How to clean underfloor heating? Home decoration floor heating, how to clean floor heating?

Generally speaking, there are three kinds - chemical soaking, projectile cleaning, and pulsed wave physical cleaning. Among them, the pulse cleaning method is the most used for floor heating, which can clean the scale and impurities of the floor heating pipe and water separator at one time.

Floor heating cleaning is generally calculated by the square, according to the heating area of geothermal heat, now it is generally 5-15 yuan a square is more reasonable.

There is also a kind of calculation according to the circuit, a circuit is basically 50-150 yuan, now most of the cleaning unit door-to-door cleaning costs are basically like this, different companies ** way is different.

For example, in Hangzhou, for example, the cost of cleaning a house with a heating area of 80 square meters is about 300 to 700, depending on the charging mode of the floor heating cleaning company, the cleaning institutions are different, the cleaning methods are different, and the cleaning fees charged are not the same.

For specific conditions, please call us or make an appointment for cleaning.

Generally, it is cleaned once every 3-5 years and is cleaned by professionals. There are generally three methods of cleaning floor heating: chemical immersion, projectile cleaning, and pulsed wave physical cleaning.

The cleaning time can be selected before heating, during heating and after heating. Extended Information: Chemical Immersion:

It should be said that the cleaning effect is very good, but because it is easy to corrode and aging the floor heating pipes and system components, as well as polluting the discharge, the heavier ones in the pipeline are not easy to discharge. None of them are currently adopted in this way. Projectile cleaning:

Projectile cleaning decouples the floor heating pipe from the water divider, puts the cleaning bomb in the floor heating pipe, and then uses compressed air to eject the cleaning projectile into the floor heating pipe, and comes out from the other end of the pipe to achieve the purpose of cleaning. The cleaning effect is good, and the tube can be restored to its original color. The disadvantage is that the efficiency of unpacking is relatively low, and it is easy to get stuck when encountering joints and bending of the floor heating pipe, and the unwinding of the pipe is inevitably difficult to repair the damage to the floor heating pipe, and the safety of the floor heating pipe cannot be 100% guaranteed.

Pulse wave physical cleaning: The medium of pulse cleaning is gas, water, ultrasonic, etc., and the purpose of cleaning is achieved by impact and vibration on the inner wall of the floor heating pipe by pulse wave and vibration wave. This method is cleaned one by one, without unraveling.

The cleaning effect is relatively good, it can clean out the embroidery scale and sediment in the tube and quickly remove it from the tube, which is simple to operate, safe and environmentally friendly. It is the mainstream way of floor heating cleaning.

Cleaning the geothermal heat is so easy that everyone can easily do it with a few operations.

How to clean underfloor heating? Choosing the cleaning time and method is very important, many people don't understand, take a look.

The continuous rain has made the temperature begin to drop, and many families have begun to enable floor heating, however, some users find that the floor heating that has been shelved for a year is not as warm as last year, and a check found that it is because of a large amount of dirt in the floor heating pipe, which affects the normal end of the floor heating connected to the tap water through the cleaning machine into the floor heating pipe, because the input water is under pressure, the dirt and impurities in the pipe will be flushed out from the water outlet of the water separator, the pipe is clean, the water flow speed is fast, and the heating is much better than before!

Floor heating, the important thing is maintenance, not cleaning, it is recommended to add F1 protective agent, no need to clean, no matter how good the way is not thorough, of course, there is no maintenance in the early stage, now cleaning can also be cleaned with F3 cleaning agent, of course, it can also be combined with ultrasonic to clean the cost is low, the cost of pipeline blockage is relatively high, now the general promotion of pulse cleaning, chemical cleaning is not conducive to environmental protection and corrodes metal and pipes, egg shooting cleaning is not suitable for a long time has not been cleaned and there are joints of the floor heating pipeline, floor heating cleaning is not a trivial matter, Professional cleaning is more assured!

The service life of the floor heating system is mainly the service life of the buried pipe, because the above-ground part can be replaced, therefore, Tianjin Capital Decoration reminds you that the floor heating pipe selection is the key to the service life. At present, the pipes used in the floor heating system are generally plastic aluminum pipes, PE RT (high temperature resistant floor heating. This is also a disadvantage of water floor heating, because it needs to be cleaned regularly.

Floor heating is more troublesome to clean, generally the scale will be cleaned with chemical descaler, but for floor heating, the descaler cleaning is too troublesome, it will block the HVAC pipeline, and the floor heating pipe is often cleaned, it will also lead to pipe perforation, then the maintenance is very Floor heating pipe cleaning is relatively rare, and the amount of work is large, and the floor heating is a hidden project, maybe a link goes wrong will lead to problems with floor heating, so this kind of professional problem or find a professional master to do, it is not recommended to "do it yourself." ”。

Floor heating is generally cleaned through the cycle of water exchange, and some sediment is removed through multiple rinsing.

