Broadband wiring problem 100, broadband wiring problem

It is estimated that your first floor**and the third floor** are not the same number, if it is not the same number, it is not possible to access the network, the correct connection is: the network cable pulled from the cat on the first floor must be connected to the router WAN port, any of the 4 100 Gigabit LAN ports are wired to your computer on the first floor, and the next step is the debugging of the router, enter it in the IE browser, user name: admin password:

admin enters the tp-link setting interface, clicks next in the setup wizard, clicks to select pppoe mode, enters your username and password, (that is, the username and password of your computer dial-up Internet access) and clicks to complete, and then pulls any of the 4 100 Gigabit LAN from the router to the third floor to connect to the computer, and you can directly access the Internet without dialing, at this time, you must delete the dial-up Internet access in your computer on the first floor from the online neighbors, so that your computer on the first floor can also access the Internet at the same time. It's okay, just steal the fun.

Isn't it the same ** box connected to the wire? The current ADSL is bound to the port to find a service provider.

Most likely a problem with your separator, your current separator should be installed at the inlet end on the first floor. The separator separates the high-frequency and low-frequency signals. You are on the first floor is separated out of the low frequency can access the Internet normally.

Upstairs is separated out of the high frequencies and can only be used for use**. So the separator should be installed on the third floor, and one is separated for Internet access, and the other is used for **.

Take a look at the voice splitter, it's a small box, the one that separates the ** and adsl lines, some cats can't do it, or use two to put one on the first floor, and one on the second floor.

That is to say, you are not allowed to have a ** machine in front of the separator on the Internet, and if you have one, you must use a voice separator.

For reasons why the distance is too large, you can add a switch in the middle.

The line on the third floor may not work.

Maybe you didn't get the separator cord right! ~~

If you want to replace the original thread and replace it with a long one, you do this:

Remember to remove the end of the wire, now I'll name him the wire number, and that's where your new wire is connected. You can connect your new wire, the new wire is 4 cores, you take two red and green wires, red or can be. If it is a two-core wire, either one can be connected, and the other can be connected.

If you are growing the line on the original line, you do this:

Remember the end of the original line, now I'll name it the wire number, and that's where your new line is connected. You can connect your new wire, the new wire is 4 cores, you take two red and green wires, red or can be. If it is a two-core wire, either one can be connected, and the other can be connected.

Thank you for your question.

Directly on. There is no positive or negative line on that line, so sit down and test it with **; **No, just swap the colors.

The outside line should be a ** line, you can pick it up yourself, buy some ** line and pick it up yourself, when you buy a ** line, let people help you pick up a ** crystal head at one end, and then connect it to your cat.

To connect a crystal head, buy a small crystal head junction box to lengthen the network cable.

When applying for ADSL, the network chamber of commerce will provide you with a similar one-to-two adapter, and you must use this to divert, one to connect to the computer, and one to the **.

**Noise problem is mainly caused by ADSL's electromagnetic interference,**There are generally two **wire jacks on the machine, use one, leave one, buy another one to the hardware and electricity**, insert one end**, and cut the crystal head at the other end, deliberately leak a metal wire, connected to the ground, so that there is a circuit and try again, it should be possible.

Network problem: Because only one network is opened at the same time, the same line cannot be connected to two computers at the same time. You can buy a home router in the computer market, ** at about 100 yuan, connect the network cable of the ADSL computer to the router, and then connect the network cable from the router to different computers. Generally, home routers have one input port and four output ports.