with a wet wipe.

2. If the floor tiles are scraped severely, you can apply some toothpaste on them, and then wipe them vigorously with a cloth.

3. If it is just scratched, just brush the flower with paint similar to the color of the tile.

4. If the flower is more serious, it will affect the appearance effect, and the scratched tile needs to be replaced.

How to maintain tiles 1. Surface cleaning work.

If it is stained, it should be removed immediately, and it is best to choose the right cleaning agent according to the stain.

What should I do if the black floor tiles become flowery?

Hello, I have seen your question and am sorting out the answer, please wait a while.

How to deal with the floor tiles 1, such as cracks on the floor tiles and leave traces like scratches, then you can use a wet wipe to wipe the scratches clean. 2. If the floor tiles are scraped severely, you can apply some toothpaste on them, and then wipe them vigorously with a cloth. 3. If it is just scratched, just brush the flower with paint similar to the color of the tile.

4. If the flower is more serious, it will affect the appearance effect, and the scratched tile needs to be replaced. How to maintain tiles 1. If the surface cleaning work is stained, it should be removed immediately, and it is best to choose the appropriate cleaning agent according to the stains.

2. Gap treatment is generally early regret pin like the tile before the stuffiness of its gap is also easier to hide some dirt and bacteria, then it can be said that this place is also the most important place to clean, but also to pay special attention to a place, you can often use candles to smear it on this seam, it can be said that it also has the phenomenon of preventing stains. 3. Wear and tear repair: It is necessary to know that the surface of the ground tile is more prone to friction, land travel, stains, etc., and there may be uneven surface inside, so in order to make its surface better, the floor tile should be waxed regularly, which can also play a certain protective role, and the most important thing is to make the surface of the tile look more shiny, and at the same time prolong its use time.

I hope this time can be helpful to you, I wish you a happy life, give a thumbs up, thank you.

The welding joint on the tile is permanent, it is not the welding residue that sticks to the tile, but because the welding residue of the high temperature during welding has burned the smooth surface layer of the tile, causing actual damage to the brick surface. Welding slag is melted into the glaze of the tile surface at high temperature, and the welding slag will rust when exposed to water or moisture, and the tile will become yellow spots.

1.Oxalic acid, hydrochloric acid, and sulfuric acid can be used to corrode welding slag, which can be seen at the time, but it cannot be used.

2.For dense black spots of welding slag, you can put a single layer of toilet paper on it, because the black spots of welding slag protrude from the brick surface, and then pour the detergent after 1:1 mixing.

If the paper is covered with a layer of plastic wrap or film to prevent the liquid from volatilizing, it can be soaked for 1-10 hours to slowly decompose the black spots. The soaking time is based on the size of the black spots of the welding slag, some of them will decompose in more than 10 minutes, and the soaking will not affect the gloss and structure of the brick surface, but only the black spots of the welding slag.

3.The scattered black spots can be wiped on it with dry cotton, so that the cotton filament wraps the solder joint, and then sucked in with a needle and dripped on the black spot of the welding slag. After 30-50 minutes, the black spots are decomposed into yellow water, wipe off with a wet towel, if the black spots are serious, you can scrape them with a tool, and then soak them on to decompose them once.

4..If the burn is severe, you can find a professional master to grind it with a grinder to see if the color difference of the tile is serious, and the severity mainly depends on the type of material of the tile. Such as antique bricks, after polishing the surface layer will not be so obvious, and glazed bricks will be very different after grinding off, if it is glazed bricks are recommended to be replaced.

5.Replace the bricks with new ones, get rid of the burned bricks, and pay attention to the cement as well, otherwise it will fall off after using glue.

6.If you don't want to change the bricks just for aesthetic reasons, you can hang (or cover) related decorative items on the brick surface to cover them, such as picture frames.

When most families decorate the house, they will use ceramic tiles as ground decoration materials, because the tiles are not only durable, but also very convenient to clean, but after a period of use, many people will find that the tiles at home have turned black, so how to deal with the amount of tiles that have become black in 4 years? How to clean the tile floor? Let's take a look!

First, how to deal with the tiles that have become black in 4 years.

Squeeze the toothpaste in the blackened place of the tile, and then brush it with a toothbrush, so that the dirt in the surface and crevices of the tile can be cleaned up, in addition, you can also mix lemon, baking soda, white vinegar and water in a certain proportion, brush the blackened place after dipping it with a brush, and then wipe it clean with a dry rag, and the edible alkali dissolved in warm water also has the same effect.

Second, how to clean the tile floor.

1. After a period of use of the tile, the gap between the tiles needs to be cleaned Xunchun, after cleaning, you can use a brush to paint a layer of waterproofing agent in the gap of the tile, which can play a role in preventing the growth of mold, and when cleaning the tile floor daily, you can use soap, dish soap, etc., so that the tile can be cleaned more cleanly.

2. If you accidentally spill ice cream, beer or tea on the tile floor, you should immediately use potassium bicarbonate or sodium hydroxide solution to clean it, if the tile surface is accidentally stained with cement or ink, it is recommended to use nitric acid or hydrochloric acid diluted solution for cleaning.

3. Wax the tile floor every other time, which can improve the gloss of the tile floor, and also extend the service life of the tile, but before waxing the tile floor, the tile floor must be thoroughly cleaned, and then the tile floor is evenly coated with wax, and the tile surface shall not be trampled within eight hours after waxing, otherwise there will be traces.

Summary: How to deal with the black tiles in 4 years is introduced here, in order to make the home environment look more clean and tidy, we must understand the cleaning and maintenance methods of the tile floor, so as to avoid damage to the tiles and cause unnecessary trouble. If you want to know more about decoration, you can pay attention to the relevant information of Qeeka Home.