There are three ways to clean floor heating, first, you can buy a special cleaning agent for cleaning, second, you can use catapult cleaning, third, you can use physical pulse cleaning, these three cleaning methods have their own advantages and disadvantages, but they can well remove the dirty stains of floor heating.

All the valves should be closed, the screws should be unscrewed, and the filter should be found so that it can be cleaned and it will work very well.

You can go to a professional team to clean, there is no way to clean it yourself, and the price of cleaning is not very high, which is acceptable.

Generally, it is cleaned by continuous water supply, and some chemicals are added to clean it more cleanly.

How to clean floor heating, floor heating is the most commonly used way of heating in winter, floor heating is very important to us in winter, and the heating effect is particularly good. Floor heating also needs to be cleaned after a long time, so how to clean the floor heating? Let's take a look at these related trivia.

How to clean the floor heating

1. Chemical agents

Regarding the question of how to clean the floor heating, many people will use chemical soaking to achieve the cleaning effect. In the process of using chemicals, because of the soaking of chemicals, some scale and mud in the pipeline equipment are taken off, so that the pipeline is smoother and will not block the water flow. Cleaning pipes in this way is not only effective, but also relatively safe.

2. Projectile cleaning

Nowadays, there are many people who use the way of projectile cleaning to clean the pipeline, and the projectile cleaning mainly uses the friction between the cleaning bomb and the pipeline to achieve the purpose of cleaning, and the use of this method not only does not damage the pipeline, but also can effectively remove more impurities and dirt at the same time, but the pipeline needs to be disassembled when using this way to do cleaning, but the time and labor required are relatively large, and it needs to be used selectively in combination with the actual situation.

There are generally several ways to clean underfloor heating

1 Rinse with clean water. This is relatively simple, and it is non-corrosive, so it will not have a bad effect on underfloor heating. However, the cleaning is not thorough.

2 Chemical cleaning.

3. Physical ejection cleaning method.

4 High pressure pulse cleaning.

General Operational Procedures

1. Close the water supply and return water isolation valves of the water separator;

2. Connect the pulse induction pipe, and connect the digital computer pulse generator with the water separator general bearing plug end;

3. Connect the water pipe, connect the water source and the computer pulse generator;

4. Connect the gas pipe, connect the air compressor and the computer pulse generator;

5. Connect the sewage pipe, connect one end to the head of the water separator return water bearing plug, and insert the floor drain at one end. Start the cleaning.

1. First of all, the valve of the water inlet and outlet should be closed, and the heating system of your home should be separated from the heating system of the whole area, so as to better operate later.

2. Install a faucet at the position of the plug of the return pipe. You can choose to install it yourself, or you can ask a plumber to do it.

3. Close the water distribution valve in turn, and then leave only one in the open state. The faucet installed at the back is connected to a section of hose that leads directly to the sewer in your home.

4. Open the water inlet valve for heating, and then open the valve of the faucet, and the hot water will be discharged along the water, so that the dirt will also be brought out by the water flow, so that it will have a cleaning effect.

5. After rinsing for a period of time, observe the quality of the water, and then follow the above methods to clean each pipe.

6. After these procedures are completed, you can also clean the sewage interception net by the way. If you find it too troublesome, it won't have much impact if you don't clean it.

Jet type plus cleaning agent cleaning: using a special high-flow jet cleaning machine, equipped with a cleaning agent made of high-quality environmentally friendly preparations and corrosion inhibitors, the slime attached to the pipe wall can be fully dissolved. Projectile cleaning:

The friction between the cleaning bomb and the pipe is used to remove the slime attached to the pipe wall, and any chemical cleaning agent can be used without using the round, but the floor heating pipe needs to be disassembled. Pulse wave physical cleaning: through the high-pressure water flow, the pipeline is washed, and the impurities in the pipeline are removed by physical means, without chemical cleaning agents and without dismantling the floor heating pipes.

1. Jet type plus cleaning agent: the use of a special high-flow jet cleaning machine, equipped with a cleaning agent made of high-quality environmental protection preparations and corrosion inhibitors, can fully dissolve the slime attached to the pipe wall.

2. Projectile cleaning: use the friction between the cleaning bomb and the pipeline to remove the slime attached to the pipe finger wall, without using any chemical cleaning agent, but need to disassemble the floor heating pipe.

3. Pulse wave physical cleaning: through the high-pressure water flow, the pipeline is washed, and the impurities in the pipeline are removed by physical means, without chemical cleaning agents and without disassembling the floor heating pipe.

