Can 1060 aluminum plate be replaced with LY12

It can be replaced, but the cost of ly12 is much higher than that of 1060 aluminum plate, which is not cost-effective.

LY12 is the old grade, the new grade is 2A12, which is a high-strength duralumin, which can be strengthened by heat treatment, has medium plasticity in the annealed and just quenched state, good weldability by spot welding, and has a tendency to form intergranular cracks when welding with gas welding and argon arc welding; The machinability of the alloy is good after quenching and cold work hardening, and the machinability is low after annealing. The corrosion resistance is not high, and anodizing and painting methods are often used to improve its corrosion resistance.

1060 aluminum plate is widely used in products that do not require high strength. Products are commonly used in signboards, billboards, building exterior decoration, bus bodies, high-rise buildings and factory wall decoration, kitchen sinks, lamp holders, fan blades, electronic parts, chemical instruments, sheet processing parts, deep-drawn or spinning concave utensils, welding parts, heat exchangers, clock surfaces and plates, nameplates, kitchen utensils, decorations, reflective appliances, etc.

In general, it is not possible, because the difference between the two is relatively far, the composition is different, the properties (hardness, tensile strength, elongation) are not the same, and the oxidation effect and conductivity are different.

1060 is pure aluminum, which represents pure aluminum with aluminum content; LY12 is now called 2A12 (also called 2024) and is alloy aluminum.

If you want to use an alternative, it is recommended to use 1050 (pure aluminum with aluminum content) or 1070 (pure aluminum with aluminum content).

At the same time, pay attention to the state of the aluminum plate (there are H14, H18, H22, H24, H26, H32, etc.).

It is best to use 1050 or 1070 in the same state instead of 1060 in the same state, so that the performance and other properties are not much different.

1060 is a series of pure aluminum, LY12 is also 2A12, which is a high-strength duralumin, which may not be replaced by different uses.

1060 is less expensive than LY12.

Boss: Can tofu be replaced with bricks?

Summary. Then there is the aluminum plate use.

Aluminum plates are widely used in products that do not require high strength. Products are commonly used in signboards, billboards, building exterior decoration, bus bodies, high-rise buildings and factory wall decoration, kitchen sinks, lamp holders, fan blades, electronic parts, chemical instruments, sheet processing parts, deep-drawn or spinning concave utensils, welding parts, heat exchangers, clock surfaces and plates, nameplates, kitchen utensils, decorations, reflective appliances, etc.

Aluminum plate requires a variety of industrial structural parts with certain strength, weldability and high corrosion resistance, such as manufacturing trucks, hitching buildings, ships, trams, furniture, mechanical parts, precision machining, and a wide range of industrial materials.

What is the difference between aluminum plate 1060 and 6061.

Hello! I'm a friend of you, please wait a while, I'm sorting out the answers! We hope you understand! Thank you! ☺️

Hello! Aluminum plate 1060 and 6061 are first of all the alloy differences Aluminum plate is pure aluminum plate, and the purity can reach the above.

Because it does not contain other technical elements, the production process is relatively single, and it is the most commonly used series in the conventional industry at present.

Then there is the use of aluminum plate Aluminum plate is widely used in products that do not require high strength. Products are often used in signboards, billboards, building exterior decoration, bus bodies, high-rise buildings and factory wall decoration, kitchen sinks, lamp holders, fan blades, electronic parts, chemical instruments, sheet processing parts, deep-drawn or spinning concave utensils, welding parts, heat exchangers, clock surfaces and plates, nameplates, kitchen utensils, decorations, reflective appliances, etc. Precision machining, industrial materials are more extensive, etc.

Finally, the difference between aluminum plate is pure aluminum plate, the production process is relatively simple, and the aluminum plate is aluminum alloy plate, the production process is complex, and it is expensive.

Hope it helps! I wish you a happy life! All the best! Be in good health! <>

<> than the heart] [than the heart] [than the heart] [than the heart] [than the heart].

1060 is a grade that represents the alloy composition and can be considered aluminum.

H14 is the heat treatment state of the aluminum alloy, and the same alloy composition is different in the heat treatment state, and its mechanical properties are different.

1060 aluminum plate, also known as pure aluminum plate, belongs to a commonly used series in the aluminum strip family. The advantages of this series of aluminum plates: the most commonly used series, the production process is relatively single, the technology is relatively mature, and it has great advantages compared with other high-grade alloy aluminum plates.

