How to disassemble the clutch of Haier XQS55 728 dual power washing machine 5

First, first open the lid of the washing machine and take out the wave wheel, there is a screw in the middle of the wave wheel, and there is a plastic cover on the screw.

Second, after taking out the wave wheel, screw out the screw that fixes the clutch, the screw should be 24 27, quite a large one.

Third, put the washing machine flat (head to the ground) from the bottom of the washing machine to remove the screws that fix the clutch, after disassembly, if you can't get it out by hand, then find an extended wooden stick from the washing machine and knock it with a hammer, and the clutch is disassembled.

Put the washing machine down. Remove the 2 screws of the motor, then remove the 8 screws of the clutch, and then remove the screws of the wave wheel, and remove the screws under the wave wheel {if it is a nut, take the sleeve to remove}, so that you can take out the clutch, if you don't understand. It is best to call the after-sales service to repair.

I am from Haier after-sales service, thank you.

My Haier washing machine also broke down, and when it dried, it was louder than a train. It is relatively lazy and has not been dismantled, it may be that the inner barrel must be brought out before it can be dismantled.

The clutch of the dual-power washing machine is not easy to remove.

There are four at the bottom; Screws, just remove them.

The clutch of the dual-power washing machine should use a large sleeve.

Or find customer service or after-sales personnel, otherwise you may not be able to install it after dismantling.

Well, it is recommended to find after-sales personnel to assist in dismantling, and it may not be easy to install it yourself.

Summary. The program controller is disassembled.

First of all, remove the fixing screws on the back of the upper cover of the washing machine, and then remove the upper cover. Then turn the program controller knob to the stop position in a clockwise direction, push it outward with the program controller knob, and use the screw to install the program controller to screw down, and the operation panel can be removed.

How to disassemble the Haier washing machine XQS75-BZ1228 motor.

To remove the program controller, remove the fixing screws behind the upper cover of the washing machine, and then remove the upper cover. Then turn the program controller knob to the stop position in a clockwise direction, push it outward with the program controller knob, and use the screw to install the program controller to screw down, and the operation panel can be removed.

To remove the program controller, remove the fixing screws behind the upper cover of the washing machine, and then remove the upper cover. Then turn the program controller knob to the stop position in a clockwise direction, push it outward with the program controller knob, and use the screw to install the program controller to screw down, and the operation panel can be removed.

2. The disassembly of the door switch will open the door of the washing machine, take out the wire snap ring of the door sealing ring, remove the sealing ring, and remove the door switch with screws to the screws on the removal fixed frame.

3. Disassemble the upper cover of the washing machine of the water level switch, open it, and unplug the plastic pipe of the water level pipe and the water level key; Use a screw driver to remove the fixing screws on the electrical board and remove the water level switch.

4. Disassemble the two-speed motor, remove the screws on the back cover of the washing machine, and remove the rear cover; Unplug the wire on the motor socket, remove the nut that holds the motor in place, and pull out the motor screw.

5. Disassemble the fork frame of the outer barrel and remove the back cover of the washing machine, tilt the washing machine forward, and place it on the foam cushion; Remove the V-belt, then remove the connecting screws of the pulley and the inner drum shaft, and remove the large pulley; Hit the inner barrel shaft with a rubber hammer, and the outer cylinder fork frame is removed.

Summary. Hello dear, Haier washing machine XBQ75-M1269S clutch spring size is: outer diameter: 35mm; Inner diameter: 25mm; Height:; Aperture:.

Haier washing machine XBQ75-M1269S clutch spring how big.

Hello dear, Haier washing machine XBQ75-M1269S clutch spring size is: outer diameter: 35mm; Inner diameter: 25mm; Height:; Aperture:.

How big is the clutch nut.

Pro, the specification of the Haier washing machine XBQ75-M1269S clutch nut is M10. It is a standard thread specification with an outer diameter of 10 mm and a pitch of millimeters.

How big a socket wrench to use.

The size of the wrench for the Haier washing machine XBQ75-M1269S clutch nut should be 14mm. Also, in order to properly remove and install the clutch nut, it is recommended to use a wrench of a larger size, such as 17mm or 19mm.

Summary. Pro, the spring is at the bottom of the clutch, first remove the pulley (clutch) and then remove the plastic gear to see the spring, turn the pulley by hand, if it can't be rotated, it is the internal corrosion of the planetary gear, or the rust between the oily copper lining and the shaft. When changing, pay attention to a small hook at one end of the spring, hook it into a small hole in the plastic gear, and then screw the plastic gear and the square wire spring back counterclockwise, and tighten the nut.

Hello, dear, very happy with your question, Haier little prodigy XQB50 a 7288A washing machine clutch spring is what size, help you find out, Haier little prodigy answer Yu XQB50 a 7288A washing machine clutch Changju mold spring is the size is 810 710 88 I hope mine can help you, I wish you good health, happy and patient!

