How to adjust the cold storage thermostat? How to debug the thermostat on the cold storage

Cold storage thermostat operation adjustment:

1. Operation mode: 1. Probe 1 is the storage temperature control, which is generally installed at the far end of the fan. Set the upper and lower temperature limits to control the operation of refrigeration equipment.

2. The probe 2 is controlled by the fan, which is generally installed at the proximal end of the fan. The temperature difference is generated compared with the probe 1, and the upper and lower limits of the temperature difference are set to control the operation of the fan. It not only fully ensures the temperature uniformity in the warehouse, but also minimizes the running time of the fan.

3. Probe 3 is defrost control, which is generally installed on the evaporator. There are two modes: timed start and temperature difference start. The start and end of defrosting are controlled by temperature at the same time, and reasonable parameter setting can achieve the best energy saving effect.

4. Increase the refrigeration delay and fan delay, set these two parameters, and reduce the operation of the machine with a reasonable delay.

Press and hold the [set] button for 3s to enter the parameter item selection mode, and set the indicator light to be on; The LED shows the parameters of the last adjustment.

Press [ ] or [ ] to select the capacity row parameter item (f1......f6), after the parameter item is selected, press the [set] key to display the parameter setting value of the corresponding parameter item;

Press and hold the [set] key, and press the [ ] key or [ ] key at the same time to set the parameter value, and hold the [ ] or [ ] key to quickly increase or decrease the parameter value;

After the parameter value of a parameter item is set, press the [ ] or [ ] key to select other parameter items, and repeat the above steps to set the parameter value.

After all parameters are set, press the [rst] button to confirm and reset, and the setting indicator is off. If there is no button operation, after 30s, the machine will automatically confirm the storage and reset, and set the indicator light to off.

1. Set the temperature (below minus 15 degrees Celsius as an example).

2. Set the temperature difference, if it is set to 5, that is to say, the machine will start when it reaches minus 10 degrees, and the machine will stop when it reaches minus 20 degrees.

3. The defrosting time is set, if it is set to 8 hours, it is a defrost every 8 hours.

There is a valve directly. Just twist it.

2. The "Boot Temperature" indicator light is on, and every time you press and immediately release the "Set View" button in the future, you will enter the next parameter setting (cyclic operation), and the corresponding parameter indicator will be on.

How to regulate the temperature of cold storage.

Hello, I have seen your question and am sorting out the answer, please wait a while

I click the mark adjustment at the top and bottom directly.

I do.

But I don't know how to tune it.

Wait a moment 1, user menu settings: In the running state, press and hold "Settings". When the "View" button lasts for more than 5 seconds until the "Display Temperature" display window displays "set", it means entering the user menu setting;

2. The "Boot Temperature" indicator light is on, and every time you press and immediately release the "Set View" button in the future, you will enter the next parameter setting (cyclic operation), and the corresponding parameter indicator will be on.

3. After entering the user menu, press the " (volume flag) or " button to modify the setting parameters in the "shutdown temperature" display window.

Hello, the specific operation steps are as follows:1. In order to prevent misoperation and avoid idling, you must press the "set" button 3 times in a row to enter the setting state.

2.After the controller enters the setting state, the lower temperature setpoint is displayed first (the prompt symbol is "L"), press the " or " " button to change the set value until it meets the requirements. (When a negative value is set, the minus sign flashes).

Then press "set" to display the upper temperature setpoint (the prompt symbol is " " At this time, you can press the " or " " key to change the set value until the Yu J meets the requirements (when set to a negative value, the minus sign flashes). 3.Press the "set" button again to display the compressor shutdown delay time (the prompt symbol is "Y").

At this time, press the "Town Stove Flush" key to change the setting value until it meets the requirements. Then press the "SET" button to display the control mode (the prompt symbol is "J"), and then you can press the " " button to select the cooling mode (the prompt symbol is JCC) and the heating mode (the prompt symbol is JHH). 4.

Press the "set" button again to display the temperature correction value (prompt is "i"), generally no temperature correction is required; If temperature correction is required, you can press the " " or " " button to change the setting value until it meets the requirements. 5.Exit settings; No button operation within 16 seconds, the controller will automatically exit the setting state, the set value will be saved, and the display screen will still display the temperature measurement value.

Warning: If you turn off the machine immediately after setting, the new setting values will not be saved permanently.

Summary. Cold storage is a kind of equipment used to store low-temperature products, where temperature regulation is very important, because different products require different storage temperatures. Here are some ways to adjust the temperature of cold storage:

1.Regulate the refrigeration system of the cold storage: The refrigeration system plays a vital role in the regulation of the temperature of the cold storage.

By adjusting the working state of the compressor, expansion valve, condenser and other components in the refrigeration system, the temperature of the cold storage can be adjusted. 2.Adjust the ventilation system of the cold storage:

The ventilation system is also one of the important factors in the temperature regulation of the cold storage, which can achieve temperature regulation by controlling the air circulation and flow rate. By adjusting the switch and working status of the vents, fans, exhaust pipes and other components in the ventilation system, the temperature of the cold storage can be adjusted. 3.

Control the doors and windows of the cold storage: The doors and windows of the cold storage can also affect the temperature of the cold storage. If the doors and windows are not tight, it will affect the stability of the temperature inside the cold storage.

By adjusting the degree of opening and closing of doors and windows, the temperature of cold storage can be regulated. 4.Install the appropriate temperature controller:

The temperature controller tracks the temperature in the cold room and regulates the temperature by controlling the operation of the refrigeration system. Depending on the storage requirements of the product, different types of temperature controllers can be installed. When adjusting the temperature of the cold storage, it is necessary to make reasonable settings according to the storage requirements of the product and the ambient temperature and other factors, and at the same time, it is also necessary to regularly maintain and maintain the cold storage equipment to ensure its normal operation and stable temperature.

Excuse me, but please go into more detail?

Cold storage is a kind of equipment used to store low-temperature products, in which the regulation of temperature is very important, because different products require different storage temperatures. Here are some ways to adjust the temperature of cold storage:1

Regulate the refrigeration system of the cold storage: The refrigeration system plays a vital role in the regulation of the temperature of the cold storage. By adjusting the working state of the compressor, expansion valve, condenser and other components in the refrigeration system, the temperature of the cold storage can be adjusted.

2.Adjust the ventilation system of the cold storage: The ventilation system is also one of the important factors for the temperature regulation of the cold storage, which can achieve temperature regulation by controlling the air circulation and flow rate.

By adjusting the switch and working status of the vents, fans, exhaust pipes and other components in the ventilation system, the temperature of the cold storage can be adjusted. 3.Control the doors and windows of the cold storage:

The doors and windows of the cold storage can also affect the temperature of the cold storage. If the doors and windows are not tight, it will affect the stability of the temperature inside the cold storage. By adjusting the degree of opening and closing of doors and windows, the temperature of cold storage can be regulated.

4.Install the right temperature controller: The temperature controller can track the temperature in the cold room and regulate the temperature by controlling the operation of the refrigeration system.

Depending on the storage requirements of the product, different types of temperature controllers can be installed. When adjusting the temperature of the cold storage, it is necessary to make reasonable settings according to the storage requirements of the product and the ambient temperature and other factors, and it is also necessary to regularly maintain and maintain the cold storage equipment when the same branch is poor to ensure its normal operation and stable temperature.