Will it be expensive to have your own compartments and compartments in a loft style house?

It won't be very expensive The partition you first use a steel-wood or steel-concrete structure It's about 400 480 yuan per square meter, just go The next room is better to do We are professional construction design, you need to contact 1348833819

Advantages of concrete compartment: cast-in-place compartment refers to the method of directly planting reinforcement or slotting on the ring beam, load-bearing column and wall, and then directly molding with shell plate and pouring cement for partitioning. Its advantages are that it occupies relatively little space at the height of the floor, has good sound and heat insulation effects, and has no sense of shaking; The service life is the same as that of the main structure of the original house for 50 70 years, and the disadvantages are that the construction is complex, the maintenance time is long in the construction stage, the construction site is relatively dirty, and the load-bearing requirements are high.

Construction process: pay-off, shoveling the wall skin, drilling, hole cleaning, formwork erection and installation, glue matching, glue filling, reinforcement reinforcement, rebar production, Bangza, pouring concrete, concrete curing, dismantling formwork, completion and cleaning.

Floor maintenance and demoulding requirements:

1. The concrete strength of the span of more than 8 meters is 100%, and 75% of the concrete can be removed only after 8 meters and below 8 meters; Concrete strength when the floor can be on the person and construction. (Generally, the intensity can reach 24 hours after watering, and 7 9 days under normal maintenance in spring, summer and autumn; In winter, under normal maintenance for 10 to 15 days, the mold can be removed).

2. Under normal maintenance, it should not be less than 2 times a day; Make sure there is 11 to 16 minutes of water on the floor each time.

3. The moisturizing and curing of concrete is very important for the growth of its strength and the improvement of various properties, especially the early proper maintenance can avoid surface dehydration and greatly reduce the occurrence of expansion cracks in the initial stage of concrete. Therefore, the necessary maintenance after the floor concrete pouring (generally 24 hours) must be guaranteed, such as in the actual construction, due to the rush and watering will affect the elastic line and the construction personnel operation, the construction must adhere to the cover sack or straw bag for about a week of proper moisturizing maintenance.

Chongqing Gecheng cast-in-situ compartment.

Enter the area and get the decoration for free**].

Nowadays, many people buy a house with loft structure, the first thing they need to consider is the cast-in-place compartment, and many owners question whether the cast-in-place partition is dangerous. So, let's share with you is it dangerous to share the LOFT cast-in-place compartment? I hope it can be helpful to everyone.

1. Is the LOFT cast-in-place partition dangerousThe LOFT cast-in-place partition is not dangerous, and the planting reinforcement method should be used when fixing the corners, so that the main beam will not be damaged; Be sure to use ribbed steel bars, tie 2-4 layers, and the distance is about 130-180 mm; Choose high-quality cement brands and sand with a ratio of 2:4:6, and then mix well; After the construction of the partition floor slab is completed, it needs to be maintained, as long as the materials are qualified and the construction quality is reliable, there is no danger.

Second, the necessary conditions of the cast-in-place partition 1, the height of the house must be met, and the lower edge of the duplex floor slab and the lower edge of the original floor slab are the best at the same level. The lower edge of the attic floor slab shall not be lower than 2.6 meters, and the height of the attic floor slab and roof shall not be less than 2.4 meters, and the minimum shall not be lower than 2.2 meters. 2. The span at both ends of the attic should not be too large, and the beams and columns need to be designed to support it when it is too large.

In the case of channel steel construction, it cannot exceed four meters, and the maximum cannot exceed six meters. 3. Steel structure partition and cast-in-place concrete partition, which compartment method is more suitable for loft 1. The steel and wood structure partition is welded into a steel mesh using section steel, and the wooden board is laid on the top and gypsum board is used below. The load-bearing mainly depends on the welding quality of the section steel and the anti-bay ability of the main beam, and the most important thing is the family shelter connection method of the steel structure and the wall.

