How to disassemble the lampshade and how to remove the lampshade

1. Round ceiling lampshade

Before disassembly, you need to cut off the power switch of the light. Only after the power is off can the disassembly safety be guaranteed.

Since round ceiling lamps are usually opened by rotating the shade, a screwdriver is required.

Slowly remove the small screws around the iron ring of the lampshade. When the lampshade is loose and can be turned, turn the lampshade again until it is unscrewed, and finally the lampshade can be removed. That's it.

2. Recessed ceiling lamp

Since this lamp is installed directly in the integrated suspended ceiling.

up, it seems that there is nowhere to start. In fact, it is not difficult to remove the lampshade of this lamp.

Recessed ceiling lights are stuck in the ceiling.

Above. Before removing the lampshade, you need to cut off the power supply first, then remove the ceiling gusset, and then look carefully, you will find that the embedded ceiling lamp is blocked by a spring clip. Yes, cut it off.

3. Aluminum gusset ceiling lamp

For this type of fixture, it is not possible to remove the lampshade by rotating it directly. The correct thing to do is to cut off the power supply first, and then use a small screwdriver or small blade to tilt a corner from the seam of the aluminum gusset, remove the gusset around the lamp, and you can see that there are two lights on the ceiling. Similar to downlights.

Buckle of snap buckle.

Then use two stiffer plastic cards, insert them along the corners of the gusset, move the card to the other end, pry it off with a little force, and finally pull out the gusset by hand and remove the lampshade.

4. Rectangular ceiling lamp

Compared to round lights, this type of light is more cumbersome to disassemble. First, you need to cut off the power and then locate the four corners around the light.

After that, you can borrow the dishwashing hook of the suction cup, suction the aluminum part on the side, and slowly pull down, pulling each corner until the lampshade is removed. In the process of pulling, the action should be slow and not too forceful, so as not to directly damage the lamp or re-work.

Different types of lamps and lanterns have different methods of disassembling lampshades.

1. Round ceiling lampshade

Before dismantling, the power switch of the lamp needs to be cut off, and only after the power supply is cut off, can the disassembly safety be guaranteed. Because the round ceiling lamp is usually opened by rotating the lampshade, it is necessary to slowly remove the small screws around the iron ring of the lampshade with the help of a screwdriver, and when the lampshade is loose and can be rotated, the lampshade can be rotated until it is unscrewed, and finally the lampshade can be removed.

2. Recessed ceiling lamp

Since these luminaires are mounted directly with the integrated ceiling and seem to have nowhere to start when dismantling, the lampshade of such luminaires is actually not difficult to remove. The recessed ceiling lamp is stuck in the ceiling, before taking the lampshade, the same needs to cut off the power supply first, and then remove the ceiling gusset, and then observe carefully, you will find that the recessed ceiling lamp has a spring clip to jam it, and it can be broken off.

3. Aluminum gusset ceiling lamp

For such luminaires, it is not possible to remove the lampshade if it is rotated directly. The correct way should be to cut off the power supply first, and then use a small screwdriver or a small thin blade to warp a corner from the seam edge of the aluminum gusset, and remove any gusset around the lamp, and you can see that there are two spring buckles similar to downlight buckles on the ceiling lamp. Then use two harder plastic cards, insert them into the corners of the extension plate, move the card to the other end, pry down a little bit of the gap with a little force, and finally pull out the gusset by hand and remove the lampshade.

4. Rectangular ceiling lamp

Compared to round luminaires, this type of luminaire will be more cumbersome to disassemble. First of all, you need to cut off the power supply, and then find the four corners around the lamp, you can borrow the washing hook of the suction glass disc, suck it on the aluminum alloy part on the side, and slowly pull down, pulling at each corner until the lampshade is removed. In the process of pulling, the action should be slow and not too forceful, so as not to directly damage the lamp or exert force again.

The method of disassembling the lampshade as soon as you learn it.

1. Turn off the power of the ceiling light.

2. Use the blade to reach between the gap between the ceiling lamp shade and the lamp plate, and pry it open.

3. After prying it open, slowly break the lamp tray along the lampshade with your hand to make it fall off the ceiling.

4. Hold the lampshade with your hand and take it off safely.

Ceiling lamps have different shapes, the common ones are often two-week, square and round, and the two of them are different due to their different shapes.

The round lampshade is generally held by holding the lampshade with one hand and rotating it counterclockwise with the other hand, and the lampshade can be easily removed.

The square lampshade will have a buckle on each of its four opposite corners, which can be removed by breaking the buckle.

Of course, there is also a turn-buckle type, which is different from the buckle that needs to be broken, it is to turn the buckle so that the buckle hook no longer hooks the base, and the lampshade will be taken off.

