How to clean your own floor heating pipes, how to clean floor heating pipes

The user can clean the filter at the front end of the water separator before use every year to ensure the cleanliness of the water pipe and prevent the pipe from clogging the specific methods are as follows:

First, close the inlet and return valves connecting the conduit, then open the filter, remove the filter and clean it.

Check whether the filter screen is damaged or blocked, if it is damaged, it should be replaced with a filter screen of the same specification and installed as it is;

In the process of starting water supply or use of the floor heating system, air may accumulate in the pipeline, which affects the heating effect, at this time, the air release valve of the water distributor and water collector can be opened to discharge the gas, and the method is the same as that of traditional heating;

It is strictly forbidden to place high-temperature heat sources near the water collector and on the ground where the floor heating pipes are laid to prevent damage to the pipeline system;

When the geothermal heating system is not used in winter, care should be taken to prevent the water separator parts from freezing and cracking or the water in the heating pipe from freezing.

Generally speaking, there are three kinds - chemical soaking, projectile cleaning, and pulsed wave physical cleaning. Among them, the pulse cleaning method is the most used for floor heating, which can clean the scale and impurities of the floor heating pipe and water separator at one time.

Floor heating cleaning is generally calculated by the square, according to the heating area of geothermal heat, now it is generally 5-15 yuan a square is more reasonable.

There is also a kind of calculation according to the circuit, a circuit is basically 50-150 yuan, now most of the cleaning unit door-to-door cleaning costs are basically like this, different companies ** way is different.

For example, in Hangzhou, for example, the cost of cleaning a house with a heating area of 80 square meters is about 300 to 700, depending on the charging mode of the floor heating cleaning company, the cleaning institutions are different, the cleaning methods are different, and the cleaning fees charged are not the same.

For specific conditions, please call us or make an appointment for cleaning.

How to clean the floor heating pipes:

Clean the floor heating pipe first close the water inlet valve and outlet valve, install a water pipe at the head of the return pipe, close all the water distribution valves, only one valve is open, open the water inlet valve and outlet valve of the heating, after flushing for a period of time, open the water distribution valve in turn, and then clean the other valves and pipes.

Precautions for using underfloor heating:

1. The first time you use it, you must adjust the water temperature, the normal water temperature is between 25 and 30 degrees, the temperature is too high to ensure that the floor heating pipe is well used, it is very easy to deform and crack the bridge rent, the water temperature of the access needs to continue to increase, but it will only rise 5 to 10 degrees each time, and it needs to wait for it to run for a week before it can rise.

2. Check whether there is water leakage, generally after the installation of round cheating floor heating will be accepted, to ensure that it can be put into use only after it is qualified, but it is easy to be artificially damaged in the later decoration, which affects his normal operation, so before the first use, it is necessary to test the various fittings in the pipeline to ensure that there is no leakage and dripping.

3. Set the temperature, if there is no one at home, there is no need to turn off the floor heating, otherwise it will take a long time to preheat when it is turned on again to reach the corresponding temperature, which will lead to a waste of energy, and the temperature in winter is very low, if the temperature in the pipe is too low, there will be the problem of freezing and cracking, so it is necessary to ensure that the indoor temperature is 13 to 15 degrees, so as to ensure that the temperature is returned quickly.

Summary. Hello! How to clean the floor heating pipe by yourself The method is as follows; 1. Close the water inlet and drainage valves of the floor heating first, and the valves of all branches.

Then use a tool to open the screw plug on the top of the return section, which usually overflows some water when unscrewed, so put an old towel underneath. 2. Find a plastic bottle, cut a rectangular hole with scissors, and put the hole on the screw plug. 3. Next, open one of the diverted valves, slowly unscrew the water inlet valve, and close the main return valve, at this time, the plug covered by the plastic bottle will begin to discharge sewage.

4. When the discharged sewage becomes clean water, it means that the water pipe of the floor heating has been cleaned, and the water distribution pipe can be closed, and then other water distribution pipes can be opened in turn for sewage discharge. 5. After all the branches are cleaned, screw the plug back, and finally open the main water inlet valve, return valve and all the valves of the branch, and the floor heating can be used normally.

Hello! How to clean the floor heating pipe by yourself The method is as follows; 1. Close the water inlet and drainage valves of the floor heating first, and the valves of all branches. Then use a tool to open the screw plug on the top of the return section, and some water will usually overflow when unscrewed, so at this time, an old towel should be dug under the stove.

2. Find a plastic bottle, cut a rectangular hole with scissors, and put this hole pants or put it on the screw plug. 3. Next, open one of the diverted valves, slowly unscrew the water inlet valve, and close the main return valve, at this time, the plug covered by the plastic bottle will begin to discharge sewage. 4. When the discharged sewage becomes clean water, it means that the water pipe of the floor heating has been cleaned, and the water distribution pipe can be closed, and then the other water pipes of the branch road can be opened in turn for sewage discharge.

