If the mouse micro movement is broken, do you want to change both sides together?

This problem depends on yourself, first of all, you have to remove the foot sticker basically to remove the mouse, the viscosity of the foot paste is not enough after the foot sticker is removed, and you have to change the foot sticker, so you have to change the foot sticker once you dismantle it, from an economic point of view, one time to change two micro motion saves the trouble of disassembly and assembly and the cost of the foot sticker, although the foot sticker is not expensive.

There is also the use of the aspect, if the two micro movements are not a brand model, the strength is not the same, and it will be awkward to use, even if it is a brand model, there will be differences between the old and the new because of the service life, so it is generally recommended to change the two together, and the micro movement is not expensive, a few dollars a piece.

If one side of the mouse's micro-movement is broken, it must be replaced on both sides, because it is matched.

No, you just need to change the bad side, there is no need to change both sides at the same time.

This is not needed, if one side is broken, it is enough to replace the one side.

If the mouse micro-movement is broken, of course, both sides must be replaced together, otherwise it is not good to use asymmetrically.

Hello, it's better to use this mouse together, replace it, and replace it with a new one, and it's better to match.

Generally, this kind of change is changed on both sides together.

Because the two sides are originally matched, if you only change one side, it will cause poor performance and mismatch, so it is best to change both sides together.

If the mouse is only a little broken, you want to change it unilaterally, but the mouse is not very expensive, so it is better to replace it entirely. One side was changed and the other side was broken.

In fact, I don't think you need to change all sides to normal, but if your mouse is not very expensive, I think you might as well change it to a new one.

Under normal circumstances, because its induction is connected, so this situation must be changed on both sides, otherwise there is no way.

This is just the bad one, you don't need to replace the good one, it's not necessary.

Do you need to change both sides of the mouse for a year? Normal don't change both sides together, you don't change you.

If the mouse is broken, but you have to replace the whole mouse, F4 has to be replaced with other things, because the mouse is not expensive.

The (mouse properties) on the control panel can be used interchangeably with the left and right buttons!

I think you can ask about this place where you buy retail parts, and they'll tell you about it.

It's best to suggest that you change both sides together!

If you have a bad stomach, you can check the Internet to find out how to solve it.

The mouse's micro-movements are interchangeable, but is it necessary? If one of them is broken, it will not work properly if you change it to the other direction.

Don't be afraid of trouble, you can use an electric soldering iron to change, and it may cause both micro-movements to be damaged by heat.

Hello:——1. The micro switch of the mouse is completely replaceable.

2. The micro switch of the left and right buttons of the mouse is the same, and the switches of different mice can also be replaced. The soldering time should be fast to prevent burning the circuit board.

Yes, it is called to switch between the primary and secondary buttons. Control Panel - Hardware & Sound - Mouse.

You can repair it yourself, I don't know what kind of mouse yours is, if it's a game mouse to buy a hundred, it can be repaired by yourself.

1.Buy a small welding gun on a treasure.

2.Or buy a mouse micro-movement on a certain treasure, start according to your own feel, there are light and heavy 3Once the accessories are in hand, you can repair them yourself.

If you have strong hands-on ability, you can change the micro-movement by yourself, and if you have poor hands-on ability, you can also find a computer repair point to replace it.

First of all, you need to use a hair dryer to heat the mouse footpad, the purpose of heating is to make the adhesive behind the mouse foot pad soften, so that in the next step, we can easily remove the mouse footpad, the heating time is about 1 2 minutes, you can feel hot when you touch the mouse foot pad with your hand, and you can stop heating when there is a slight plastic smell;

After the heating is stopped, you can use a treated plastic card (gift cards and other plastic cards, use scissors to thin the edges of them) and insert them firmly down along the edge of the mouse footpad, trying to avoid inserting the footpad into the position between the footpad and the gel, causing the footpad to separate from the adhesive. After insertion, use the blade-shaped part processed on the card to cut upwards at a small angle, while separating the foot pad from the mouse chassis, keep the flatness of the foot pad as much as possible to avoid deformation caused by hard pulling;

Be careful when separating the mouse cover from the chassis, because there are a lot of wires between the mouse cover and the chassis, and if you break it, the mouse will look good. In fact, these cables are easy to handle, and they can be removed from the socket of the mouse's motherboard using tweezers or small tip pliers. In addition, it should be noted that the two small sockets on the left side of the mouse motherboard are arranged according to the left red and right black.

After the mouse motherboard is removed from the chassis, we can start to replace the micro-motion of the mouse with problems (generally in order to consider the consistency of the feel, the two micro-movements are replaced at the same time);

Use a soldering iron to melt the tin on the faulty mouse micro-motion pins, and then use a solder suction device to suck it all away, and after all the tin on the three pins is cleaned, the mouse micro-motion can be removed with a slight press;

Clean up the remaining tin in the mouse micro soldering hole, insert the new micro motion in the direction marked on the circuit board (keep the micro motion contact direction consistent with the contact direction shown in the motherboard diagram), you can use solder to solder the new micro motion on the replacement side, and try your best to keep the micro motion in close contact with the mouse motherboard when toldering to avoid gaps that cause the mouse button travel to become shorter. When soldering the pins, all the solder should be melted to avoid the problem of virtual soldering (that is, the solder is melted unevenly, resulting in the pins not being fully connected with the pad as a whole);

After replacing the micro-motion, touch the micro-motion contact with your hand to conclude that the problem of the loose right mouse button has been completely solved, and then the installation can be completed in reverse order.

As long as you know how to use a soldering iron, you can do it.

If you've never used it or don't work with it, don't try to replace it yourself.

Integrated circuit boards are no better than exercise boards. After a long soldering time, it is easy to burn out nearby components or burn off the copper sheet. Resulting in the scrapping of the entire board.

Now the mouse is only sold for about 10 yuan on the market. Buy a new mouse. If you really want to repair it, you can still find a repair computer to help you change the button.

1: The problem is generally the contact in the red box, take a closer look and you can see that there is a layer of black on the surface of the contact, that is, the thing plays a resistive role on the contact surface of the contact and the copper sheet, and it is OK to eliminate the black thing with sandpaper.

2: It may also be that the micro switch inside is broken. Buy a switch element and replace it, or swap the switch between the left button and the middle button, because the middle one is not commonly used.

Not a mouse issue. You go to the control panel and set up the mouse.

My viper has been repaired three times. The mouse looks at the feel. If it's broken, either replace it with the same one or fix it.