The last one is the screwdriver, use a screwdriver to unscrew the screws separately, and the lampshade will naturally be removed.

The four common ways to disassemble the lampshade are on the top, I hope it can help you, here Sunshine wants to remind everyone that you still have to be careful when climbing the ladder, safety first!

With the development of industrial technology, ceiling fan lamps have gradually developed from the monotonous shape and single function of the past to multi-functional family lamps and lanterns, how to install them correctly? Let's find out today.

1.First of all, fix the hanger on the ceiling, and install the screws that fix the hanger according to their own ceiling material, and choose the screws that can fix the hanger, which must be able to withstand 16 kg of tension.

2.Put the wave cup on the boom, the power cord of the motor is drawn out from the inner hole of the boom, and then put the end of the boom with two holes into the head of the motor, insert the connecting bolt, lock the safety slightly, and tighten the fixing screw.

3.Hang the installed motor to the hanger, pay attention to the hanger on the boom has a slot, this slot should be stuck into the bump of the hanger. Then connect the power cord, and the wiring method should be wired according to the requirements of different ceiling fans.

4.Align the 3 small holes on the fan blade with the 3 small holes of the leaf fork, and lock the 3 screws on the fan blade in a uniform order for all the fan blades to avoid the angle deviation of the fan blades and cause the ceiling fan to shake when rotating.

5.Fix the assembled fan blades to the motor separately and tighten the set screws. Then gently turn the motor with your hand to see if the motor is flexible when rotating, and confirm that the fan blades do not collide with any objects.

Finally, check the parallelism of the fan blades, all the high sides of the fan blades on the ceiling fan should be the same high, and the low side should be the same low.

Otherwise, the ceiling fan will wobble when it turns.

6.Connect the combined power cord of the lamp stand to the empty power cord in the motor switch box, and then connect the lamp stand with the switch box and tighten it with screws. Then unscrew out the lamp head ring, put on the lampshade, lock the lampshade with the lamp head ring, preferably with the light source, and screw it tightly.

7.After the installation is completed, you should check that all the screws on the ceiling fan are tightened, and then turn on the power to test whether the ceiling fan is working properly. Try to rotate for about 10 minutes, and check again whether all the screws or screw rings on the ceiling fan are loose.

Ceiling fans should be inspected at least once a month when they are in normal operation. Summer is here, and ceiling fan lights can both blow wind and illuminate.

It is really practical, the installation of chandeliers at home should be noted according to the height of the room, compared with other lighting fixtures, ceiling fan lamps need to rotate constantly during the work process, and the safety requirements are higher, so we must ask professionals to install and operate when installing. The lamp master platform provides door-to-door installation of lamps and lanterns for lamp users across the country.

Cleaning, maintenance, renovation and other services, senior masters, professional operation, if you need, find a lamp master will be able to help you solve all the problems.

Generally speaking, it is fixed by the following methods, one is to tighten the lampshade (on the side) with four screws, and the other is to screw it up, and when removing it, rotate the lampshade in the counterclockwise direction, and the lampshade can be laid down. The third is the circlip type (less used, more used for small mouth lampshades), directly pulled down.

The other is directly rotated, which can be rotated in the opposite direction of the clock.

Hello dear, I'm really sorry, we can't hear the voice here, oh dear.

Summary. Different styles of chandelier lampshades are disassembled in different ways: first, round chandeliers, first turn off the power, use a screwdriver to remove the three screws around the iron ring of the lampshade, and then rotate the lampshade; 2. For rectangular chandeliers, use the suction cup hook of the suction glass disc to suck it at the aluminum alloy and slowly remove the lampshade; 3. Embedded chandelier, find the spring clip and disassemble it; Fourth, the aluminum gusset chandelier, use a screwdriver to warp the lampshade from the seam of the aluminum gusset.

Hello, I am your full-time answerer today, and I am happy to answer for you Different styles of chandelier lampshades have different disassembly methods: 1. For circular chandeliers, turn off the power first, remove the three screws around the iron ring of the lampshade with a screwdriver, and then rotate the lampshade; Two slag cavity rock, rectangular chandelier, with the suction cup hook of the suction glass plate, suck the round eggplant in the aluminum alloy, slowly remove the lampshade like a royal; 3. Embedded chandelier, find the spring clip and disassemble it; Fourth, the aluminum gusset chandelier, use a screwdriver to warp the lampshade from the seam of the aluminum gusset.

The above is the answer given. You can refer to it, I hope it will help you. If you are satisfied with my service, I hope you can praise my service and sales. I wish you a happy life and all the best. 

