How to turn on the Changan CS35 speed sensing locking function

To turn on the Changan CS35 speed sensing lock function, you need to start the engine and turn on the power supply of the whole car; The specific steps to turn on the Changan CS35 speed sensor locking function are as follows:

1. Open the door on the side of the Changan CS35 cab.

2. Press the brake pedal of Changan CS35 to prepare to start the engine.

3. Twist the key of Changan CS35 and start the engine.

Fourth, the instrument of Changan CS35 lights up, and the power supply of the whole car is turned on.

5. Press the speed sensing lock button of Changan CS35.

6. When the speed reaches 20 miles, the speed sensing lock function will be automatically turned on.

Speed-sensing auto-lock.

When the speed is higher than 20 km/h, all doors are automatically locked.

It should be noted that:

The speed-sensing auto-lock function is factory set to off and can be turned on in "incall-vehicle settings".

This does not need to be turned on, it is automatic by the system, I hope mine is helpful to you, I wish you a happy car.

I picked up a Changan CS35 speed sensor automatic locking function that didn't work.

This is automatically turned on and does not need to be manual. Hope mine can help you.

Go to the after-sales service to turn on the automatic unlocking function.

Go to the car where you buy to activate this feature.

The manual says that the speed of the car is 20 kilometers and it is automatically locked, but my car has been locked for a year, but it has not been locked, what is going on?

Summary. Three reasons for the failure of the car remote control lock Reason 1: In general, the failure of the car remote control lock may be the cause of the car body or the remote control key itself.

In the remote control key, the failure of the time control module, the aging of the antenna of the car remote control transmitter and the like may cause the remote control to work, which requires the owner to go to the 4S shop or the professional maintenance office in time to check and find out the problem when the remote control key fails, determine whether it is a mechanical problem. Reason 2: Due to the cold weather, some of the grease in the remote control becomes viscous, resulting in good contact, and the car remote control lock fails.

Therefore, the car owner should keep the car remote control key properly to prevent oil from entering. Reason 3: There is also a possibility that there is strong magnetic field signal interference around the parking of the car.

Because smart keys use low-intensity radio waves, they may not work properly in the presence of magnetic field interference. It is possible for criminals to hide around the vehicle and use signal jamming devices to interfere with the normal use of the remote control key, and steal valuables or vehicles in the car. Once the car remote lock fails, it is best to go to a repair shop.

Changan CS35 remote control can't open the lock.

Is it a problem with the remote control to receive the antenna.

Three reasons for the failure of the car remote control lock Reason 1: In general, the failure of the car remote control lock may be the cause of the car body or the remote control key itself. In the remote control key, the failure of the time control module, the aging of the antenna of the car remote control transmitter and the like may cause the remote control to work, which requires the owner to go to the 4S shop or the professional maintenance office in time to check and find out the problem when the remote control key fails, determine whether it is a mechanical problem.

Reason 2: Due to the cold weather, some of the grease in the remote control becomes viscous, resulting in good contact, and the car remote control lock fails. Therefore, the car owner should keep the car remote control key properly to prevent oil from entering.

Reason 3: There is also a possibility that there is strong magnetic field signal interference around the parking of the car. Because smart keys use low-intensity radio waves, they may not work properly in the presence of magnetic field interference.

It is possible for criminals to hide around the vehicle and use signal jamming devices to interfere with the normal use of the remote control key, and steal valuables or vehicles in the car. Once the car remote lock fails, it is best to go to a repair shop.

Hello! Dear, the question of your consultation, here is the answer to you as follows: the reason for the failure of the car remote control key:

1. The battery is out of power or the battery is in poor contact. 2. The time control module in the remote control key is out of order. 3. The antenna of the remote control transmitter on the car is aging, etc.

4. The front windshield of the car is pasted with an explosion-proof solar film, which shields the remote control signal to a certain extent. In the process of use, the smart remote control key should try to avoid contact with some strong magnetic fields, for example, where there are high-voltage lines or transmission towers, try to avoid vehicle parking. In addition, try not to throw it away when using the smart key, which may cause poor contact of the internal battery.

Normally, these are the causes.

1.The alarm is too sensitive, so if there is a little wind and grass around the car, it will keep ringing, and this situation can be adjusted.

2.If the door knock switch fails, the alarm will also sound. You need to go to a repair point for repairs.

3.The anti-theft sensor is too sensitive, but this is this adjustment in the immobilizer vibration sensor.

There is a sensitivity adjustment torque, and you can fine-tune it.

How car alarms work:

When you knock or shake the sensor to make the sensor vibrate, the ball rolls in the cylinder chamber. When it rolls away from a smaller secondary electrical contact element, the circuit formed by this secondary electrical contact element and the ** electrical contact element is disconnected. At this point, the switch will turn on, indicating that the controller ball has been displaced.

As the ball continues to roll past other secondary electrical contact elements, the circuit closes and disconnects until the ball finally stops rolling.

If the vibration of the sensor intensifies, the ball rolls longer and passes through more secondary electrical contact elements before it stops rolling. If this happens, the controller will receive a short-time pulse current from all the individual circuits. The controller can measure the intensity of the vibration based on the amount and duration of the pulse received.

If the ball only rolls from one contact element to another, the controller may not trigger an alarm at all. If someone hits the car and causes a large displacement, the vehicle may sound an alarm signal: a horn sounds, or a headlight flashes.

If the ball rolls for a long distance, the controller will sound the alarm across the board.

It is basically composed of two metal contacts, with the longer elastic metal contact being placed on top of the other metal contact. You can easily set these contacts to a simple switch: when they touch each other, current passes through.

When the car shakes violently, the elastic metal contacts also shake and come into contact with the contacts underneath, creating a closed circuit temporarily.

To turn on the Changan CS35 speed sensing lock function, you need to start the engine and turn on the power supply of the whole car; The specific steps to turn on the Changan CS35 speed sensor locking function are as follows:

1. Open the door on the side of the Changan CS35 cab.

2. Press the brake pedal of Changan CS35 to prepare to start the engine.

3. Twist the key of Changan CS35 and start the engine.

Fourth, the instrument of Changan CS35 lights up, and the power supply of the whole car is turned on.

5. Press the speed sensing lock button of Changan CS35.

Sixth, when the speed of the vehicle reaches 20 miles, the speed induction lock function will automatically open the hand rental and demolition.

Changan CS35If you want to set up automatic locking, you can click on the central control main field regret page "Vehicle set upright", and after entering the setting page, there is a remote control mode of "all doors" or "driver's doors".After selection, the automatic locking function can be completed.

This is a security function, but also an anti-theft function, generally when the speed of the car reaches a certain speed will be automatically started, mainly to prevent the car in the process of driving, the door suddenly open, resulting in accidents.

The function of automatic locking function.

On the one hand, the automatic lock can be in the process of driving, such as with a child, for fear that the child will open the door and cause an accident. But on the other hand, when an accident occurs, the automatic lock function becomes a chicken rib function that hinders rescue, delaying escape or treatment.

Therefore, in some countries, most car series have canceled the function of automatic locking, but there are also some luxury models that are directly set to automatically unlock in the event of a collision, which is also to prevent the occupants of the car from being unable to escape in the first place after an accident.