Advantages: convenient construction, short construction time, no impact on other decoration projects, clean and tidy construction site. Cons:

**High, the foot feeling is not good, giving people a feeling of emptiness, sound insulation, shock resistance, corrosion resistance is relatively poor, and the thickness of the compartment is large. Second, the cast-in-place steel Zhaoye reinforcement concrete partition according to the location of the site design, formwork, reinforcement, pouring concrete, after a period of maintenance, the template is removed, and then the floor slab is formed. The construction steps are simple, very strong and firm, only the construction quality and materials are not problematic, and there are no potential safety hazards.

Article summary: The above is the relevant content of the LOFT cast-in-place compartment is dangerous to share with you, I hope it will be helpful to you. It is recommended that you find a regular and professional construction team, and do not bring potential safety hazards to yourself in order to save money.

Because the house needs to be lived in for a lifetime, it can't be sloppy at all.

Do the math how much it will cost you to renovate your home

The normal manufacturing method of the loft compartment:

1: Steel beam + tread steel plate scheme, using steel beam as a bending component, slightly expensive burial, the total thickness is about 280mm.

2: Steel beam + cement fiber board scheme, high cost, cement pressure plate as a brittle material used in the floor slab is risky (not allowed by the Zhuyu Bizhai specification), the completion thickness is about 160mm

3: TD-LOFT ultra-thin sandwich scheme, using corrugated steel plate as a stressed member, has waterproof, fireproof, sound insulation and other functions, low cost, the total thickness is about 125mm after completion

There are three ways to loft compartments, the height of the layer is more reasonable to distribute the lower meter, and the upper meter is more appropriate.

The three methods are:

1. Timber structure support method.

The advantages and disadvantages of this method are obvious. The advantage is that the construction period is short and the cost is low. The disadvantages are:

The firmness is relatively poor, the waterproofness is poor, the vibration is very large, even if the soundproof cotton is laid between the bracket board and the floor, the sound insulation effect is still very poor, there is almost no privacy upstairs and downstairs, and there is no fireproof, so in the process of doing it, the wood must be fireproofed.

2. Steel frame structure.

This method is more common because the construction period is shorter and the ** is also moderate. The construction difficulty is medium, but the disadvantages are also more obvious: the vibration is large, the waterproof and sound insulation is poor, and the thickness of the partition is large, and the ceiling is about 20cm-30cm.

This method is first of all to use the channel steel as the main support, every 50-80 cm, and then weld it with a triangle steel at intervals of 50-80 cm, and the welding point is best to repeat the anti-rust paint 3 times.

3. Concrete cast-in-place partition.

Concrete cast-in-situ partition is generally used to lay steel bars, the main reinforcement is 14mm, the auxiliary reinforcement is 10mm, the laying interval is about 15 cm, and the cement should be 425 strength, and the ratio of C25 or C30 high-strength concrete. According to the operation method, cast-in-situ can be divided into three subcategories, one is the section wall welding method, the other is the planting reinforcement welding method, and the third is the chemical bolt method.

There are basically three types of loft compartments:

Steel-concrete structure: The weight of the steel structure itself is heavier, with a thickness of about 10cm

steel-timber structures; The weight of the body is light; The thickness is about 15 20cm all-steel structure: its own weight is light; The thickness is about 10cm

The more reasonable distribution of floor height meters is:

The height of the lower compartment is about one meter, and the height above the compartment is about one meter.

Such a high distribution is more reasonable, and people will not have a depressed and uncomfortable feeling when living in the house.

There are basically three types of attic making.

The first, steel and wood structure, with a thickness of about 15 20cm;

the second, steel-concrete structure, with a thickness of about 10cm;

The third type, all-steel structure (this structure is generally used for store goods storage, shelves, indoor home rarely used).

The height of the floor is more reasonably distributed to the lower meter, and the upper meter is about the same.

Compared with traditional materials, the main advantages of loft high-strength cement floor slabs are:

High density and high strength, bearing 3 tons per square meter;

It is lighter than the weight of the rammed floor slab, which reduces the load of the building;

The thickness is thin, generally 1200 2400 25mm to save space;

Fireproof and waterproof, it is a new type of floor material that is Class A non-combustible;

Low thermal conductivity, good thermal insulation effect;

The sound insulation effect is particularly good;

The construction is simple and fast, the comprehensive cost is low, the construction waste is less, and the service life is generally more than 50 years.

