Regarding the serious error after the computer is turned on, is it a motherboard problem?

Let's talk about a simple shop.

An unknown hard error is usually caused by damage to unknown hardware.

You said that the windows reading bar is normal after you boot it.,I judge that there is no big problem with the memory.,And then the blue screen should have entered the system.,Then there shouldn't be a problem with the motherboard.,Or it's impossible to burn it.,The burned board can't run to that point.。 As for the hard drive, sometimes a small part of the bad sector can still be run.

Speculation: There may be a problem with the CPU fan that is not running well and the CPU temperature is too high.

Some bad sectors of the hard disk cause the machine to stop during operation

The above statement is based on empirical analysis, of course, it is impossible to experience everything personally.

Suggestion: Your brother is willing to spend 1600 with a 160g hard drive, and you'd better spend another 200 yuan to get a 160g hard disk.

stop:c0000218 registry failed to load hive (file): systemroot system32 config software or its logs or alternate data.

This error occurs when the computer restarts, after Windows XP has copied the installation files to the hard disk.

Cause This issue can occur if any of the following conditions are met: The hard drive you use to install Windows XP might not be compatible with Windows XP.

The hard drive you used to install Windows XP may be corrupted.

1: Make sure your hard drive is compatible with Windows XP.

2: Use the Failback Console to confirm that your hard drive or file system is not corrupted.

Important: Microsoft only recommends that power users or administrators use the Failback Console.

Note: Only the administrator account can access the Failback Console. 1.Start your computer from the Windows XP disc. If prompted, select any option that you have to choose to boot your computer from a disc.

Note: To boot a computer from a Windows XP disc, the CD-ROM or ***-ROM drive must be configured accordingly. For information about how to configure your computer to boot from a CD-ROM or ***-ROM drive, refer to the documentation that came with your computer or contact your computer manufacturer.

2.When prompted to select Repair or Failback, press R. This will launch the Microsoft Failback Console.

3.When prompted, type your administrator password. If the administrator password is empty, press Enter.

4.Use the chkdsk command-line tool to check the hard drive. At the command prompt, type chkdsk r, and then press Enter.

5.Read the resulting information and then follow all the steps you have to take to complete the process. For example, you may be prompted to run chkdsk f to resolve certain issues.

6.Restart your computer and try running the installer again.

3: Replace the hard disk.

If the hard drive is corrupted and cannot be repaired, you may have to replace it. For information on how to replace your hard drive, contact your computer manufacturer, your computer's retailer, or a qualified service technician.

Know the answer.

I have ever encountered this situation with a notebook, and it should be a problem with the motherboard. Is the hard drive parallel or serial? If it's a parallel mouth, your brother will definitely be deceived. Go find that guy.

Old hard drive?.The system is reinstalled.

Boot prompt: Press the trace mode F1 to process experience, and the interface prompts to press F1 or F2.

1. When this interface appears, you can start the computer by pressing F1 directly. After entering the attitude relaxation system, see if the system time is correct, if the date time is not the current time (it will generally become the time when the motherboard leaves the factory). At this time, turn off the computer, unplug the power cord, and replace the motherboard battery.

Turn on the machine and press F1 to enter the system and modify the time. This is due to low motherboard battery. If you replace the battery and change the time, you will still see this prompt (time back to the factory state) after restarting (after a while).

It is most likely that the motherboard is damaged, the motherboard battery is not powering the BIOS chip, or the BIOS chip is damaged.

When the time is no problem after entering the system, restart the computer and enter the BIOS (desktops generally press the delete key, notebooks generally press F2, F12) to set up the interface to see:

Here we take AwardBIOS as an example (different versions vary). After entering the BIOS, select the first item "Standard CMOS Features" and press Enter (as shown in the picture above).

In the new interface, find the following two items, drive A and drive b, all set to "none", that is, there is no floppy drive.

2. The solution is as follows: (1) Press F8 all the time when you boot up, select the last correct configuration, and see if you can enter the system. (2) If not, unplug the memory module, plug it back in, or clean the computer and restart it.

3) Use a USB flash drive to make a boot tool, use diskgenius to detect whether there are bad sectors on the hard disk, fix the bad sectors, and restart the computer. (4) Reinstall the system with a system CD. Here's how:

Preparation: A CD-ROM of the Shooting System. 1. Insert the disc first, press delete (F12, F2, F9, slightly different according to different computers) to enter the BOIS settings after booting, set the first boot device to cd *** (or the item with CD ***) in the boot item, and press F10 to save.

2. Enter the system installation interface, and select one key to install the system to the C drive. Note: If the system is not reinstalled by partition, all the data on the C disk will be emptied, and the data on other disks will be there; The partition reloads the system, and all disks are emptied.

Hello, there is a problem with the power supply, and the white screen prompts that the time setting is incorrect, and the power supply IC should be faulty.

It may be that the battery is insufficient and needs to be charged in time, after plugging and unplugging the power supply, click the Continue option below to enter the start interface.

After updating the motherboard, there is a problem with the desktop:

After updating the motherboard and hard disk, the computer must re-install the system.

The relationship between the motherboard, the hard disk, and the system is: the system is installed in the hard disk, and the system detects the motherboard environment during installation, and the system installation is completed according to the environmental conditions of the hail motherboard.

Now if you want to migrate the hard drive to an unfamiliar motherboard, it doesn't recognize it, and there is a strange problem. Some or simply don't start.

Resolved: Reinstall the system in a new motherboard environment.

If you change the motherboard, the mouse and keyboard are not used in a way, and you are not able to connect to the network, then it is likely that your motherboard is asking the dust problem, because your computer can be turned on normally, but the mouse and keyboard can not be used, which should be caused by the motherboard problem.

If you suspect that there is a problem with the installed operating system itself, or that it does not match, it is recommended to reinstall the operating system, and check whether the remaining drivers are installed, and then test the machine.

After replacing the motherboard, you need to reinstall the system, otherwise, unless the two motherboards are of the same model, there will be a system failure.

It's clear that the hardware is loose.

It is recommended to remove the hardware and put it back on!

There is a problem with the motherboard, why does the control panel freeze when it is opened?

I guess it's a problem with the system, try to reinstall it?

There is no good way but to replace it with a new one!