How do you get started? Ask for advice on how to get started right

You should slow down the clutch at the same time (the clutch is lifted to a certain extent, you will feel that the car is a little started, that is, in a semi-linkage state), and then slightly give the throttle, the car is not easy to turn off, the car goes forward, and then you can lift the clutch, and refuel. Or, you give the throttle a little bit (don't give it too much), then slowly lift the clutch, and the car moves forward, and you lift the clutch all the way up.

Driving to start this problem, you slowly get acquainted with the car. Find a feeling. If you open more, you will naturally start

Hope mine is useful to you.

What's wrong with rookies or not? According to you, you are a rookie. Who doesn't have a rookie time?

When it comes to semi-linkage, the car can go forward, at this time your clutch has not been fully lifted, keep the clutch in this state, and the car will not turn off. Then step on the gas pedal again. When the car gets up and speeds, you can release the clutch completely.

Whether it is a manual transmission or an automatic transmission car, the vehicle must first ignite the engine when starting, step on the clutch to hang a gear, hit the left turn signal, release the clutch, step on the accelerator pedal, start smoothly, and hit the turn signal back after starting on the normal driving lane.

Correct boot order:

1. Turn the ignition key to the second grid, go to the power gear, and let the car computer system start self-test for at least 6 seconds;

2. Press the foot brake and pull the gear from P gear to N gear;

3. Release the foot brake, turn the ignition key to the ignition gear to start the engine;

4. Step on the foot brake, release the handbrake, and pull the gear from N gear to D gear;

5. Slowly release the foot brake and start.

Precautions for starting a manual transmission car

1. Insert the key into the ignition lock, turn on the ignition switch, observe whether the instruments are working normally, and start the engine. If the instrument is not working properly, the engine should be turned off immediately, and the engine can be restarted only after checking and eliminating the fault;

2. Step on the clutch pedal and hang the gear lever into the 1st gear position;

3. Turn on the left turn signal, honk the horn, and observe the front, left and right, above and rearview mirrors of the vehicle at the same time to see if there is any obstacle to starting;

4. Release the handbrake and hold the steering wheel steadily;

5. Gently lift the clutch, slowly lift the left foot up until the clutch is in a semi-clutch state, according to the different induction points of the clutch, the semi-clutch height is different, generally raised between 30-45 degrees, the vehicle begins to vibrate slightly, which means that the vehicle has enough power to start.

Car start-up refers to the transition process of a car from stationary to motion. It is also the first project to learn to drive, and it is the first hurdle that people must pass in driving. A flat start is when a car starts on relatively flat ground.

A ramp start is when a car starts on a ramp or on a relatively uneven road surface.

How do I get started right? The specific steps are as follows:

First, start on a flat road.

Traffic jam and flat road start.

1) Press the clutch pedal with your left foot;

2) The right hand is hung into 1st gear;

3) Turn on the left turn signal with your right hand;

4) Press the horn with your left hand;

5) Release the parking brake lever with your right hand;

8) Release the clutch pedal with the left foot after the car starts;

Second, the ramp starts.

1) Press the clutch pedal with your left foot;

Ramp start. 2) The right hand is hung into 1st gear;

3) Turn on the left turn signal with your right hand;

4) Press the horn with your left hand;

8) Release the clutch pedal with the left foot after the car starts 3-4m;

How can a manual transmission car start fast and without stalling? The old driver teaches you the right way!

Release the handbrake with your right hand and hold down the front of the handbrake, then stretch out the handbrake to completely press down the handbrake and release the handbrake. The left leg slowly stretches out upwards until the clutch is in a semi-clutch state, according to the different sensing points of the clutch, the half-clutch height is different, usually raised by 30-45 degrees in the middle position, the vehicle gradually trembles slightly, which means that the car power is enough.

When driving, it is very important to start, and you must develop the habit of starting in 1st gear, which is good for the car engine, clutch, and gearbox. The operation essentials of the clutch pedal at the start are one fast, two slow, and three linkages.

Correct operation

When the clutch pedal is semi-linked (at this time, the sound of the car engine changes), the speed of the foot pedal extension is slightly slower, and the foot pedal is slowly extended from the linkage to the process of complete cooperation. At the same time when the clutch pedal is extended, gradually press the accelerator pedal according to the size of the car engine's resistance to the land, so that the car can start smoothly.

Before starting the engine, be sure to check that the parking brake handle is pulled up and tightened, and that the gear lever is in neutral or P position. The time of each use of the starter shall not exceed 5 seconds, the interval between the two times shall not be less than 15 seconds, and the engine shall not exceed 3 times in a row.

Generally, when the car starts, it is necessary to step on the accelerator at the same time as the clutch, which can be divided into two types: flat road start and half-hill start.

