Fiber Dial up Internet How to set up a router

It's all the same, you take the optical fiber cat to borrow the WAN excuse to follow the line to the router on the computer to set up, and follow the wizard to enter the dial-up account password. If you have a question, thank you.

Here's how to set it up:First, after factory setting the router, enter "Enter" in the browser, as shown in the figure below

2. Then enter the factory password in the window, as shown in the following figure:

3. Then click on the "Internet Settings" option in the window, as shown in the figure below

4. Then select the "Broadband Dial-up Internet" option in the box, as shown in the following figure:

5. Finally, enter the broadband password in the window, as shown in the following figure:

Restore the router to factory settings, connect the computer to the router with a network cable, open a browser, enter the address, username and password, and then set up the router.

Steps: Power on the router and unplug all network cables on the router.

Factory reset the router: There is a 'reset' button on the back of the router, press and hold it for 5-10 seconds, and then let go when you see all the lights on the router flash.

Enter the IP address of the LAN port of the router in the browser, and enter the management username and password of the router correctly in the pop-up box.

Open the browser on the computer, enter it on the address bar, and then press enter, the password login window will pop up, enter the username and password are admin (the new version of the router sets the password by itself), and press [OK] to log in to the router web page.

After logging in, the [Setup Wizard] will automatically pop up. Select Network Parameters and WAN Port Settings in the left box, and then select PPPoE in WAN Port Connection Type in the right box. Fill in the username and password of the broadband account in the "Internet access" and "Internet password".

If the computer does not set the DNS server address, you can fill in the DNS server address displayed in the WAN port status display into the computer.

At this point, the PPPoE dial-up has been set and successfully dialed, enter the [Internet ID] and [Internet Password], and the computer under the router can already access the Internet through the router.

The details are as follows: 1. Equipment required:

1. Under normal circumstances, to install broadband Internet access in our home, we need to use two devices: wireless router and cat. However, it is not necessarily required, and it is directly related to the type of broadband service you handle and the demand for use.

2. Sun Yuan: If your home broadband is the best line and optical fiber access, then you must use the device of cat (optical modem) to access the Internet.

3. Network cable, if your broadband uses an optical modem or adsl dialer, and you have a desktop computer, then you need at least 2 network cables, 1 network cable to connect the router and the cat or ADSL dialer, and the other network cable to connect the computer and the router.

2. Installation steps:

1. The operator's line is connected to the modem, and the WAN port is connected to the network cable to our computer;

2. Find the network connection on the computer and click to set a new connection or network;

3. Select Connect to the Internet and click Next to continue.

4. Click Broadband PPPoE to enter the broadband connection settings;

5. Enter the password provided by the operator and click Connect to start dialing attempts.

6. The next time you use Nabend, you only need to find the broadband connection on the network connection page or on the desktop, click the right mouse button, and then select Connect. Cave Kai stuffy.

Are you still worried about how to dial up the Internet and wireless Internet access on the router, in the family, it is generally linked to the network through the virtual dial-up of the router, and other electronic devices are connected to the mobile phone, computer, etc., and then linked to the router to achieve the Internet function. Let me introduce how to set up a router to dial up Internet access.

Log in to your router. When setting up the router, you must first connect to the router through a computer or other device, and the login method can be found in the instructions on the back of the router. Enter **Enter your username and password.

After entering the main page of the router, click on the left side to see a setup wizard, click the setup wizard to enter the router dial-up related settings.

If you need to set other functions such as changing the login password, etc., you need to set up other navigation settings, click Next directly.

Since we need to dial up the Internet according to the broadband and password, we choose the second ADSL virtual dial-up method here.

Enter the broadband and password for Internet access, then click Next.

If it is a wireless router, you can set the wireless name and wireless password of the wireless router here, and it is best to use a more complex password to prevent others from rubbing the network.

After saving the settings, you can see that the settings are successful in the Internet time, and other devices can be connected to the wireless or use the network cable to connect to the Internet. end

1. Connect the computer to the cat (broadband network cable).

First of all, please plug the network cable from the network port of the cat into the network cable interface of the computer.

If you don't use the cat for your home's broadband, then plug the Internet cable directly into the network port of the computer.

2. Use a broadband connection to dial-up the Internet.

1. Open the "Broadband Connection" program in the computer desktop, fill in your broadband and broadband password in the program, and then click "Connect", and you're good to go. This is shown in the figure below.

