After Tietong dials up the Internet, the router cannot share the Internet

You're a very puzzling question.,Just ask to connect to the land game to share the Internet,It's strange if you can do it.,Your cat (that is, the so-called switch you said) should be a line and ** line.,I guess this is what you call the dial-up line.,The other one is to connect to the PC and you now do what I say (provided that you go to the land game setup interface):

Connect the original cat and the computer directly to the WAN port of the land game you bought, so that there are only 4 ports left on the land game, you take a line in the remaining mouth to find an open mouth and plug in the other side to connect the computer, at this time you open the computer into the land game, set up the wizard--- next step--- adsl virtual dialing (PPPoe) - the next step --- enter your password --- complete, wait a few seconds for you to open the web page and you will see it, If you add a computer to the Internet, you will be wiring out on the remaining port, which is the correct way to connect Lu You, and you are wrong。。

How can the router settings not get in, there is a default factory username and password on the back of the router, press and hold the resert key of the router with a needle for about 10 seconds, and the router will be reset, or press and hold the reset button when the power is off, and release the reset button after about 10 seconds of power-on.

You'll need to go into the router's settings. Because there is no dialing and running in it, it can't be connected. You can take a look at the instructions of the ASUS router and follow along!

Connect the dial-up line to the switch, connect the network cable to the other hole of the switch to connect the router, and connect the network cable to the other hole to connect the router.

The router is generally not 4 holes, confirm that there is no problem with the 3 ports mentioned above.

If the computer can be used, there should be no problem with the basic settings and quality of the router;

The mobile phone used to be available, but suddenly it was unusable, and it was suspected that the router had been hacked and the wireless access password had been changed;

Here's how you can do it:

Unplug the power of the router, find a paper clip or a thin stick such as an ear picker, there is a small hole near the power jack of the router, insert the thin stick you found into the small hole and hold the button inside and don't let go, connect the router to the power supply, wait a few seconds, observe the row of small lights on the front panel of the router start to flash, let go --- the router has restored to its factory value;

Re-set the password according to the router manual, and it is best to set the wireless password at the same time, so that the phone can go online again;

One question to note: if the router wireless access password changes, you need to delete the original AP (access point) in the mobile phone, scan it again to get this access point--- reconnect again--- prompt you to enter the password--- enter a new password, I wish you a good time :)

Try changing your wireless router mode to:

Non-automatic auto

Try again.

My home is also Tietong broadband, since the computer can be accessed, the network is no problem, and the probability of router problems is also very small. See if it's a problem with your phone's settings. If the phone settings are fine, it may be a compatibility issue between the phone and the router. Only one of them can be swapped out.

It seems that Tietong is forbidden to route.

If your router cannot be connected to the network after setting, please log in to the router interface, click "Advanced Settings" - "System Status" to check the WAN status and connection status, please check the following troubleshooting methods according to the router WAN connection status:

It's very simple, you call Tietong customer service, and you say, "I changed a computer, please swipe my number." It must do what I told you, and then it's OK. Tietong's server is bound to the network card address, so every time you change computers or routes, you have to swipe the number.

The WAN port is used to connect the modem to the router, and the MAC address of the route is cloned.

WFDLTS is right, Tietong lock address.

After a month of exploration, I finally solved this kind of problem, the reason for this problem is that the crystal head from the computer room to my own computer should use the parallel connection method, not the cross connection method.

After the crystal head is changed, dial up with any computer first, and the connection is successful. Then use the router to connect (at this time, if the MAC address is restricted by the operator, it must be unable to connect) The solution is: open the router settings page (i.e.:

Write or complete your account password in the IE or in the setup wizard, then open the right rail: Network Parameters - MAC address cloning, clone the MAC address, and wait for a few seconds for the router to restart automatically.

Restart the computer and the connection is successful.

I'm the same ... But the connection is normal.。。。 The company's maintenance is also coming... Still didn't do it well、、、 died in a hurry.

Change the IP of the router without changing the computer's try.