Pro, the spring is at the bottom of the clutch, first remove the pulley (clutch) and then remove the plastic gear to see the pin, turn the pulley by hand, if it can't be rotated, it is the internal corrosion and jamming of the planetary gear, or the rust between the oily copper lining and the shaft. When changing, pay attention to a small hook at one end of the spring, hook it into a small hole in the plastic gear, and then roll the balance counterclockwise to screw the plastic gear and the square wire spring back, and tighten the nut.

I want to buy a hug spring, but I don't know the size.

Pro, the holding spring is size 810 710 88

What is the size of the clutch spring of Haier XQB60-S12588 washing machine?

Hello, dear, I am glad to answer for you the size of the clutch spring of Haier XQB60-S12588 washing machine is XQB60-A spring size pro, hello, Haier washing machine XQB60-A clutch spring size, the size is 810 710 88 spring at the bottom of the clutch, first remove the leather Huai empty pulley (clutch) and then remove the plastic gear to see the spring, turn the pulley by hand, if you can't rotate, it is the internal corrosion of the planetary gear stuck Shi Bi, Or the oily copper lining is corroded and stuck between the shaft. When changing, pay attention to the fact that there is a small hook at one end of the spring, hook it into a small hole in the plastic gear, and then screw the plastic gear and the square wire spring back counterclockwise, and tighten the nut.

Do you want to dismantle and clean it yourself? It can't be removed without professional tools, even if you have tools, it is difficult to remove them for a long time, so it is recommended that you find a professional master to take a look.

Hello, thank you for asking the company.

XQS is a dual-power series, the inner barrel needs special tools to disassemble, it is recommended not to operate it yourself, it is best to contact the after-sales service to solve it.

You are welcome to ask the company questions again.

We wish you a happy work life

Disassembly of the inner barrel.

1) Remove the frame and hang the frame at the back of the box (note that the wires and hoses cannot be broken or scratched).

2) Remove the fixing screws of the inner barrel retainer with a Phillips screw screw, and take out the inner barrel retainer.

3) Remove the wave wheel, remove the washer on the wave wheel shaft, and use a special wrench to remove the hexagonal flat nut of the same fixed inner barrel.

4) Gently shake the inner bucket to loosen it, then use it to hold the balance ring and lift it up.

I suggest that you still find a repairman to take a look, our home is also fully automatic, and it may be guaranteed for five years.

Are you a maintenance worker yourself? If you don't send it to the repair shop, you can go to the repair shop to learn.

Remove the screws in the middle of the roller first, carefully pry on both sides of the roller with two flat screwdrivers, if you can't pry it open, you can gently tap the inner shaft with a hammer at the same time (note that the screws must be reinstalled in the middle, but do not tighten tightly).

Sometimes you have to think of other ways if you can't remove it, such as heating it with hot water.

There are two ways to remove the wave wheel, you can try it:

1. Find two bicycle scrap wires, fold one end into a 90-degree straight bend, and then insert the bent steel wire diagonally (180 degrees) into the small hole on the surface of the wave wheel and lift it upward.

2. Find two self-tapping roses diagonally (180 degrees) and screw them into the small hole of the wave wheel, and then use two pliers to clamp the screws upwards and lift them up. The following big nut is the wire, the counter-time direction is loose, the best to disassemble a special sleeve, if there is no 15 wrench can be found a 10 to 12 wrench, with 15 wrenches to adjust to the appropriate card distance straight into the cylinder to jam the big nut, and then use 10 to 12 wrenches to twist the handle of the fifteen wrenches can be disassembled!

That's hard! Generally, it is difficult to remove the clutch from a master who is not a change of job. Even if you remove it and install it badly, the clutch will break down in the short term! If the clutch is broken, it's better to find a professional master to repair it You are in that city, I can help you estimate the market price

This is a bit complicated and useless to remove the wave wheel, the noise is likely to be a problem with the motor or clutch, you tell me the model I can help you judge.

The clutch is broken, and the landlord has a way to change it? Hehe, at least repair it for half a day, or find a professional to repair it for you, hehe (you can buy the clutch back and find someone to replace it).

Hello, thank you for asking the company.

Dear, our national unified service** is 4006 999 999 , please call and our professional service staff will answer for you; Or log in to report your request.

You are welcome to ask the company questions again.

We wish you a happy work life

Haier washing machine XQS80-BJ1218 motor and clutch are connected, can the clutch be replaced separately?

Haier washing machine XQS80-BJ1218 motor and clutch are connected, and the clutch cannot be changed separately. The clutch is located in the flywheel housing between the engine and the gearbox, and the clutch assembly is fixed to the rear plane of the flywheel with screws, and the output shaft of the clutch is the input shaft of the gearbox. During the car's sleepy driving, the driver can press or release the clutch congratulatory pedal as needed to temporarily separate and gradually engage the engine and gearbox.