After the computer passes through the router, neither computer can connect to the Internet?

Problems with router or computer settings.

Follow the instructions and see for yourself. You're talking too generally.

If it is not set up or there is a problem with the router, you can follow the instructions of the router step by step, it is very simple, if you can't access the Internet, it is recommended to change the router.

Set the routing IP address

Set the local IP

Just set up your router.

Is the route setting incorrect?

Wireless routers.

There are two ways to connect to the wireless router and set up the second router (provided that the first router has been set up):

The first method: dynamic IP mode (the first route is the primary route, and the second route is the slave route).

1. Plug in the router and do not connect the LAN port of the main router first, and reset the slave router (restore the factory);

2. Connect the computer from any LAN port of the router to enter the settings page;

3. Set according to the dynamic IP;

4. Then set the SSID, encryption method and password;

5. Save and restart;

6. After setting, connect the network cable from the LAN port of the main router to the WAN port from the router.

The second method: wireless AP

Manner. 1. Connect the computer to the LAN port of the router first, and change the IP address of the slave router. For example most router addresses are, we just want to take the IP address from the router.

Instead, it is sufficient; 2. Turn off the DHCP function from the router in the settings;

3. Finally, connect the network cable from the main router to the LAN port of the slave router (any one is fine), note that it cannot be the WAN port.

Is it that the router has no network or the computer has no network?!

If the router does not have a network, you need to check from the cat, first make sure that the cat has a network when it comes out, and then make sure that the router has a network.

If the router has a network and the computer does not have a network, is there more than one computer connection, but your IP is conflicting, it is best to change the IP address of your computer, do not get it automatically, and set a non-conflict by yourself.

Dear, what do you mean by the two routers, the computer is not connected to the Internet, it is estimated that the router is not working properly, or the settings are incorrect, it is recommended to connect the computer to the main router, and manually set the IP address, it should be able to ensure that the computer is connected to the Internet normally.

If you want to connect to the second router, then you have to set the IP of the second router, otherwise the computer will see both routers as the address of one router, so the second router will have no network signal.

If you want to connect two routers, you need to set up the router, if you don't set it up, it may cause an address conflict and you can't access the Internet, you can connect to the computer after making sure that both routers can access the Internet.

This is obviously the wrong connection of the router, or the connection is not normal caused by the inability to connect to the network, you can directly find the operator to assist in debugging and you can connect to the network after successful debugging.

First of all, determine whether the router can access the Internet, if it can access the Internet, and the connection to the computer can not access the Internet, it means that the network cable or the computer is a problem.

The two routers need to be connected to each other, and the IP address cannot be on the same network segment. If the router is in a network segment, it will cause IP conflicts, so you can't access the Internet.

Summary. Step 1.

First, open the network connection in the computer to see if the network card is enabled or disabled, and click "Start" - "Control Panel".

Step two. In the Control Panel, select Network & Internet, and click View Network Status and Tasks

Step 3. On the page that opens, click "Change adapter settings".

Step 4. If the "Local Connection" (NIC) is disabled, right-click "Local Connection" and click "Enable" in the pop-up dialog box to enable the local connection. If you can't see "Local Connection", or the system does not detect the network card, or the network card driver is lost, or the network card is damaged, and the network card driver is not detected and the network card driver is lost, the computer can be restarted to reinstall automatically; If the network card is damaged, replace the network card, and install an independent network card if the integrated network card is damaged.

Step five. Confirm that the NIC is enabled, but the router is not connected, then click "Start" - "Run" "cmd" Enter to open the command line manager.

Step 6. Enter "ping is the router IP address (

The two routers at home and the computers are not connected to the Internet.

Step 1: Open the network connection in the computer to see if the network card is turned on or disabled, click "Start" - "Control Panel" Step 2 Select "Network and Internet" in the "Control Panel", click "View Network Status and Tasks" Step 3 Click "Change Adapter Settings" in the page that opensStep 4 See if the network card (i.e. local connection) is disabled or there is no network adapter, if the "local connection" (network card) is disabled, right-click "Local Connection", Click "Enable" in the pop-up dialog box to enable the local connection; If you can't see "Local Connection", or the system does not detect the network card, or the network card driver is lost, or the network card is damaged, and the network card driver is not detected and the network card driver is lost, the computer can be restarted to reinstall automatically; If the network card is damaged, replace the network card, and install an independent network card if the integrated network card is damaged. Step 5: Make sure that the NIC is enabled, but the router is not connected, then click "Start" - "Run" and "cmd" press Enter to open the command line manager. Step 6: Enter "ping is the router IP address (.").

Step 7: Check whether the router is turned on, and then check whether the network cable connector has been oxidized or plugged in. Step 8: Go back and ping the router again, if there is a signal reply as shown in the figure, it is connected. Step 9: If the above two types of unconnected pings occur again, you can restart the router, redo the network cable connector, and then change to someone else's router and try whether your router is damaged, if it is damaged, replace it.