2. Open the "Broadband Connection" program on your computer's desktop.

The office is estimated to be routed, usually a line to connect several computers, so the IP address is generally automatically assigned. Since the router is always on, you can turn on the computer and surf the Internet. If you are afraid that others will touch your things, you can set up a login account on the computer

Is it not good to go directly to the Internet? Do you want to dial for Shenma? Don't you think it's more convenient to dial up?

[Home Network Environment Wiring]:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter the Internet user name and password according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

Use a router to share the internet.

1. Connect the line, connect the WAN port to the external network (i.e. ADSL or other broadband), and connect the LAN port to the intranet, that is, your computer network card;

2. Each router has a default IP address, just look at the manual, mine;

3. Configure your computer IP as, gateway and DNS point to router, that is;

4. Open Internet Explorer on your computer, enter it, and enter the configuration interface of the router;

5. The general manual to this says that you can browse the web smoothly, in fact, we found that our computer can not be on the Internet at all, this is mainly the MAC address of the router is making trouble, we find the MAC address clone option, choose to clone the MAC address, and you can go to the Internet after saving. Figure 36, it should be noted that some routers do not have the option of MAC address cloning, then we only have to manually modify the MAC address of the router, and directly enter the IP address of our own computer network card in the MAC address option of the router, and the method of getting the MAC address of our own network card is:

Enter the command prompt and enter the Win2000 XP operating system as in"ipconfig /all", and press Enter. You can see that there is a string of characters (e.g. 00-e0-4c-9-b4-43), which is the MAC address.

The following sticker description Note: Please follow the red box in order to set it step by step.

If you don't have a router at home, you can buy one, about 60 yuan. If there is, it will be easy to do. Assemble all the cables (look carefully to know how to install them, don't worry).

Turn on the power of the router and the power of the computer. Open the router manual. Find the Setting PPPoE Internet Settings page.

Then enter it in the IE address bar of the computer (that is, where you type ** on the Internet) or depending on which one is written in the manual of your router. Then it prompts you to enter the account password, and then read the manual. Then take your time by following the steps on the instructions.

At the end of the day, the feature that opted in to IP auto-assignment seemed to be DHCP. Then set the IP address of the network card of the computer (right-click the network neighbor attribute and then you can see the network card, then continue to right-click the property, and switch the IP tab to see) all of them are automatically obtained. Finally, restart your computer and router.

Typing myself is slow as there is a problem pm me.

After configuring the router, connecting the router to the bandwidth, entering the router homepage, displaying "connection", and successfully obtaining the IP address and other information, the LAN port of the router (generally blue, and the number is 4 or 8), and your computer can be used to access the Internet normally.

Open IE browser http: The general account and password are admin If not, please see the manual to enter the settings interface, which will definitely go online, select PPPoe, fill in the correct Internet dial-up account and password, turn on the DHCP function, automatically obtain it on the computer, it is very simple, I wish you success, give additional points!

The router is easy to use!

The router is connected to the terminal crystal port, and the other crystal head is connected to the main computer.

Just connect the other machine to the router, and then remember to use the router's driver!

What the hell is telecom?,In the past, when there was no limit, n computers dialed together was no problem.,Now it's restricted.,Like us, we can only connect two computers.,It's even worse on your side.,You can only connect one.,In this way, multiple computers can intelligently go online together through the router.。 It's to buy a router,It's your broadband account password set into the router,And then the line is separated to the computer to access the Internet,If you don't know how to set it up, when you buy a router, the person who sells it will help you set it in,You just need to bring your account password on the line,And don't plug in the wrong line,ADSL cat and router WAN port connection,Routing LAN port and computer connection。

First of all, it is necessary to distinguish whether you are Netcom's network cable or Telecom's network, which corresponds to Netcom routing and telecommunications routing respectively.

After distinguishing, first insert the main line (and the network cable given to you by Netcom or Telecom) into the WAN port, and then find two network cables LAN port to connect with the two machines.

Right-click on a machine on the network neighbor properties - double-click on the local connection - properties - double-click Internet protocol input:

Then open the e icon (and browser) and type in the address bar.

Enter the routing login interface, generally enter the username and enter admin, and the password is admin to enter the routing settings page, and then follow the above prompts. Note: Take a look at the routing manual, there is a username and password in the manual.

The IP of the second station

Connect to the computer, enter an IP address after the router in the browser, enter the system settings to have a selected Internet access method, select ADSL to enter the username and password, and automatically obtain the IP and DNS settings, and you can do it. The security settings can be set by yourself.