5. After all the branches are cleaned, screw the plug back, and finally open the main water inlet valve, return valve and all the valves of the branch, and the floor heating can be used normally.

1. The first step is to close the water inlet and outlet valves in the home and separate the heating system from the water supply system. Generally, to close the valve, it is necessary to screw the valve to the direction perpendicular to the pipe box, and install a plug position to the return pipe. Tap.

2. Close the water distribution valve in turn in the second step of the first Qingjizi, keep one open, and then connect the hose to the faucet and lead to the sewer. When an inlet valve is opened, the hot water is drained and circulated, flushing out the dirt from the pipes until the water is clean. 3. The whole flushing process needs to be maintained for about 1 minute, and then the No. 1 pipeline is closed, the No. 2 pipeline is opened, and the other pipes are flushed in place in the same way in this order.

The steps to clean the underfloor heating pipes at home are as follows:

Materials: screwdrivers, scissors, plastic bottles.

Step 1: Close the water inlet and drain valves of the floor heating and all the valves of the branch first, and then use a screwdriver to open the screw plug on the return section.

Step 2: Find a plastic bottle, cut a rectangular hole with scissors, and put the hole on the screw plug.

Step 3: Open one of the diverted valves, slowly unscrew the inlet valve, and close the main return valve, and wait for the discharged sewage to turn into clean water.

Step 4: After all the shunts are cleaned, screw the plug back and finally open the main inlet valve, return valve and all the shunts.

Here's how to clean your floor heating pipes at home:

1. First of all, the valves of the water inlet and outlet should be closed, and the heating system of your home should be separated from the heating system of the whole area, so as to better operate later.

2. Install a faucet at the position of the plug of the return pipe. You can choose to install it yourself, or you can ask a plumber to do it.

3. Close the water distribution valve in turn, and then leave only one in the open state. The faucet installed at the back is connected to a section of hose that leads directly to the sewer in your home.

4. Open the water inlet valve for heating, and then open the valve of the faucet, the hot water will be discharged down, and the dirt will also be brought out by the water flow, so that it will have a cleaning effect.

5. After rinsing for a period of time, observe the quality of the water, and then follow the above methods to clean each pipe.

6. After these procedures are completed, you can also clean the sewage interception net by the way. If you find it too troublesome, it won't have much impact if you don't clean it.

Ways to clean your own underfloor heating pipes at home:

Clean the floor heating pipe first close the water inlet valve and outlet valve, install a water pipe at the head of the return pipe, close all the water distribution valves, only one valve is open, open the water inlet valve and outlet valve of the heating, after flushing for a period of time, open the water distribution valve in turn, and then clean the other valves and pipes.

1. First of all, we need to turn off the inlet and outlet valves to separate our heating from the heating of the whole building, so that we can clean it. Usually the valve is perpendicular to the pipe in the horizontal direction, i.e. closed.

2. Install a water pipe at the blocked place of the return pipe. If you have good practical experience, you can install it yourself. If you feel that your skills are not good, you can go to a pipe cleaning company.

This equipment can also be installed at the end of the heating period. During heating, it can cause some trouble because there is too much water in the pipes, but it's not a big deal.

3. Close all the water distribution valves, only one valve is open, and then connect a pipe to your own sewer.

4. Turn on the inlet valve of the heater, and then turn on the faucet, the hot water will flow out, and there will be a lot of dust. What is cleaned in this way is the open manifold.

5. Rinse for a while until the water becomes a little clear. In this way, they can open the water distribution valve in turn, and then clean the other valves and pipes, so that the floor heating pipe cleaning is completed.

6. You can also clean the filter screen, there are a lot of stains inside, if you are too troublesome, don't wash it.

Choose professional floor heating pipe scale cleaning products and floor heating descalers. Chemical soaking for geothermal cleaning, projectile cleaning for geothermal cleaning, pulsed wave physical cleaning for geothermal cleaning.

1. Chemical soaking for geothermal cleaning

Advantages: Thorough cleaning, can fully dissolve the slime attached to the pipe wall, high-quality food-grade raw materials will not cause corrosion to the geothermal pipe;

Disadvantages: The chemical reagents used in geothermal cleaning, strong acid or strong alkali preparations, do not consider the bearing capacity of geothermal pipes, and the pipeline and related components are seriously corroded, and the purpose of scale removal cannot be achieved without corrosion.

2. Projectile cleaning of geothermal cleaning

Advantages: Thorough cleaning, using the friction between the cleaning bomb and the pipe wall to remove the slime attached to the pipe wall, without damaging the geothermal pipeline;

3. Pulsed wave physical cleaning of geothermal cleaning

Advantages: no need for chemicals, no disassembly of geothermal pipes, due to its unique cleaning principle, the main pipeline and valve of the geothermal separator can be cleaned at the same time, so as to avoid long-term scaling and valve blockage;

Disadvantages: It is ineffective for scale, the construction is limited by space, some family geothermal water separators are placed in hidden places, and it is not easy to construct when the two ends of the water separator are too close to the wall.