Cleaning floor heating pulse cleaning method is currently the most used cleaning method.

The pulse cleaning method is to use high-pressure pulse air flow into the water separator, and control each geothermal pipe by the shunt method, the high-pressure pulse air flow continuously washes the wall of the geothermal pipe, and the impurities and dirt are continuously discharged with the high pressure, and the whole cleaning process has no damage to the water separator, which is the preferred geothermal cleaning method at present.

The automatic pulse virtual fiber geothermal cleaning uses a combination of gas, water and electromagnetic pulses to convert into kinetic energy through internal vortex power, and carries out high-speed movement in the form of tiny molecules, through the thermal energy, kinetic energy and electromagnetic pulse in the operation process. The dirt in the pipe wall is broken down and flushed out of the pipe with water molecules to achieve the effect of cleaning.

Pulse cleaning geothermal tube cleaning features are:

1. Do not use any chemicals, have no corrosion to the pipe network, and discharge green and environmental protection.

2. No blockage, strong applicability. Because the cleaning is based on gas and water as the medium, peeling off layer by layer, it will not cause blockage in the pipe; It can be applied to coils in various structural designs.

3. Efficient, fast, time-saving and labor-saving. Cleaning is carried out at the water separator of each user, and can be cleaned in a single tube or multiple pipes at the same time. Do not destroy the original structure of the heating equipment and the user's decoration design.

Generally, it only takes two hours to clean 100 square meters of geothermal heating pipes.

4. The cleaning quality inspection method is simple. You can observe the cleaning effect with your eyes, and you can also use the method of comparing the two pipes before and after cleaning to test the cleaning effect, which is clear at a glance.

Geothermal cleaning can be cleaned all year round, the best time is the early stage of the heating process every year, due to the different water quality of each lot for more than two years has not been cleaned customers at any time to clean to prevent blockage, winter heating customers should pay attention to drainage and anti-freezing.

1. Chemical soaking: advantages - thorough cleaning, can fully dissolve the slime attached to the pipe wall, high-quality food-grade raw materials will not cause corrosion to the geothermal pipe; Deficiencies - most of them use low-cost strong acid preparations, which are easy to cause corrosion to pipelines and related components.

2. Projectile cleaning: advantage - cleaning is more thorough, using the friction between the cleaning bomb and the pipe wall to remove the slime attached to the pipe wall, without damaging the geothermal pipeline; Insufficient - the geothermal pipe needs to be disassembled, the underground pipeline has a joint that is not suitable for construction, and the cavity is easy to make the cleaning bomb stuck in the pipeline; At the same time, it is easy to cause secondary damage to the original water separator, valve and other related parts.

3. Pulse wave physical cleaning: advantages - no need for chemicals, no disassembly of geothermal pipes, cleaning is more thorough, due to its unique cleaning principle of slow care, the main pipeline and valve of the geothermal water separator can be cleaned at the same time, so as to avoid long-term scaling and valve blockage; Deficiencies - the construction is limited by space, and some household geothermal water separators are placed in hidden places, and it is not easy to construct when the two ends of the water separators are too close to the wall.

Floor heating is a heating system often used in northern China, which keeps the room temperature in a comfortable area, but if you don't pay attention to it, its use effect and life will be affected. Therefore, PCHOUSE will introduce you to how to clean floor heating today.

1. Filter cleaning.

First of all, close the inlet and return valves connected to the conduit, then open the filter and filter screen and clean it after cooking, and check whether the filter screen is damaged or blocked. If there is any damage, it should be replaced with a filter of the same specification and installed as it is.

2. Chemical soaking Chemical soaking and cleaning can fully dissolve the slime attached to the pipe wall and will not cause corrosion to the floor heating pipe. First of all, open the inlet pipe of Huxian floor heating hot water, inject diluted floor heating cleaning liquid, close the cold water valve after the floor heating pipe is filled with water, start the circulating pump to circulate for 30 minutes, and then open the cold water valve, and put the turbid water clean until there is clean water flowing out of the outlet pipe.

3. Projectile cleaning This method uses the friction between the cleaning bomb and the pipe wall to remove the slime attached to the pipe wall. The disadvantage of this cleaning method is that the underfloor heating pipes are dismantled. If there are joints in the underground pipeline, the construction is very inconvenient.

In addition, it may also cause secondary damage to the original manifold, valve and other related parts.

4. Pulse cracking wave physical cleaning This method is more convenient, without chemicals and disassembling floor heating pipes, and the cleaning effect is good. It can clean the main circuit and valve of the floor heating manifold at the same time to avoid long-term fouling and valve blockage. The disadvantage of this cleaning method is that the construction is limited by space.