The two computers cannot be connected through the hub

Runs on the machine:"ping "(x is the number you set, e.g. 1) If it can be connected, it proves that it is connected.

2. Enable the guest account (in the user group, if it is enabled, you can skip it), 3. Set the shared directory (you must select any directory on the hard disk to be shared), 4. Set the firewall (if you don't understand, you can set it to a low security level), and finally set the two machines in the same working level.

The default gateway doesn't need to be set up.

The two machines are set to the following IP addresses, 1).

Everything else is set by default.

And you need to set one (or several) of the hard disks of one (or two) of one of the computers to be shared, which is the presence of a hand tray.

This way you can find another computer and a shared hard drive in your online neighbors.

1。Ping each other to see if it works.

2。Is the firewall off?

3。Try FTP and see if it works.

Please change the number 1 to 11

Please change the number 2 computer to 12

That's why it's okay.

Please change the number one computer to 3 254 and try again.

You don't need a hub.

First of all, you need to make sure that the physical connection is correct, mainly with crossed wires! (Direct connection of the two machines) Secondly, set the IP address of the two machines, the specific method: right-click the network neighbor, select the attribute, right-click the local connection to select the attribute, and then double-click the Internet protocol, select the following IP address, set the subnet mask to OK and the other IP as the subnet mask to OK.

Finally, connect: Right-click on the property of what you are preparing to take the test to open and share in"Get started"Selected"Run"Then enter the IP of the machine you want to test) should be able to pull if it doesn't work, and then help you find a way!

I'll tell you the simplest way to connect.

Direct connection between two machines. Make a network cable, not a network cable for surfing the Internet. It is the fastest way to transfer files between two computers with only one network cable, without going through a hub or router. Just search for the relevant network cable practices.

You have to think about crossing the line.

The crossover cable is actually the same as the ordinary network cable, but the interface cable on both sides of the ordinary network cable is in the same order.

The wires in the interface at both ends of the crossover wire are in reverse order, just buy one.

If you use cross, you don't need a hub, it's much easier

1 Routed wirelessly.

2 Both computers are equipped with wireless network cards.

I'm not sure, but I have two of them at home, and I use a router, but some cards.

Install a wireless router Install a wireless broadband connection on your computer I hope it will help you.

The first thing I can tell you is that if you want to double-click on the interconnection, you don't need a hub, just a point-to-point network cable.

However, your network cable does not seem to be point-to-point, then your computer should be connected to the hub, and the IP of the computer should be set in a local area network, for example, the IP of computer A is, the IP of computer B is, and the subnet mask is set to, I just make an analogy, I can solve the problem for you, you don't want to master these knowledge, right, the gateway is set to, and the others do not need to be set, so that you can connect it.

They're all right!! I don't need to add anymore.

The hub is the hub.

If you want to go online, you need to have a router. Two of the ports of the hub are connected to two computers, and the hub --- the router are connected with a straight cable (plugged into the LAN port of the router). Then connect the network cable of the external network to the network port (WAN port) of the router.

Then you can set the dial-up on the management interface of the router.

If you want two computers to use a network line to access the Internet at the same time, you must have a router, and the home routers sold on the market now generally have 4 network cable sockets, and the hub will not be used. Connect the two computers to the LAN port of the router with network cables, and then connect the network port of the broadband modem to the WAN port of the router with a network cable, and set the router accordingly.

First of all, it is necessary to know whether your ADSL belt has a routing function, which can generally be found in the ADSL manual or on the Internet.

If your ADSL cat with routing function, OK, easy to do, just set the IP address of your computer to the same network segment as the IP address of ADSL (in the manual, or check on the Internet), open IE and enter the IP address of ADSL, set it up, after ADSL dial-up, your computer can already access the Internet.

If your ADSL doesn't have a routing feature, that's okay, a little more troublesome. The method is to make a server on a computer, install dial-up software on the server to surf the Internet, and install a proxy, ** software such as ccproxy. After installation, it has been turned on, and the other machine needs to set up the server to do it.

IE settings are set on the Tools option Connection, and there is a connection setting when QQ logs in. If you think it's troublesome, replace the hub with a router.

To put it simply, the IP addresses of two computers are set up separately to form the same network segment. For example: the first destruction hall lead platform ip: subnet mask: second computer subnet mask:. In this way, the LAN phase can be formed through the hub to facilitate mutual access.

Connect directly to the hub, and then set the IP of the two computers on the same network segment

1. Find a line tester and measure it.

2. Change the network cable.

If you use a hub, a machine must have two network cards as a server, so it is recommended that you use a broadband router.

hub, router, Bluetooth LAN is also OK.

How troublesome it is, change a 4-port router, as long as you set the IP address, after installation, the 2 computers can access the Internet independently, which is convenient.

It's troublesome to use the hub, and there is no routing function, so it's troublesome to set up.

The hub can't be set, the advanced switch can be set, but it's very expensive, the cheap one costs thousands, and the router can be set up.

The hub is a switch not a router, and you don't need any settings at all, so it is estimated that you have bought a poor quality hub. Small hubs are also very cheap, about forty or fifty yuan can be done.

The hub can be divided without setting.

If you're a router, then set it up.。。

There are also 2 machines that need to use routers.