1. Flat road starting operation

First step on the clutch pedal with the left foot, put the right hand into 1st gear, press the horn with the left hand, release the parking brake lever with the right hand, then slowly lift the clutch pedal with the left foot to semi-linkage, slowly step on the accelerator pedal with the right foot to refuel, let go of the clutch pedal with the left foot after the car starts, and finally refuel with the right foot to speed up to the normal speed, drive the car into the normal lane and turn off the turn signal.

2. Half-slope starting operation

When starting, due to the greater resistance, so the clutch should be more stable than the flat road 3-4 seconds, when you put down the hand brake, do not immediately loosen the clutch, must immediately refuel, and wait for the car to travel slowly 3-4m, and then slowly lift the clutch, so as to ensure that the car starts smoothly on the ramp and does not stall.

To dare to refuel, start uphill, put down the handbrake, immediately refuel, so that the speed of the engine reaches about 1500 rpm, so as to ensure that the car uphill start with sufficient power, there will be no "shaking" phenomenon. The key to a smooth start on a ramp is to coordinate your hands and feet properly, otherwise, it will cause the engine to stall or the car to slip backwards.

Precautions for starting the car

1. Before getting into the car, be sure to look around the vehicle to determine the safety of unhindered driving.

2. When starting, if you feel that the engine power is insufficient and the engine is about to turn off, immediately step on the clutch pedal and start again.

3. The clutch pedal must be carried out according to the essentials of action. If the relaxation is too slow, the contact surface between the clutch friction plate and the pressure plate and the flywheel will wear faster, resulting in damage to the clutch components. The clutch pedal relaxes too quickly. If you press the accelerator pedal too little, it will stall the engine.

4. The refueling of the accelerator pedal should be flexible gradually. Excessive refueling will cause the car to "spasmodic" forward impulse, which not only affects safety, but also damages the transmission parts of the car. When starting, if you can't get into gear once, you can release the clutch pedal once and then hang it, or try to hang other gears first, and then hang the starting gear.

5. After the car starts, it is not allowed to turn the steering wheel immediately and drive into the road, and it should gradually enter after confirming the safety.

Starting is one of the basic skills that drivers must master when driving a vehicle, and the correct starting operation can ensure a smooth start and ensure safe driving. The following will introduce the specific operation steps of starting the car.

Adjust the seat position and mirrors.

Before starting, the driver needs to adjust the seat position and mirrors to ensure that they are seated comfortably and have a clear view of the vehicle.

Press the clutch.

Stepping on the clutch is the first step in getting the car started, and the clutch is used to disengage the engine from the transmission. While depressing the clutch, the brake pedal needs to be pressed to prevent the vehicle from slipping.

Gear. After pressing the clutch and brake pedals, the gear needs to be adjusted from neutral to first gear. When shifting gears, you need to make sure that you are in the correct gear to avoid danger.

Release the handbrake. Before the car starts, you also need to release the handbrake so that the vehicle can slide freely.

Release the clutch and brake pedal.

When the above steps are completed, the clutch and brake pedal need to be released slowly. It needs to be done slowly and evenly when releasing the clutch and brake pedal to ensure a smooth start of the vehicle.

When the clutch and brake pedal are fully released, proper throttle is required to ensure that the engine can propel the vehicle forward smoothly. The force of the accelerator pedal needs to be adjusted according to the road conditions and speed to avoid overspeeding or erratic driving.

Shift gears correctly. When the vehicle is moving, it is necessary to change the speed according to the speed of the vehicle and the road conditions. When shifting, you need to first press the clutch, then shift to the next or previous gear, and finally release the clutch slowly.

When shifting gears, it is necessary to pay attention to the accuracy and smoothness of the gear to ensure the smooth and safe driving of the vehicle.

In short, starting the car is a basic skill that the driver must master, and the correct starting operation can ensure a smooth start of the vehicle and ensure the safety of driving. It should be noted that you need to pay attention to the situation around the vehicle at all times during starting and driving, and maintain a high level of vigilance and caution.

1. Adjust the seat before driving to ensure that your feet can step on the clutch, brake and accelerator more firmly and comfortably. For manual transmission cars, when starting to hang up the first gear, the clutch should be pressed to the end, and the right rough slide foot is put on the accelerator to prepare.

2. When starting to start, the clutch of the left foot is slowly lifted to nearly half, when you feel that the vehicle is shaking, you will release the handbrake in time, and then gently click the accelerator, and slowly release the clutch when the car wants to move forward, and then add a little throttle to start successfully.

3. If you are a novice at the start of the ramp, you should pay special attention, if you release the handbrake quickly, and the clutch is not lifted in place, it is easy to slip. The best way to do this is to press the clutch and brake when starting, and the handbrake can be used or not. Release the brake when the clutch is halfway up, at this time the vehicle is in a semi-clutch state, the car will not slip back, and at the same time let the limb add the throttle, slowly release the clutch, and the start is successful.