It has good elongation and tensile strength, and can fully meet the conventional processing requirements (stamping, drawing) with high formability.

Reference: National standard for aluminum strip (GB T 3880-2008) If you have any questions, please ask, I hope it can help you.

1060 aluminum plate is also known as pure aluminum plate with aluminum content, which is a commonly used series in the aluminum strip family. 1060 aluminum plate belongs to industrial pure aluminum, which has high plasticity, corrosion resistance, electrical conductivity and thermal conductivity, but low strength, heat treatment can not be strengthened, and machinability is not good; It can be gas welded, hydrogen atom welding and contact welding, and it is not easy to braze; It is easy to withstand all kinds of pressure processing, extension and bending.

The difference between 1060 aluminum plate and 2A12 can be considered from the following two aspects:

First, the chemical composition of the two is different:

Chemical composition of A12 aluminum plate: magnesium mg:; Zinc zn: ; Manganese mn:; Titanium ti: ; Nickel Ni: ; Iron Fe: ; Iron + nickel Fe + Ni:.

Chemical composition of aluminum plate: silicon si:; Iron Fe: ; Copper cu:; Manganese mn:; Magnesium mg:; Chromium cr:; Zinc zn: ; Titanium ti: ; Aluminum AL: Margin.

Second, the use of the two is different:

The use of A12 aluminum plate: aircraft structure (skin, skeleton, rib, partition, etc.), rivets, missile components, truck wheels, propeller elements and other structural parts.

The use of aluminum plate: various industrial structural parts that require certain strength, weldability and high corrosion resistance, such as manufacturing trucks, hitchhiker buildings, ships, trams, furniture, mechanical parts, precision machining, and a wide range of industrial materials.

However, there is a big difference between the two in terms of hardness and application range, among which the hard repentance of 1060 aluminum plate is low, the hardness of LF12 aluminum plate is high, and the LF12 aluminum plate can be anodized, and the ** is also 5052 aluminum plate** high. In the alloy content, 1060 aluminum plate belongs to pure aluminum plate, with high aluminum content, so the ductility and conductive heat dissipation performance are relatively good, while the magnesium alloy content of LF12 aluminum plate is high, with good corrosion resistance and high strength, so users should choose the appropriate aluminum plate material according to actual needs.

And 1060 are pure aluminum plates, the aluminum content is different, generally the higher the aluminum content, the aluminum plate is relatively softer, so 1200 aluminum plate is a little harder than 1060 aluminum plate The tensile strength is higher than 1060.

1060 aluminum plate belongs to industrial pure aluminum, which has high plasticity, corrosion resistance, electrical conductivity and thermal conductivity, but low strength, heat treatment can not be strengthened, and machinability is not good; It can be gas welded, hydrogen atom welding and contact welding, and it is not easy to braze; It is easy to withstand all kinds of pressure processing, drawing and bending. 1060 aluminum plate is widely used in products that do not require high strength. Products are commonly used in signboards, billboards, building exterior decoration, bus bodies, high-rise buildings and factory wall decoration, kitchen sinks, lamp holders, fan blades, electronic parts, chemical instruments, sheet processing parts, deep-drawn or spinning concave utensils, welding parts, heat exchangers, clock surfaces and plates, nameplates, kitchen utensils, decorations, reflective appliances, etc.

The main alloying elements in alloy 6061 are magnesium and silicon, which have medium strength, good corrosion resistance, weldability, and good oxidation effect, and are widely used in various industrial structural parts that require certain strength and high antimicrobial corrosion. It is an Al-Mg-Si alloy with medium strength, good plasticity and excellent corrosion resistance. In particular, it has no tendency to crack with stress corrosion, and its weldability is excellent, and it has good corrosion resistance and cold workability, and it is a wide range of applications.

Promising alloy. It can be anodized and colored, and can also be painted with enamel, which is suitable for building decoration materials.

6061 Aluminum Plate Specifications:

6061 plate spot specifications: thickness).

6061 bar stock specifications: diameter).

6061 wire stock specifications: wire diameter).

For details, please consult Changsheng Aluminum. Hope it helps.

1060 is a series 1 industrial pure aluminum, with an aluminum content of more than 99%, because the aluminum content is high, and the hardness is slightly softer. 6061 is a series 6 aluminum-magnesium-silicon alloy aluminum, which has a higher hardness than 1060 due to the addition of other elements of the metal.