Do I need to keep the dipped beam during the U turn of the C1 subject 3 night exam?

1. After the driver gets into the car, turn on the small lights first and prepare for getting into the car. Before the car starts, turn on the low beam and left turn signal.

2. When the car is driving, when passing through the road section with street lights and good lighting, low beam should be used. High beams should be used when passing through unlit, poorly lit road sections. When passing through sharp bends, slopes, arch bridges, pedestrian crossings, or intersections that are not controlled by traffic lights, high and low beams should be used alternately.

When driving at night in wind, rain and snow, anti-fog lamps or anti-glare low beams should be used, and high beams should not be used to avoid dazzling light curtains and affect the line of sight.

3, when there is a car at night, should be 150 meters away from the car, close the high beams to use low beams, reduce the speed, choose the appropriate meeting place, when the two cars are about 50 meters apart, should close the headlights, use small lights, do not use anti-fog lights, and grasp the direction to the right slowly, when the two heads are parallel, you can turn on the headlights, if the car does not turn off the high beams in time or the road is complicated, if necessary, you should pull over.

4. When you need to overtake at night, you should continuously change the high and low beams or use the horn to announce in advance, and you can only overtake after the car in front gives way.

5. When following the car in close proximity in the same direction, keep a safe distance and use low beams.

6. When temporarily parking on the side of the road at night, the headlights should be turned off and the illumination lights should be turned on to remind pedestrians and other drivers to pay attention.

7. Use lights when turning at intersections at night:

Operating procedures: The examiner issues the instruction "Please change the headlight to high beam", and the examinee does not change the light after receiving the instruction or changes the light incorrectly is unqualified; When in the state of high beam, the examiner will issue the command "please turn left or right at the intersection ahead", and the examinee should change the high beam to low beam after receiving the instruction, otherwise it will not be qualified.

Yes, during the U-turn, you have to turn on the double flash all the time.

Subject 3. Mock night light exams.

When the voice announces "The exam starts. Please turn on the light", at this time you need to turn on the low beam, no matter which project you operate later, you do not need to turn off the low beam, until the end of the light test, the voice broadcast "please turn off the light", you can turn off the low beam.

The specific methods of the three dozen lights are as follows:

1. Driving at night under the condition of no street lights and poor lighting.

Correct operation: Width indicator light.

High beams (Another way to do this is to turn on the headlights and hear the headlights.)

Switch to high beam before operating, and the coach will be the subject during the exam).

2. Please change the headlights to high beams. Correct operation: Remain motionless with the high beams on; Switch to high beam with low beam on.

3. At night on narrow roads with non-motorized vehicles.

Will car. Correct operation: Turn on the low beam of Collapse Kai.

4. Meet the motor vehicle at night. Correct operation: Turn on the low beam.

5. Passing through sharp bends and slopes at night. Correct operation: The high and low beams flash twice alternately.

6. The group calls to follow the car in the same direction at close range at night. Correct operation: Turn on the Zen shouting light.

7. Overtake the vehicle in front at night. Correct operation: left turn signal, alternating high and low beams.

8. If there is a failure on the road at night, the traffic is difficult to move. Correct operation: Turn off the headlight group, turn on the enlightenment wide light and warning light.

First, it is different. At night, when passing through an intersection that is not controlled by a traffic light, slow down in advance, alternately use high and low beams, pay close attention to the traffic situation ahead, go straight at the intersection, and use low beams to pass.

2. Driving test subject 3 lighting test operation method:

1. If you are about to turn at the intersection, please use the correct lights (alternate high and low beams no less than 2 times);

2. If you are about to pass through a sharp bend, please use the correct lights (alternate high and low beams no less than 2 times);

3. If you are going to cross the arch bridge, please use the correct lights (alternate high and low beams no less than 2 times);

4. If you are going to pass through an intersection without traffic signal control, please use the correct lights (alternate high and low beam lights no less than 2 times);

5. If you are going to meet other vehicles, please use the correct lights (turn on the low beams);

6. If you are driving on a low-visibility road, please use the correct lights (turn on the high beams);

7. If you are going to pass through the slope, please use the correct lights (alternate high and low beams no less than 2 times);

8. If you are going to cross the crosswalk, please use the correct lights (alternate high and low beams no less than 2 times);

9. If you are about to overtake, please use the correct lights (turn on the left turn signal first, then alternately use the high and low beams no less than 2 times, and then turn on the right steer.)

3. Go straight through the intersection at night, most netizens' answer is alternating between high and low beams, but in fact, the lighting system installed on the test car, as long as it is operated according to this answer, it will be unqualified, and the correct operation is low beam. I don't know if any netizens have encountered this situation? "Go straight through the intersection" and "go through the intersection" may have different concepts.

Passing through the intersection at night is the same as going through the intersection at night. Both are used alternately with high and low beams.

1.Ready to pass through the intersection are low beams;

2.Passing through the intersection with a signal light is a low beam;

3.Passing through unsignaled intersections is alternating between near and far.

Subject 3 goes straight at night, and the lights should be the same as passing through the intersection at night, I think so, I don't know if it's right.

When a motor vehicle passes through a sharp bend, a slope, an arch bridge, a pedestrian crossing or an intersection without traffic signal control at night, it shall alternately use high and low beam lights.

Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China

Article 57 Motor vehicles shall use turn signals in accordance with the following provisions:

1) When turning left, changing lanes to the left, preparing to overtake, leaving the parking place or making a U-turn, the left turn signal should be turned on in advance;

2) When turning right, changing lanes to the right, returning to the original lane after overtaking, and stopping on the side of the road, the right turn signal should be turned on in advance.

