Tianlang audio wiring problem, what wire does Tianlang audio use to connect to the power amplifier

This has nothing to do with the speaker, it's a problem with your microphone input and the microphone pre-amplification circuit. It is possible that there is a microphone with a pre-amplified output that only one channel enters the amplifier circuit, resulting in another microphone-free sound output.

It's simple: turn the left and right (L, R) balance knobs on the microphone on the mixer to the middle position, and both speakers will ring.

The microphone input of the mixer is not adjusted well, and some inputs have adjusted the left and right balance, high and low bass, reverb, etc., which should be readjusted to the ideal state.

I guess your mixer isn't tuned properly. According to what you said, when one microphone said, only one speaker sounded, and the other had no sound, which is not the problem of turning off the speaker wiring, is that the knob that adjusts the balance between the left and right in the set of modulation knobs connected to the microphone on your mixer is twisted to the side, just twist it to the middle position. Try!

Hope it helps.

It seems that the audio is not mono--- it is not mono when looking at the amplifier.

It depends on whether you are a two-line crossover or a merger, and the effect is much worse.

I'll take one step in place, whether the microphone is controlled in 2 ways, that is, it is controlled by several faders from the mixer, and I find a bal is the balance of the knob and hit it in the middle It's OK Both speakers rang.

Your microphone must be connected to the mixer, and see if the channel balance of the microphone in question is not placed in the middle position, and it may be that only one channel is selected.

It should be a problem with the settings of the mixer, if you swap the two speakers, if the original speaker that does not sound still does not sound, it may be a problem with the speaker.

First look at the channel where your mixer feeds the microphone signal, there will be a knob (l r) above the fader to center it, and then see where the output of that channel is, whether it is programmed or not.

If you have money, it is best to use pure monocrystalline silver wire.

Of course, the connection is corresponding.

Speakers!

The loudspeaker with four binding posts provides the user with a "bi-wire" connection, which uses two sets of wires to transmit the high-frequency and low-frequency components of the power signal, and the two sets of wires are still connected at the output end of the amplifier. If you do not use the two-wire crossover connection, you can use the two short-circuit tabs configured by the speaker to connect the upper and lower binding posts separately, and only one set of wires can be connected to the power amplifier.

Hello, please wait.

The wiring method of the 4 binding posts of the speaker is the same as that of ordinary audio, there is no difference, and there are corresponding logos on the machine, just connect the corresponding speaker according to the identification. Tools required: Peeling pliers, scissorsMaterials:

Wire, speaker, amplifier speaker 4 binding post wiring method steps: 1First of all, the four wires of the two speakers are head shaped, the end of the wire is peeled one centimeter and cut with scissors for later use; 2.

Connect the black wire of the two wires marked with the word L on the speaker or the wire marked with the minus sign to the terminal marked with the minus sign (-) on the left side of the four terminals of the power amplifier; 3.Connect the red wire of the two wires marked with the word L on the speaker or the wire marked with the plus sign to the terminal marked with the plus sign (+) on the left side of the four terminals of the amplifier; 4.Connect the black wire of the two wires marked with the word R on the speaker or the wire marked with the minus sign to the terminal marked with the minus sign (-) on the right side of the four terminals of the power amplifier; 5.

Connect the red wire of the two wires marked with the word R on the speaker or the wire marked with the plus sign to the terminal marked with the plus sign (+) on the right side of the four terminals of the power amplifier; Note: The speaker wiring must be connected to a positive pole and a negative pole for each speaker, and two wires of a speaker cannot be connected to two positive poles or two negative poles at the same time. Civilian speakers do not have a bridging function, and the power of the speaker may not meet the bridging function, so it is not recommended to connect in this way.

Questions. <>

Two lines of the main line.

Uh-huh, isn't this on the street.

yes, that's what you said. Generally, the power amplifier uses a lotus head, and it is OK to buy an adapter cable for turning an inch head to a lotus head.

That's right, just this program. But your stuff is big enough, probably no smaller than a computer, hehe.

Is it a docking of independent speakers and independent amplifiers? Two speakers one after another as long as they are not short-connected to the power amplifier output, generally according to the standard is adjacent red and Lingyuan black as a group. Generally, the power amplifier adopts the voltage negative feedback mode, that is, the output ruler is in a slow state, which group uses a "ground", so there is a "ground" in each speaker line, and they are connected.

The power meter resistance is approximately "0", and the power amplifier output with negative current feedback is independent and cannot be grounded.

The vast majority of Tianlang boxes are so air-resistant,There are connecting bridges when leaving the factory,Just connect the corresponding color,That is, the red of the red power amplifier,If your power amplifier supports two-wire crossover,You can first remove the Cong Jing connection bridge,The tweeter output of the power amplifier is connected to the speaker above two,The bass Chang Zheng blind output is connected to the speaker below the two,

The 4 terminals are played with two-wire crossover, which depends on whether your amplifier has this function or not.

The ordinary connection method is that one pair of terminals can be connected, and the other pair of liquid shoot terminals should have metal pieces infiltrated and buried on the front pair of terminals.

4 terminals, 2 red, 2 black, one stereo, one red and one black, you can...

It's strange, I've been doing professional audio for almost 10 years, and I've never heard of a head called Oh, I only know that the weak signal has XLR head (XLR head 2+3-1 grounding answer), two-core head (middle indirect positive, side negative) and three-core head, etc.

I call Bell head the most used for professional speakers,I don't know what you call it,This connector is divided into1+1-,2+2-,4 feet。

99% of the speakers on the market are connected to the two pins of 1+ and 1-, and if you want to be safe, put 1+ and 2+ together and 2+ together.

Normally we take 1+1-. In some special cases, 2+2- will be used. For example, the British Tianlang box is connected to 2+2-.

To be on the safe side, you connect 1+ and 2+, 1- and 2- as the 1st floor says. This way, no matter what kind of solution the box is, it can make the box ring.