Who will debug the network connection with the land rover

First of all, you need to change the IP of your local connection to the same network segment as the default IP of the route, such as the internal IP of the route, then the IP of your local connection should be set to, and the last digit 2 can be replaced by 3, 4...255, and then enter the routed in the IE field, or in"Run"It is recommended that you log in with a browser and follow the instructions. Generally, only the DHCP setting of routing (if the DHCP function is disabled, you need to manually set the IP of each host in the LAN) and the protocol settings of the WAN (select PPPOE protocol) and the account and close settings given to you by the ISP.

Click Start Menu >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> &

Open IE and enter in the address If you change the route, you need to change it to the IP you set, enter the username and password to enter the route.

Point guide settings. I choose the next time you use the guide. Refresh a window to come up. You have to turn off the pop-up window settings of Internet assistant and other software

Follow the prompts to set up.

Enter the IP of the router in the address bar, and then enter it to debug it yourself.

Because you have a router, then you need a network cable, just connect the router's LAN to the TV, and then if your router has DHCP turned on, then you don't need to set up IP or anything on the TV.

If your router does not have DHCP turned on, then the IP on the TV is the same as the computer input, remember that the last bit is not the same as the computer, for example, your computer is, then your TV is set.

As for the account and password,You don't need it,That refers to the situation when your TV is directly connected to the broadband cable。

If your computer--routing network cable and cat-routing cable are plugged side by side in the LAN port, which is equivalent to the switch you use, of course you have to dial up.

If you want to access the Internet without dialing, you must enter the username and password into the router, and the modem - the WAN port where the routing line is plugged in, and the computer - the routing line is still the LAN port.

The WAN port of the router is connected to the modem, and the LAN port is connected to the computer.

Set the broadband account password in the router and set it to time-connect pasv chap: it will be automatically disconnected in 5 minutes when the connection is needed.

After a while, the computer will be automatically connected. Turn off the computer for 5 minutes to automatically disconnect the link.

Your network is bound to your network card, of course he can't get on. You go to the official IP address (just enter the IP in the address bar. Username and password to log in.

After letting him bind, you can set the IP to see what the AC is. Then connect to the Internet Protocol locally on his computer. Properties, you should be able to set the IP you get.

You ask the service provider, sometimes he only gives you a use, or you change the physical address to the computer you used before, in the IP change to that computer, it should be OK, I encountered the situation (telecommunications) he locked your sub-account, so you can't use the two computers together, to unlock.

The router has a setup wizard, according to the wizard set up, plug the network cable from the cat or fiber dialer into the WAN port of the router, plug the computer line into any LAN port, turn on the DHCP of the router, and the IP and DNS hooks in the network connection on the computer can be automatically obtained to access the Internet.

Connect the cat's network cable to the WAN port, and connect the computer to the 1,2,3,4 port, of course, the router also needs to set up an Internet account and password.

1. Telecom ** line - Modem provided by Telecom - broadband router WAN interface, broadband router LAN interface - connect two computers respectively.

2. If the telecom directly provides the network port, the telecom network port - broadband router WAN interface, broadband router LAN interface - connect two computers respectively.

1. Connect the modem with the router and the computer separately (this is not simple, find the corresponding socket and put the network cable crystal plug in).

2. The order is the computer continuous router, the router is connected to the modem, if it is connected to two computers, 3 network cables are needed.

3. Turn on the modem and the power of the router, press the reset button of the router, poke a small hole in the router with a toothpick, and look for it carefully, usually next to the power plug.

4. Restart the computer, open IE, and enter a specific IP (this has to be seen according to different manufacturers, there is a product manual, and there are also ** provided on the Internet, dlink:, id seems to be admin, and the password is empty).

5、After that, I entered the settings interface of the router,I guess you didn't succeed in connecting,It's because you didn't enter your adsl and password in the settings interface of the router.,If you don't enter,,It must not be automatically connected.。

Above, I hope it can help you.

It's best to call the telecom company to help you deal with it, after all, they are professional, and some of them are not available on the Internet.

2 ways Because different routers have different settings Enter this ant in the address list: Then click OK to search If what basket password and account number pop up You can directly type: password and account number are admin If you can't get into this, then it proves that your router is going to use another method, or enter it in the address directory:

Ditto! If you can't do it again, you can add me to the shed qq and ask me.

Trouble, chain pickpocketed potatoes thank you!

Follow the instructions to set up the router and fill in your broadband username and password to access the Internet