Article 58 When a motor vehicle is driving at night without street lights, with poor lighting, or in low visibility conditions such as fog, rain, snow, dust, hail, etc., it shall turn on its headlights, marker lights, and rear position lights, but when the rear vehicle driving in the same direction is driving in close proximity to the vehicle in front, it shall not use high beams. When driving in foggy weather, motor vehicles should turn on fog lights and hazard warning flashers.

Article 59 When the ruler silver bullet train passes through sharp bends, slopes, arch bridges, pedestrian crossings or intersections without traffic signal control at night, it shall alternately use high and low beam lights.

When a motor vehicle approaches a sharp bend, the top of a ramp and other road sections that affect the safe visual distance, as well as overtaking or encountering an emergency, it shall slow down and sound its horn to signal.

If a motor vehicle breaks down on the road or a traffic accident occurs, obstructing traffic and making it difficult to move, it shall turn on the hazard warning flashing lights in accordance with the regulations and set up warning signs at a distance of 50 meters to 100 meters behind the vehicle, and at night it shall also turn on the light and rear position lights at the same time.

Precautions for the three-night test of the subject:

The night test is a new test content in subject 3, which assesses the knowledge of students to use lights at night and in low visibility situations, so the main attention is paid to the use of lights when taking the night test.

Start: Detour from the right front of the car in front of the cockpit door: Report.

Get on the bus with the examiner's permission to lean on the door, put your right foot on the accelerator, put your left foot on the clutch, adjust the seat and mirror, and fasten your seatbelt. Check the engine gauge with the throttle, turn on the headlights, turn off the double flash, hit the left turn signal, and go into 1st gear.

Step on the clutch, put in gear, turn on the left direction light, turn on the headlights, turn off the ceiling lights, and release the handbrake. Look in the left rearview mirror and start into the carriageway. Directly behind the body, hang 2nd gear, turn on the high beams, accelerate, hang 3rd gear, accelerate, hang 4th gear.

When crossing the intersection, the far and near lights are Kaba 4 times, when you encounter the opposite car, Kaba is a time, overtaking Kaba is four times, stop, first Kaba is a moment, hit the right turn signal, brake, step on the clutch, and stop.

When pulling over, pick up neutral, pull on the handbrake, turn on double flashing, and turn off the headlights.

1.When you are about to turn at an intersection, use the correct lights (alternate high and low beams no less than 2 times);

2.If you are going to pass through a sharp bend, use the correct lights (alternate high and low beams no less than 2 times);

3.If you are going to cross an arch bridge, please use the correct lights (alternate high and low beams no less than 2 times);

Under normal circumstances, there will be a certain prompt during the subject 3 exam, telling you that the front lighting is poor, or the front lighting is good, if the front lighting is poor, you need to turn on the high beam, if the front lighting is good, you need to change to low beam.

If there are no traffic lights at the intersection, you can use high beams, and if the lighting is good, you can use low beams.

1. When meeting the car, it is necessary to use low beam lights within 150 meters away from the incoming car;

2. When chasing the vehicle behind you, you must use low beams;

3. When overtaking, the turn signal must be turned on and the vehicle in front must be prompted by the dipped beam change;

4. When passing through the crossing, it is necessary to use the low beam to change the low beam to remind the vehicles inside and outside the street intersection to pay attention.

In addition, when driving at night, you should also pay attention to the speed of the vehicle, pay attention to the position of the vehicle when you meet the car, do not lean too far to the left, pay attention to the pedestrian or vehicle on the right, and accurately estimate the position of the vehicle when passing through bridges and going uphill.

Driving at night without street lighting or in poorly lit conditions – headlights on, meeting non-motorized vehicles on narrow roads and narrow bridges at night – low beams.

Crossing sharp bends, slopes, arched bridges, pedestrian crossings, or junctions that are not controlled by traffic lights at night – alternate high and low beams (changing lights more than twice).

In the event of a breakdown on the road or a traffic accident at night that obstructs traffic and makes it difficult to move - convert the headlights into width indicator lights + warning lights.

Driving in foggy days - headlights on + fog lights + warning lights.

Follow the car in the same direction at night at close range - low beams.

Meeting with a motor vehicle at night - low beams.

Meeting non-motorized vehicles on narrow roads at night - low beams.

During the exam, the password is a combination of these eight items, and it is very effective to memorize this and then listen to the password to practice.

Note: For the third voice prompt is separated, for example, the voice prompt during the test may be crossing an arch bridge or pedestrian crossing at night.

Passing through sharp bends and slopes at night.

Crossing an intersection that is not controlled by a traffic light at night.

In all three cases, the high and low beams should be used alternately (changing the light more than twice).

Subject 3: Lighting: How to alternate the lights on the high beams.

What lights are not light, the third test subject is a person from his own driving school, and he will pass it if he gives 100 yuan, otherwise even if you pass it yourself, he will give you the whole It depends on the mood of others.

There are two words when there are far and near lights alternately.

According to Article 48 of the Road Traffic Safety Law:

1, on the road without central isolation facilities or without center line, the night meeting car should be changed to low beam lights within 150 meters away from the opposite direction of the vehicle;

2. Low beams should be used when meeting with non-motorized vehicles on narrow roads, narrow bridges;

3, when the motor vehicle has no street lights at night, poor lighting or low visibility conditions such as fog, rain, snow, dust, hail, etc., the rear car driving in the same direction and the front car should use low beams;

4, when motor vehicle passes through sharp bends, slopes, arch bridges, pedestrian crossings or intersections without traffic signal control at night, should alternately use high and low beam lights;

5. When driving on the road without lighting conditions at night, when the speed is less than 30 kilometers per hour, low beam lights can be used; High beams can be used at speeds above 30 km/h. At night, vehicles should use low beams when passing through well-lit road sections.