Summary. Hello dear The lampshade of the ceiling fan lamp can be removed.

Hello dear The lampshade of the ceiling fan lamp can be removed.

Methods and steps for disassembling the ceiling fan shed with lampshade: 1: first find a ladder with the word "person", and climb it up:

Use a " " screwdriver to loosen 4 small "" screws in a counterclockwise direction. (at the bottom of the chain bridge tremor cover) you can remove the lower ceiling fan shade. Two:

There is another kind of lampshade that is directly screwed up, and the ceiling fan shade with lampshade can be loosened and removed in the counterclockwise direction.

Or there are two ways to fix the general lamp and the cover of the hall: one is to use 3 or 4 small screws to clamp around the bottom of the lampshade, which can loosen the screws, and the other is directly screwed up, which can be unscrewed in the direction of the counterclock.

The main functions of the lampshade are: 1. Blocking strong light. Avoid direct exposure of light to the human eye, which can cause dizziness.

2. Protection. It can prevent the chain and invasion of dust and oil smoke, so as to prolong the service life of the bulb. 3. Decorative function.

The color of the lampshade and the good matching of the styling shed can also become a scene in the room, giving people enjoyment. The choice of lampshade mainly depends on personal hobbies and the conditions of the room.

Hello oh kiss The method of disassembling the lampshade is as follows: The steps are as follows: 1. Cut off the power 2. Take out the lampshade.

This kind of lampshade should start from its four corners, use the dishwashing hook of the glass suction cup, suck the aluminum alloy part on the edge, slowly pull down, pull all the four corners, until the lampshade is removed 3, remove the bulb 4, the second method introduces the disassembly method of the aluminum gusset ceiling lamp: first cut off the power supply, then use a small screwdriver or a small thin blade to tilt a corner from the edge of the seam of the aluminum gusset, remove the lampshade 5, pull down a small piece of aluminum gusset with the same method, and then take out the bulb. The way to remove the recessed ceiling light is to first cut off the power supply, then find the spring clip and disconnect it.

The method of dismantling the crystal ceiling light is to remove all the accessories first, then the tube, and finally the ceiling panel. And take out the lampshade, take out the lampshade. This shade starts at its four corners.

Use the disc hook of the glass suction cup to suck the aluminum alloy part on the side and slowly pull it down.

1.Start by preparing the ladder and removal tools, then turn off the power to ensure safety.

2.By holding the shade with one hand and rotating it counterclockwise with the other, the shade can be easily removed.

3.If the round shape is also a turnbuckle, different from the buckle that needs to be broken, it is to turn the buckle lightly so that the buckle hook no longer hooks the base, and the lampshade can be removed.

4.If it is a screwdriver, use a screwdriver to unscrew the screws separately, and the lampshade can naturally be removed.

5.The common way to disassemble the round lampshade is on the top, I hope to you, here to remind everyone, you still have to be careful when climbing the ladder, safety first!

When the LED light does not light up most of the reason is due to the LED light is broken, this time it needs to be replaced, so how to replace the LED light, and how to remove the LED lampshade? Let's take a closer look.

How to remove the LED lampshade.

There are three ways to remove the LED lampshade, which are as follows:

1. Remove the lampshade first, remove the fixed screws, or stabilize the lampshade with your hands all the time, so as not to break the lampshade if it falls, and then slowly rotate the lampshade in the counterclockwise direction, so that it can be removed.

2. Grab the frame of the ceiling lamp first and pull it down, you will see the spring inside, and then press the spring in the direction of the ceiling, but also grasp the strength, so that you can take off the ceiling lamp.

3. Try to remove the square gusset next to the ceiling lamp, this can be removed, because it is fixed by the card; Prepare a suction cup hook that can suck glass, suck it on the aluminum alloy part of the edge, and slowly pull down the four corners to pull it in a loop, and you can remove the ceiling lamp.

The LED lampshade has been removed, and the following is the replacement of the LED lamp, so how to replace the LED lamp? Take a look at the detailed steps below:

1. Turn off the switch first, with the help of a folding ladder, remove the shell of the LED ceiling light, and check whether the lamp is black and dark, if there is, it is likely that the lamp has been damaged. It must be replaced.

2. Secondly, if the lamp is still in good condition, you should try to tighten the position of the lamp joint to see if there is poor contact, which is relatively simple to operate, but it is also relatively easy to occur.

3. If the above problems do not occur, you can check whether the ballast is in good condition, whether there is a burning smell, and whether the appearance of the ballast is black and scorched.

4. Finally, check whether the contact head of the LED light has electricity, if not, it should be a problem with the switch or line.