There are roughly three types of loft compartments from the production:

1. Steel and wood structure, with a thickness of about 15 20cm

Advantages: fast construction, light weight, small wall stress; Disadvantages: easy to deform, not soundproofed).

2. Steel-concrete structure, with a thickness of about 10cm

Advantages: good sound insulation effect, not easy to deform, can be used as a bathroom in the attic, good waterproof effect; Disadvantages: self-weight, large force on the wall, slow construction.

3. All-steel structure.

This structure is generally used for store goods storage, shelves, and is rarely used in indoor homes.

The height of the floor is more reasonably distributed to the lower meter, and the upper meter is about the same. In this way, people will not have a feeling of depression in the house.

There are three main types of attic making.

1.Steel and wood structure, thickness of about 15 20cm (advantages: fast construction, light weight, low wall stress; Disadvantages: easy to deform, not soundproofed).

2.Steel-concrete structure, thickness of about 10cm (advantages of this structure: good sound insulation effect, not easy to deform, can be used as a toilet in the attic, good waterproof effect; Disadvantages: self-weight, large force on the wall, slow construction.

All-steel structure (this structure is generally used for store goods storage, shelves, and is rarely used for indoor furniture).

The height of the floor is more reasonably distributed to the lower meter, and the upper meter is about the same. In this way, people will not have a feeling of depression in the house.

Loft literally means warehouse, attic, but by the time the word became fashionable and evolved into a fashionable lifestyle in the late twentieth century, the word went far beyond its original meaning.

In the 40s of the 20th century, the loft lifestyle first appeared in New York, USA. Factories or warehouses are renovated into studios and living rooms. This style of decoration originated in Europe and the United States, known as loft, is quietly emerging in Guangzhou, Shanghai, Beijing and other places, and is respected as a kind of "home" fashion.

Lofter, the term for loft enthusiasts, refers to ordinary loft enthusiasts, who are usually interested in loft-style architecture, especially home furnishings, out of curiosity or other reasons. They love this fresh way of life and are willing to try it. The lofter is usually a group of fashion-conscious young people who experience the unique charm of loft and find the heartbreak utopia they yearn for.

In addition, NetEase has launched a new web product called Lofter. The product is named Lofter, and the word Lofter is an extension of Loft. Loft means "a wide and open free space", and the people who focus on their interests and share their creations in this space are naturally lofters.

Different from the heaviness of blogs and the complexity of microblogs, LOFTER aims to provide users with a comfortable, quiet and exquisite recording tool and creation platform! That is, it takes the meaning of "love to record life, pursue fashion quality, and advocate free space", and uses a com independent domain name named "lofter", and the overall product concept is eye-catching.

Now there should be no meter-high residential loft, and the code requires that the height of the meter-high ceiling cannot be exceeded, and only some commercial projects can do it. The reasonable distribution of the height of the layer is about meters: the height below the compartment is about meters, and the height above the compartment is about meters.

The normal manufacturing method of the loft compartment:

1: Steel beam + pattern steel plate scheme, using steel beam as a stressed member, slightly expensive, the total thickness is about 280mm.

2: Steel beam + cement fiber board scheme, high cost, cement pressure plate as a brittle material used in the floor slab is risky (not allowed by residential specifications), the thickness of the completion is about 160mm

3: TD-Loft interlayer, using corrugated steel plate as a stressed member, has waterproof, fireproof, sound insulation and other functions, low cost, the total thickness is about 125mm after completion

There are basically three types of attic making.

Steel and wood structure, thickness of about 15 20cm (the advantages of this structure: fast construction speed, light weight of the attic, wall force is not large; Disadvantages: deformation, no sound insulation)

Steel-concrete structure, thickness of about 10cm (the advantages of this structure: sound insulation is not easy to deform, the attic can be used as a bathroom, and the waterproof effect is good; Disadvantages: heavier self-weight, greater force on the wall, longer construction time).

All-steel structure (this structure is generally used for store goods storage, shelves, indoor home rarely used) floor height meters are more reasonably distributed to the lower meters, the upper meters or so. In this way, people will not have a feeling of depression in the house. If you are satisfied, please adopt.